• Membrane Journal
• /
• v.26 no.2
• /
• pp.97-107
• /
• 2016

This study was carried out to prepare a heterogeneous cation exchange membrane by mixing polyvinylidene fluoride (PVDF), commercial cation exchange resin and sulfonated poly(phenylene oxide)(SPPO) in order to propose an optimum condition for the preparation, and to compare its properties with commercial membrane. Study results show that the ion exchange capacity and electrical resistance were outstanding when the ratio of polymer matrix was less than 30% comparing between PVDF-IER, PVDF-SPPO and PVDF-SPPO-IER. The tensile strength was confirmed that seemed a hard look was five times greater compared to the commercial heterogeneous membrane, despite the weak durability of PVDF resin. Therefore, when chemical and mechanical properties are considered, the optimum mixing ratio between PVDF, IER and SPPO was 30 : 70, at which electric resistance was measured as $3{\sim}5{\Omega}{\cdot}cm^2$, ion exchange capacity as 0.6~1.0 meq/g, while mechanical strength was in a range of $12{\sim}15kgf/cm^2$.

• Journal of the Korean Chemical Society
• /
• v.30 no.3
• /
• pp.273-281
• /
• 1986

This study is focused on the correct measurement of the equations for the determination of the impedance parameters-the differential capacity of the double layer $C_d$, solution resistance $R_Q$, transfer resitance $R_i$, and adsorption pseudcapacity $C_{\phi}$/ The application of only an imaginary part of complex function of ${\omega}$ at the sinusoidal steady state indicates the following equations of total impedance: at low frequency $|Z_{LF}|=1/{\omega}_1\;C_{\phi}\;{\sqrt{1+{{\omega}_1}^2/{\omega}^2}$, at high frequency $|Z_{HF}|={\omega}_2/({\omega}_1{\omega}_3C{\phi})({\omega}^2+{{\omega}_2}^2)\;{\sqrt{{({\omega}^2+{\omega}_2{\omega}_3)}^2+{({\omega}_2{\omega}-{\omega_3{\omega})^2}}$. The values of the total impedance of cell, phase angle, and cell current that are necessary for the calculations of impedance parameters were experimentally measured from 200 to 6000Hz for the following supporting electrolytes, 0.5M $Na_2SO_4$, 1M NaCl, 19.373% sea water, 1M HCl, 1M $KNO_3$ and for $10^{-2}M$ KI and 60mM DBNA (Di-iso-Butylnitrosoamine) in these supporting electrolytes. The derived equations in this study shows that the values of impedance parameters of $C_d,\;C_{\phi},\;R_i\;and\;R_Q\;are\;15{\sim}40\;{\mu}F/cm^2,\;162{\sim}758\;{\mu}F/cm^2\;11.5{\sim}57.6\;ohm{\cdot}cm^2\;and\;0.5{\times}10^{-2}{\sim}4.1{\times}10^{-2}\;ohm{\cdot}cm^2$ respectively.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.5
• /
• pp.91-97
• /
• 2012

Recently, the performances of electrical and electronic devices are improving while the sizes are becoming smaller. As sound-generating systems, the two-dimensional speakers have been developed in place of conventional three-dimensional ones. Piezoelectric materials show the mechanical vibrations due to the voltage applied from outside the materials. The early film speakers had a limitations of output power in that it was not easy to make the conducting macromolecular films on the surfaces of the materials due to the internal chemical properties of materials. We have adopted the corona surface treatment in order to improve the output characteristics by increasing the adhesion of the coating material on to the surface of the center material of piezo film. The results showed the improvement of output power in the wider range of operating frequencies.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.260-260
• /
• 2012

최근 IT산업의 급속한 발달로 모바일 제품과 반도체 및 IC 패키지 등의 전자제품의 소형화, 경량화 및 고성능화되어 가고 있다. 따라서 반도체 공정에서 단위소자의 고속화를 구현하기 위한 금속배선공정에 사용되는 금속재료가 최근에 최소 선폭을 갖는 디바이스에서는 구리를 배선 재료로 전환하고, 향후에는 모든 디바이스가 구리를 주요 배선재료로 사용할 것으로 예측되고 있다. 반도체 소자 공정 중 시료 표면 위에 형성되는 오염물은 파티클, 유기오염물, 금속 불순물 그리고 자연 산화막으로 나눌 수 있다. 구리 표면에 생성되는 부식생성물의 종류에는 CuO, $Cu_2O$, $Cu(OH)_2$, $CuCO_3{\cdot}Cu(OH)_2$와 같은 생성물들이 있다. 이러한 부식생성물이 구리박막 표면에 형성이 되면 성장된 구리박막의 특성을 저하시키게 된다. 이러한 다양한 오염물들을 제거하기 위해서 여러 가지 전처리 공정에 대한 연구가 보고되고 있다. 본 연구에서, 스퍼터 방식으로 구리를 증착한 웨이퍼 (Cu/Ti/Si) 를 대기 중에 노출시켜 자연 산화막을 성장시키고, 이 산화막과 대기로부터 흡착된 불순물을 제거하기 위해 계면 활성제인 TS-40A와 $NH_4OH$ 수용액을 사용하여 이들 수용액이 구리 표면층에 미치는 영향에 대해 조사 분석하였다. 사용된 TS-40A는 알칼리 탈지제로서 웨이퍼 표면의 유기물을 제거하는 역할을 하며, $NH_4OH$는 구리를 제거하는 부식액으로 산업현장에서 널리 사용되고 있다. 다양한 표면 전처리 조건에 따른 구리박막 표면의 형상 및 미시적 특성변화를 SEM과 AFM을 이용하여 관찰하였고, 표면의 화학구조 및 성분 변화를 관찰하기 위해 XPS를 측정하였으며, 전기적 특성변화를 관찰하기 위해 4-point prove를 사용하여 박막의 면저항을 측정하였다.

• Economic and Environmental Geology
• /
• v.55 no.4
• /
• pp.377-388
• /
• 2022

Laboratory-scale experiments were performed to identify the As removal mechanism of the residual slag generated after the mineral carbonation process. The residual slags were manufactured from the steelmaking slag (blast oxygen furnace slag: BOF) through direct and indirect carbonation process. RDBOF (residual BOF after the direct carbonation) and RIBOF (residual BOF after the indirect carbonation) showed different physicochemical-structural characteristics compared with raw BOF such as chemical-mineralogical properties, the pH level of leachate and forming micropores on the surface of the slag. In batch experiment, 0.1 g of residual slag was added to 10 mL of As-solution (initial concentration: 203.6 mg/L) titrated at various pH levels. The RDBOF showed 99.3% of As removal efficiency at initial pH 1, while it sharply decreased with the increase of initial pH. As the initial pH of solution decreased, the dissolution of carbonate minerals covering the surface was accelerated, increasing the exposed area of Fe-oxide and promoting the adsorption of As-oxyanions on the RDBOF surface. Whereas, the As removal efficiency of RIBOF increased with the increase of initial pH levels, and it reached up to 70% at initial pH 10. Considering the PZC (point of zero charge) of the RIBOF (pH 4.5), it was hardly expected that the electrical adsorption of As-oxyanion on surface of the RIBOF at initial pH of 4-10. Nevertheless it was observed that As-oxyanion was linked to the Fe-oxide on the RIBOF surface by the cation bridge effect of divalent cations such as Ca²⁺, Mn²⁺, and Fe²⁺. The surface of RIBOF became stronger negatively charged, the cation bridge effect was more strictly enforced, and more As can be fixed on the RIBOF surface. However, the Ca-products start to precipitate on the surface at pH 10-11 or higher and they even prevent the surface adsorption of As-oxyanion by Fe-oxide. The TCLP test was performed to evaluate the stability of As fixed on the surface of the residual slag after the batch experiment. Results supported that RDBOF and RIBOF firmly fixed As over the wide pH levels, by considering their As desorption rate of less than 2%. From the results of this study, it was proved that both residual slags can be used as an eco-friendly and low-cost As remover with high As removal efficiency and high stability and they also overcome the pH increase in solution, which is the disadvantage of existing steelmaking slag as an As remover.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.155-155
• /
• 2011

용융탄산염 연료전지(MCFC)는 $650^{\circ}C$에서 작동하는 고온형 연료전지 시스템이다. 이 시스템은 천연가스 등을 개질하여 생산된 수소를 바로 전기로 생산할 수 있는 시스템으로 열효율이 높으며, 현재 대체 발전시스템으로 각광을 받고 있다. MCFC는 개질방식에 따라 내부개질 방식과 외부개질 방식이 있다. 내부개질 방식은 수소를 생산하는 개질기가 스택내부에 장착된 형식으로 천연가스를 스택내부에서 개질하여 바로 전기를 생산하는 방식이다. 이 내부개질반응에 사용되는 촉매로는 알루미나에 고함량 (약 50 wt.%)으로 담지된 니켈(Ni) 계열촉매이 주로 쓰이고 있다. 이 고함량으로 담지된 촉매는 대부분 높은 활성을 보인다. 비교적 낮은 온도 운전조건 (약 $580{\sim}620^{\circ}C$)을 가지는 MCFC 내부개질에 적용하기 위해서는 활성점인 니켈을 최대한 담지체에 고르게 분산 시켜야한다. 이를 위해서 MgO를 이용하여 촉매의 활성점을 높게 분산시키는 연구를 진행 하였다. 촉매를 제조하는 방법으로 요소(urea)를 이용한 균일용액침전법을 이용하였다. 니켈함량은 50 wt.%로 고정을 한 다음, MgO 양과 $Al_2O_3$ 양을 각각 0 ~ 45 wt.%와 5 ~ 50 wt.%로 조절하면서 촉매를 제조하여 그 특성들을 분석하였다. 물성을 비교하기 위해서, X-선 회절분석 (XRD) 및 TPR, 물리화학흡착 실험을 하였다. 촉매의 활성을 살펴보기 위해서, fresh 상태 및 피독 상태에서 메탄수증기 개질활성 실험을 실시하였다. MgO 함량이 없거나 적은 촉매에서는 높은 BET surface area와 작은 NiO, metallic Ni 결정 크기가 나타났다. 반면 MgO 함량이 높은 촉매에서 낮은 BET surface area와 비교적 큰 NiO, metallic Ni 결정 크기가 나타났다. 또한 XRD 분석에서 MgO 함량이 증가할 수 록 MgO 결정 피크가 명확히 나타났으며, $MgAl_2O_4$ 피크는 나타나지 않았다. TPR 분석에서 촉매들의 환원 피크를 측정한 결과, 저함량의 MgO를 포함한 촉매는 $700^{\circ}C$ 부근에 환원 피크가 관찰되었고 MgO가 고함량인 촉매는 환원 피크가 $400^{\circ}C$ 부근에서 관찰되었다. 촉매의 초기 fresh 상태에서의 활성은 고함량 MgO를 포함한 Ni-90M10A 샘플을 제외하고 모든 촉매가 거의 비슷하게 나타났다. 그러나 $K_2CO_3$ 피독 상태에서는 MgO 함량이 증가할 수 록 활성이 좋지 않았음을 알 수 있었다. 따라서 MgO가 소량 포함된 촉매의 경우 fresh 상태에서는 우수한 물성과 활성을 보이지만, 피독상태에서는 MgO가 포함되지 않은 Ni-$Al_2O_3$ 촉매가 우수한 활성을 보였다.

• Applied Chemistry for Engineering
• /
• v.29 no.2
• /
• pp.191-195
• /
• 2018

In this study, the influence of microporous structures of activated carbon fibers (ACFs) on dimethyl methylphosphonate (DMMP) gas sensing properties as a nerve agent simulant was investigated. The pore structure was given to carbon fibers by chemical activation process, and an electrode was fabricated for gas sensors by using these fibers. The PAN based ACF electrode, which is an N-type semiconductor, received electrons from a reducing gas such as DMMP, and then electrical resistance of its electrode finally decreased because of the reduced density of electron holes. The sensitivity of the fabricated DMMP gas sensor increased from 1.7% to 5.1% as the micropore volume increased. It is attributed that as micropores were formed for adsorbing DMMP whose molecular size was 0.57 nm, electron transfer between DMMP and ACF was facilitated. In conclusion, it is considered that the appropriate pore structure control of ACFs plays an important role in fabricating the DMMP gas sensor with a high sensitivity.

• Economic and Environmental Geology
• /
• v.41 no.6
• /
• pp.657-672
• /
• 2008

The purposes of this study are to investigate the hydrogeochemical characteristics of groundwaters around Keumsan municipal landfill, and to evaluate the contaminant dispersion from the landfill and its environmental impact. To achieve these goals, groundwater quality logging, hydrochemical analysis, multivariate statistical analysis, and contaminant transport modeling were performed. The water quality logging indicated a leaking from the landfill at the depth of 4-12m around a leachate sump. Electrical conductivity data indicated that groundwaters within 70-100m from landfill were affected by the landfill leakage. Principal components 1 and 2 obtained from principal components analysis (PCA) reflect the influence of leachate and the characteristics of aquifer media, respectively. The results of principal component analysis also indicated the natural attenuation processes such as cation exchange, sorption, and microbial biodegradation. The modeling results showed that groundwater flow westward along a valley from the landfill and contaminants transport accordingly.

• Korean Journal of Soil Science and Fertilizer
• /
• v.39 no.3
• /
• pp.144-150
• /
• 2006

Chemical characteristics and their interrelationships of 156 soils included by 74 sandy loam and 82 loam soils collected from plastic film house in Chungbuk area were investigated from 1998 to 2001. Seventeen chemical properties including pH, organic matter (OM), electrical conductivity (EC), inorganic nitrogen, available phosphorus, exchangeable cations, CEC, etc., were analyzed by correlation, standardized partial regression coefficient, and principal factor analysis. Standardized partial regression coefficients of chemical properties were estimated to determine the degree of contribution of EC and OM contents in soils. Principal factor analysis was applied to classify the studied chemical properties into different groups having similar chemical properties. The pH of experimental soils ranged from 4.24 to 7.14 and 4.95 to 7.35 for loam and sandy loam soils, respectively. The EC of soils varied from 0.93 to $15.65dS\;m^{-1}$ for loam and $0.91{\sim}22.30dS\;m^{-1}$ for sandy loam soils, respectively with significant differences among them. The EC measured by 1:5 $H_2O$ dilution method and saturation method were significantly related with 8.163 and 8.599 as the slopes of regression equation for loam and sandy loam soils, respectively. These slopes more than 8.0 in this regression equation was higher than the slope of 5.0 that is estimated from dilution coefficient suggesting that EC measured by 1:5 dilution method might be erratic. The standardized partial regression coefficient of different chemical properties for the estimation of EC was in the order of $NO_3{^-}$ > $Cl^-$ > OM > exchangeable Mg for loam soils and $NO_3{^-}$ > exchangeable Mg > $Cl^-$ for sandy loam soils. Contribution order of the chemical properties based on standardized partial regression coefficient differed 1:5 dilution method and saturation method, indicating that different chemical compounds might be present in the extract solutions of these two methods. Consequently the measurement of EC by saturation method was thought be still better for estimation of chemical property because accuracy of EC measurement by 1:5 dilution method can't be improved by any specific coefficient for adjustment of EC. Regardless of differences in soil textures and extraction methods, correlation coefficients between EC and the other chemical properties were routinely in the order of $NO_3{^-}$ > $Cl^-$ > degree of base saturation > exchangeable Mg > exchangeable Ca > $SO{_4}^{2-}$. The principal factor analysis revealed four factor groups of the chemical properties studied. The groups for sandy loam were as follows; ; 1. salt components, 2. soil reaction components, 3. fixed and adsorption components, 4. CEC components. The groupings of loam soils were similar to sandy loam except that exchangeable Na substituted the CEC of sandy loam.

• Journal of the Korean Electrochemical Society
• /
• v.12 no.3
• /
• pp.263-270
• /
• 2009

Carbon felt surface was modified by heat or acid treatment in order to use for the electrode of a redox-flow battery. Polymers on the surface of carbon felt was removed and oxygen-containing functional group was attached after the thermal treatment of carbon felt. Thermal treatment was better for the stability of the carbon structure than the acid treatment. Oxygen-containing functional group on the thermally treated carbon felt at 500$^{\circ}C$ was confirmed by XPS and elementary analysis. BET surface area was increased from nearly zero to 96 $m^2/g$. Thermally treated carbon felt at 500$^{\circ}C$ showed lower activation polarization than the thermally treated carbon felt at 400$^{\circ}C$ and the acid-treated carbon felt in the cyclicvoltammetry and polarization experiments. The thermally treated carbon felts at 400$^{\circ}C$ and 500$^{\circ}C$ and the acid-treated carbon felt was applied for the electrode to prepare vanadium redox flow battery. Voltage efficiencies of charge/discharge were 86.6%, 89.6%, and 96.9% for the thermally treated carbon felts at 400$^{\circ}C$ and 500$^{\circ}C$ and the acid-treated carbon felt, respectively.