• Journal of IKEEE
• /
• v.23 no.4
• /
• pp.1461-1464
• /
• 2019

In this paper, we propose the development of embedded board for integrated radiation exposure protection fireman's life-saving alarm capable of location tracking and radiation measurement. The proposed techniques consist of signal processing unit, communication unit, power unit, main control unit. Signal processing units apply shielding design, noise reduction technology and electromagnetic wave subtraction technology. The communication unit is designed to communicate using the wifi method. In the main control unit, power consumption is reduced to a minimum, and a high performance system is formed through small, high density and low heat generation. The proposed techniques are equipment operated by exposure to poor conditions, such as disaster and fire sites, so they are designed and manufactured for external appearance considering waterproof and thermal endurance. The proposed techniques were tested by an authorized testing agency to determine the effectiveness of embedded board. The waterproof grade has achieved the IP67 rating, which can maintain stable performance even when flooded with water at the disaster site due to the nature of the fireman's equipment. The operating temperature was measured in the range of -10℃ to 50℃ to cope with a wide range of environmental changes at the disaster site. The battery life was measured to be available 144 hours after a single charge to cope with emergency disasters such as a collapse accident. The maximum communication distance, including the PCB, was measured to operate at 54.2 meters, a range wider than the existing 50 meters, at a straight line with the command-and-control vehicle in the event of a disaster. Therefore, the effectiveness of embedded board for embedded board for integrated radiation exposure protection fireman's life-saving alarm has been demonstrated.

• Korean Journal of Ecology and Environment
• /
• v.41 no.3
• /
• pp.382-394
• /
• 2008

The objective of this study was to analyze temporal trends of water chemistry and spatial heterogeneity between the dam site (Daecheong Reservoir, S1) and the downstream (S2$\sim$S4) using water quality dataset (obtained from the Ministry of Environment, Korea) during 2000$\sim$2007. Water quality, based on eight physical and chemical parameters, varied largely depending on the years, sampling sites, and the discharge volume. Conductivity and nutrients (TN and TP) showed a decreasing trend in the downstream (S4) rather than the dam site during the monsoon. Spatial variation increased toward downstream (S4) from Daecheong Reservoir (S1). Also, BOD and COD increased toward downstream. Because of input of nutrient and pollutant nearby S1, lentic ecosystem in monsoon, BOD and COD were slightly increased. whereas relatively decreased in S4, lotic ecosystem in monsoon, by dilution effect of nutrient and pollutant by discharge from upper dam, S1. Spatial variation of SS increased toward downstream (S4) by the side of Daecheong Reservoir (S1). Based on the dataset, efficient water quality management in the point source tributary streams is required for better water quality of downstream. Monthly characteristics of DO showed the lowest value in the monsoon that tend to increase water temperature. DO was lowest in October at S1 because turbid water, input to the Daecheong Reservoir in the monsoon affect to the postmonsoon period. In contrast, water temperature increased toward summer monsoon, in spite of some differences showed between S1 and S4 environment. Overall, the characteristics of water quality in downstream region have close correlation with discharge amount of Daecheong Reservoir. Thus, those characteristics can explain that discharge control of upper dam mainly affect to the water quality variation in downstream reach.

• Journal of Korean Society of Forest Science
• /
• v.86 no.4
• /
• pp.415-421
• /
• 1997

The objectives of this study were to obtain standardized basic data on cambial electrical resistance (CER) of ornamental trees to be used for estimation of tree vigor and to compare CER between shrubs, deciduous, and coniferous trees in relation to bud opening, flowering, and growth cessation. Eighty healthy trees with four trees each for twenty ornamental tree species growing at an university campus in Suwon were selected and their CER was measured using a Shigometer every week from March to May, once a month from June to October and every two weeks in November, 1996. The CER of all tree species was high in March, started to decrease in April, maintained minimum in May through August, began to increase in September, and returned in November to the similar high level to March. Among the 20 species, Metasequoia glyptostroboides showed the lowest($5.5k{\Omega}$) annual average CER, while Cercis chinensis and Ligustrum obtusifolium had the highest($22.7k{\Omega}$, $22.9k{\Omega}$) annual average CER. The lowest CER($2.4k{\Omega}$) in summer(June through August) was obtained from Wisteria floribunda, second lowest($2.5k{\Omega}$) from Metasequoia glyptostroboides, the highest CER($46.8k{\Omega}$) during dormant season from Euonymus japonica, and second highest($45.0k{\Omega}$) obtained from Ligustrum obtusifolium. The CER of most species, particularly shrub species, started to decrease with bud opening, and many species, particularly shrubs and deciduous trees with large amount of flowers, showed sharp decrease with flowering. When CER was compared between shrubs and trees, shrubs showed higher average CER than trees, and seasonal difference in CER of evergreen species was smaller than that of deciduous species. It is interesting to note that the deciduous Metasequoia glyptostroboides had the lowest annual average CER.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1991.04a
• /
• pp.95-98
• /
• 1991

회전 기기의 이상으로 인하여 발생하는 진동은 축 회전속도의 고주파 성분 (super-harmonic)이나 또는 분수조파 성분(sub-harmonic)으로 나타나는 경 우가 대부분이기 때문에 회전기기의 진동을 주파수 영역에서 해석함에 있어 파워 스펙트럼의 주파수 축을 Hz로 나타내기보다는 축 회전속도의 order로 써 나타내는 것이 매우 유용하다. 스펙트럼을 order로써 나타내기 위해서는 샘플링 시간을 축 회전속도와 동기(synchronization)시켜야 하는데 이 방법으 로는 회전축에 엔코더(encorder)를 부착하여 엔코더에서 발생하는 펄스 신호 를 이용하여 샘플링하는 방법과 order tracking 필터를 이용하는 방법이 있 다. 그러나 전자의 방법은 원하는 회전축마다 엔코더를 부착하여야 하며 경 우에 따라서는 엔코더를 부착하기가 어려운 경우도 있으며, 회전기기의 운전 개시나 종료시처럼 회전속도가 급격히 변화하는 경우에는 낮은 주파수에서 중첩(aliasig)에 의한 오차가 수반될 수도 있다. 후자의 방법은 order tracking 필터 이외에도 여러 부수장비가 필요하며 기준 주파수(즉 회전속 도)가 급격히 변화하는 경우 PLL(phase locked loop)에서 tracking 오차가 발생된다. 최근에 발표된 논문에서 일정한 시간간격으로 샘플링한 데이터들 로부터 신호를 재합성하여 회전축의 속도와 동기가 되도록 재 샘플링함으로 서 스펙트럼의 주파수를 회전속도의 order로써 나타내는 방법을 제시하였다. 그러나 위 논문에서는 신호의 재합성에 필요한 재합성 필터(reconstruction filter)의 설계 방법에 대하여 구체적인 언급이 없이 다만 결과만을 논하였다. 따라서 본 논문에서는 재합성 필터의 설계 방법에 대하여 구체적인 방법을 제시하고 또한 동기화 샘플링의 장점 및 고려 사항에 대하여 고찰하였다. 고려한 능동 소음제어 에 대해 연구하였다. 경량화 추세에 따라 지반이나 케이싱이 경량이거나 유연하여 회전축과 동적으로 연성된 경우 회전축-베어링-지반으로 이루어진 2중구조의 회전축 계 동특성을 해석할 수 있는 프로그램을 개발하므로서 회전 기계류의 진동 전반에 걸친 문제점에 대한 그 원인과 현상을 명확히 분석하여 국내의 전기 계류의 보다 신뢰성있는 설계 및 제작자료를 확보하는데 기여할 수 있게 하 였다.존의 small molecular Gd-chelate에 비해 매우 큼을 알 수 있었다. MnPC는 간세포에 흡수된 후 담도계로 배출되는 간특이성 조영제임을 확인하였다. 장비 내에서 반복 시행한 평균값의 차이는 대체적으로 유의한 차이가 없었으나, 다른 장비에서 반복 시행한 장비간의 사이에는 유의한 차이가 있는 경우가 더 많았다. 따라서 , MRS 검사를 소뇌나 뇌교의 어떤 절환에 적용하기 전에 각 장비 마다 정상 기준치를 반드시 얻은 후에 이상여부를 판 정하는 것이 필수적이라고 생각된다.EX> 이상이 적절한 진단기준으로 생각되었다. $0.4{\;}\textrm{cm}^3$ 이상의 좌우 부피차를 보이는 모든 증례에서 육안적으로도 해마위축이 뚜렷이 나타났다. 결론 : MR영상을 이용한 해마의 부피측정은 해마경화증 환자의 진단에 있어 육안적인 MR 진단이 어려운 제한된 경우에만 실제적 도움을 줄 수 있는 보조적인 방법으로 생각된다.ofile whereas relaxivity at high field is not affected by τS. On the other hand, the change in τV does not affect low field profile but strongly in fluences on both inflection fie이 and the maximum relaxivity value. The re

• Journal of the Korean Electrochemical Society
• /
• v.6 no.1
• /
• pp.41-47
• /
• 2003

For the development of low temperature anode-supported planar solid oxide fuel cell, the planar anode supports with the thickness of 0.8 to 1 mm and the area of 25, 100 and $150\;cm^2$ were fabricated by the tape casting method. The strength, porosity, gas permeability and electrical conductivity of the planar anode support were measured. The porosity of anode supports sintered at $1400^{\circ}C$ and then reduced in$H_2$ atmosphere was increased from $45.8\%\;to\;53.9\%$. The electrical conductivity of the anode support was $900 S/cm\;at\; 850^{\circ}C$ and its gas permeability was 6l/min at 1 atm in air atmosphere. The electrolyte layer and cathode layer were fabricated by slurry dip coating method and then had examined the thickness of $10{\mu}m$ and the gas permeability of 2.5 ml/min at 3 atm in air atmosphere. As preliminary experiment, cathode multi-layered structure consists of LSM-YSZ/LSM/LSCF. At single cell test using the electrolyte layer with thickness of 20 to $30{\mu}m$, we achieved $300\;mA/cm^2$ and 0.6V at $750^{\circ}C$

• Journal of the Korean Wood Science and Technology
• /
• v.46 no.5
• /
• pp.511-526
• /
• 2018

Effects of heat treatment on the characteristics of Royal paulownia (Paulownia tometosa) wood were investigated. The results were compared with those of Suwon silver poplar (Populus tementiglandulosa) and Korean red pine (Pinus densiflora) woods. The wood samples of the three species were treated at $160^{\circ}C$, $180^{\circ}C$, $200^{\circ}C$ and $220^{\circ}C$ in an electric furnace for 2 hours. The changes of color, density, mass loss, and relative crystallinity were investigated before and after heat treatment. The lightness ($L^*$) decreased rapidly from $200^{\circ}C$ in all species. There were no change in red-green chromaticity($a^*$) and yellow-blue chromaticity($b^*$) of Royal paulownia and poplar woods with increasing temperature. Whereas, yellow-blue chromaticity($b^*$) of Korean red pine wood decreased sharply from $200^{\circ}C$. Royal paulownia wood showed appreciable color change(${\Delta}E^*$) after heat treatment above $180^{\circ}C$. Poplar and pine woods, however, presented significant color change from $160^{\circ}C$. Color change of the three wood species increased rapidly with increasing temperature. Mass loss of the three wood species by heat treatment was the highest in the Royal paulownia wood and the lowest in the pine wood. Mass loss and relative crystallinity increased and density decreased slightly with increasing temperature. Consequently, it is revealed that Royal paulownia wood showed considerable differences in the temperature of color change, weight loss and change of relative crystallinity compared to the other wood species.

• Journal of Soil and Groundwater Environment
• /
• v.10 no.4
• /
• pp.33-44
• /
• 2005

On the basis of a stepwise and careful integration of various field and laboratory methods the analysis of groundwater flow characterization was performed with five boreholes (BH-1, -2, -3, -4, -5) on a pilot site of Natural Forest Park in Guemsan-gun, Chungcheongbook-do, Korea. The regional lineaments of NW-SE are primarily developed on the area, which results in the development of many fractures of NW-SE direction around boreholes made in the test site for the study. A series of surface geological survey, core logging, geophysical logging, tomography, tracer tests, and heat-pulse flowmeter logging were carried out to determine fracture characteristics and fracture connectivity between the boreholes. In the result of fracture connectivity analysis BH-1 the injection well has a poor connectivity with BH-2 and BH-3, whereas a good with BH-4 and BH-5. In order to analyse the hydraulic connectivity between BH-1 and BH-5, in particular, a conspicuous groundwater outflux in the depth of 12 m and influx in the depth of 65 m and 70 m, but partly in/outflux occurred in other depths in BH-5 were observed as pumping from BH-1. On the other hand, when pumping from BH-5 the strong outflux in the depths of 17 m and 70 m was occurred. The spatial connectivity between the boreholes was examined in the depth of 15 m, 67 m, and 71 m in BH-1 as well as in the depth of 15 m, 17 m, 22 m, 72 m, and 83 m in BH-5.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.6
• /
• pp.613-619
• /
• 2006

The objectives of this research are to evaluate the effect of membrane materials, particulate matter and membrane pore size on permeate flux. It was shown that the removal efficiency of high MW organic matter more than 10 kDa was lower than that of low MW organic matter for $MIEX^{(R)}$ process. For the change of permeate flux by the pretreatment process, $MIEX^{(R)}+UF$ process showed high removal efficiency of organic matter as compared with coagulation+UF processes, but high reduction rate of permeate flux was presented through the reduction of removal efficiency of high MW organic matter. The pretreatment of the raw water significantly reduced the fouling of the hydrophilic membrane, but did not decrease the flux reduction of the hydrophobic membrane. Flux decline on MF process increased due to the pore clogging, while the permeate flux decline of UF process decreased due to the formation of cake layer. It was shown that particle matter was not effect on MIEX+membrane process. But, for coagulation+membrane process, particle matter was important factor on permeate flux.

• Journal of the Korean Chemical Society
• /
• v.30 no.1
• /
• pp.19-26
• /
• 1986

A titanium oxide thin films were prepared by air oxidation and vapour oxidation and a $TiO_2$ single crystal was reduced by heating in an argon atmosphere. All the electrode characteristics of the Ti$O_{2-x}$, thin films are not different from those of slightly reduced single crystal rutile. In cyclic voltammogram of oxygen containing electrolyte solution at Ti$O_{2-x}$ electrodes, cathodic peaks were observed at between -0.8V and -1.0V vs. SCE. The cathodic current near 0V vs. SCE in saturated solution with nitrogen was observed to be greater than in saturated solution with air. The chronoamperogram was represented by the equation of i = $i_0e^{-kt}$, when the rate constant k was represented by the equation of k =$k_0{[H^+]}^nexp(A{\eta}+E_a/RT)$ The values of activation energy $E_a $were found to be 4.6~4.8kcal/mole in overpotential range of 0.035∼0.145 V and 1.6kcal/mole in overpotential range of 0.2∼0.5V. The values of n and A were found to be 0. 1 and 5.4~5.6/V in range of 0.035~0.145V, and in range of 0.2~0.5V, to be 0.04 and 1.3/V, respectively. This can be interpreted as an totally irreversible reduction of oxygen.

• Journal of Periodontal and Implant Science
• /
• v.34 no.3
• /
• pp.671-681
• /
• 2004

Genomic Project 이후로 다양한 질환에 있어서 유전적인 영향에 관한 연구가 진행되고 있다. 이 연구의 목적은 한국인 치주질환 환자에서 Fc ${\gamma}R$ 유전자의 유전자다형성과 치주질환 특성과의 관련성을 알아보는 것이다. 치주적으로 건강한 한국인 90명(대조군, 남자64명, 여자26명), 중도 만성 치주염환자 40명(severe chronic periodontitis patients; severe CP, 남자 24명, 여자 16명)을 대상으로 임상지수(치주낭 깊이, 입상부착소실, 치은지수, 치태지수, 탐침 후 출혈지수, 치조골소실)를 측정하였다. 또한 이들의 정맥혈에서 추출한 DNA를 PCR(Polymerase Chain Reaction)법, 전기영동법 등을 이용하여 Fc ${\gamma}RIIIa$ , Fc ${\gamma}RIIIb$의 대립유전자의 존재여부를 확인하였다. 이를 바탕으로 각 유전자의 다형성 및 Fc ${\gamma}R$ 복합유전자형 (Fc ${\gamma}R$ composite genotype)을 확인하여, 각 군 간을 비교하였다. 치주질환의 특성과 유전자 다형성과의 관련성을 알아보기 위하여 Fc ${\gamma}R$ 유전자에 대한 유전자다형성을 조사한 결과 다음과 같은 결과를 얻을 수 있었다. 1. Fc ${\gamma}RIIla$에 대한 유전자다형성 연구결과 대조군과 severe CP, AgP군 사이에서, severe CP와 AgP군 사이에서는 대립유전자분포가 서로 유의성 있는 차이를 나타내었지만(p<0.05), Fc ${\gamma}RIIlb$에서는 유의성 있는 차이를 보이지 않았다(p>0.05). 2. Fc ${\gamma}R$ 복합유전자형간의 비교에서 유의성 있는 차이를 발견할 수 없었다(p>0.05). 이와 같은 결과를 종합하여 볼 때 실험대상 한국인 치주염환자에서 Fc ${\gamma}R$ 유전자에 대한 다형성분석에서 Fc ${\gamma}RIIIa$ 대립유전자가 치주염에 대한 감수성과 관련되어 있다고 생각된다. 이 연구의 결과는 유전자의 차이가 치주질환의 감수성 판단의 자료로 활용할 수 있는 가능성을 보여주고 있다.