• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.3C
• /
• pp.141-148
• /
• 2010

Electrical noises like self potential, burst noises and 60-Hz electrical noises are one of the causes to reduce reliability of electrical resistivity survey. Even the PDC-R (Pseudo DC resisitivity) technique, recently developed, is suffering from the problem of low reliability due to electrical noises. That is, both DC-based and AC-based resistivity technique is subject to reliability problem due to electrical noises embedded in urban geotechnical sites. In this research, a new technique to enhance reliability of the PDC-R technique by minimizing influence of electrical noises was proposed. In addition, an automated procedure was also proposed to facilitate data analysis and interpretation of PDC-R measurements. The proposed technique is composed of two steps: 1. to extract information only related with the input current by means of multiple-filter technique, and 2. to undertake a task to sort out signal information only to show stable and reliable characteristics. This automated procedure was verified by a synthetic harmonic wave including DC shift, burst random noises and 60-Hz electrical noises. Also the procedure was applied to site investigation at urban areas for proving its feasibility and accuracy.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.10
• /
• pp.1827-1832
• /
• 2017

To observe the characteristics to be a resistive memory of $V_2O_5$ deposited by oxygen various gas flows and annealed, the hysteresis curves of $V_2O_5$ were analyzed. The good resistive memory was obtained from the electrical characteristics of $V_2O_5$ films with the Schottky contact as a result of electron-hole pair, and the oxygen vacancy generated from the annealing process contributes the high quality of Schottky contact and the formation of resistive memories. The balanced Schottky contacts owing to the oxygen vacancy effect as the result of an ionic reaction were formed at the $V_2O_5$ film annealed at $150^{\circ}C$ and $200^{\circ}C$ and the balanced Schottky contact with negative to positive voltages enhanced the electrical operation with write/erase states according to the forward or reverse bias voltages for the resistive memory behavior due to the oxygen vacancy.

• Clinical and Experimental Pediatrics
• /
• v.46 no.8
• /
• pp.751-757
• /
• 2003

Purpose : Obesity is a significant health problem with medical and psychological consequences for children and adolescents. The purpose of this study was to assess the correlation between body fat percent using bioelectrical impedance(BI) and other variable methods. Methods : We measured height, weight, body mass index(BMI) and body fat percent by skinfold thickness(ST) and BI in 1,035(496 male; 539 female) children from seven to 18 years of age. The correlation coefficients between BI and each of the other different methods were obtained. The sensitivity and specificity to predict obesity by these several methods were studied. Results : Fat percent estimated by BI analysis and BMI showed a strong correlation(r=0.749). Fat percent estimated by BI analysis and ST showed a very strong correlation(r=0.835). At the 95th percentile cut-off point for BI, ST showed a sensitivity of 57.7%, and a specificity of 97.6% for estimating body fat. At the 95th percentile cut-off point for BI, BMI showed a sensitivity of 84.9%, and a specificity of 99.3% for estimating body fat. Conclusion : The fat percent estimated by BI analysis correlated strongly with ST or BMI. BI analysis is an objective and accurate method for estimating body fat in childhood obesity.

• Geophysics and Geophysical Exploration
• /
• v.22 no.3
• /
• pp.160-167
• /
• 2019

Resistivity inversion result may be distorted if the seepage line fluctuation within central core with the change of reservoir water level as well as the conductivity of the reservoir water is not taken into consideration because the reservoir dike is composed of three-dimensional (3D) resistivity structure. Consequently, to accurately analyze the resistivity changes inside the reservoir dike according to the change of reservoir water level, 3D electrical resistivity modeling for the 2D survey line considering topography and physical properties of dam components was carried out. In addition, 2D inversion was performed with the simulated 2D resistivity data for a given 3D model in order to compare it with the inversion result of real field data. For 283 reservoirs in Korea, 2D inversion results for the simulated 2D data and field 2D resistivity data were compared. Finally, the reservoirs with an inversion ratio of 50% or less were selected as reservoirs that require further precise investigation.

• The Journal of Engineering Geology
• /
• v.31 no.2
• /
• pp.187-197
• /
• 2021

Clay mineral content of weathered zone is a key parameter for landslide studies. Electrical resistivity tomography is usually performed to delineate the geometry of complex landslides and to identify the sliding surface. In clay-bearing weathered zone, parallel resistivity Archie equation is employed to investigate the effect of conductivity added (resistivity reduced) by clay minerals of kaolinite and montmorillonite, which is dependent on their specific surface area and cation exchange capacities (CEC). A decrease of overall resistivity and apparent formation factor is observed with increasing pore-water resistivity, significantly in montmorillonite. Formation factor is found decreased with increasing porosity and decreasing cementation factor. Parallel Archie equation was applied to the electrical resistivity data from the test area (Sinjindo-ri, Taean-gun, Chungcheongnam-do, Korea) which experienced land creeping in the year of 2014. A panel test with varying clay-mineral contents provides the best fit section when the theoretical section constructed with the assumed contents approaches the field section, from which the clay-mineral content of the weathered zone is estimated to be approximately 10%. Resistivity interpretation schemes including the clay mineral contents for land creeping studies explored in this paper can be challenged more when porosity, saturation, and pore-water resistivity are provided and they are included in the numerical resistivity modeling.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 1999.06a
• /
• pp.249-252
• /
• 1999

전도성 충진제가 포함된 결정성 고분자내에 대전류가 흐르게 될 경우 Joule 효과로 소재자체의 발열현상이 발생하며 온도가 증가함에 따라 고분자의 용융점 부근에서 급격한 열팽창으로 인하여 고분자 내에 분포되어 있던 전도성 충진재 입자사이의 간격이 증가하게 되며 전자들의 흐름이 방해를 받게 된다. 이에 따라 전기저항이 커져 전류의 흐름이 감소되는 철상이 발생하며 이를 PTC(Positive Temperature Coefficient)라 하고 온도 증감에 따른 전도성 충진제 간의 electron tunnelling과 고분자의 결정변화에 의해 민감한 전기저항변화 특성을 나타낸다. (중략)

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.6
• /
• pp.122-129
• /
• 2013

Since electrical resistivity of concrete can be measured in a more rapid and simple way than chloride diffusivity, it should be primarily regular quality control of the electrical resistivity of concrete which provides the basis for indirect of quality control of chloride diffusivity during concrete construction. If this is realized, the electrical resistivity of concrete can be a crucial parameter to establish maintenance strategy for marine concrete structures. The purpose of this study is to develop, design and test a surface electrical resistivity measurement protocol. Microstructural affecting factors such as capillary water, porosity, tourtousity, and so on, on the electrical resistivity of concrete were examined taking into account for mixing proportion properties, and hydration stage. This study can provide a non-destructive approach for durability design of marine concrete. From the relationship between electrical resistivity and chloride diffusivity, it is expected that the result is subsequently used as a calibration curve for an indirect control of the chloride diffusivity based on regular measurements of the electrical resistivity during concrete construction.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.32.1-32.1
• /
• 2009

현재 ITO를 대체할 재료로 투명 전도성 탄소나노튜브(carbon nanotube, CNT) 필름에 대한 연구가 진행 되고 있다. 이러한 연구에서 특히 CNT 필름의 투과도에 따른 전기저항을 향상시키기 위한 연구가 활발히 진행되고 있다. 본 연구에서는 단일벽 CNT (single-walled CNT)를 여러 가지 계면활성제로 최적 분산시킨 수용액으로부터 제조한 CNT 필름의 투과도에 따른 면 저항 (sheet resistance) 변화를 관찰하였다. 우선 계면활성제로 분산시킨 CNT 수용액을 알루미나 재질의 필터에서 정량적으로 진공 필터링하여 CNT 필름을 제조하였다. 알루미나 필터를 sodium hydroxide (NaOH) 수용액으로 용해시켜 제거함으로써 얻은 CNT 필름을 유리기판 위에 부착시켰다. 필름의 전기저항을 낮추기 위해 유리기판 위에 부착된 CNT 필름을 질산 (HNO3) 용액으로 처리하였다. Scanning electron microscopy, UV-Vis spectroscopy를 이용하여 각각 필름의 형상과 광 투과도를 분석하였고, 4-point probe로 면 저항을 측정하였다. 계면활성제로 분산시킨 CNT 필름 대부분의 면 저항은 질산 처리에 의해 감소하였다. 이는 CNT 표면에 코팅되어 있던 계면활성제가 질산에 의해 제거되었기 때문인 것으로 예상된다. 여러 계면활성제 중 sodium dodecyl benzenesulfonate로 분산시킨 CNT 필름이 산 처리 후에 가장 낮은 면 저항을 보였다. 그리고 Polyvinyl pyrrolidone (PVP)과 cetyltrimethylammonium bromide (CTAB)를 사용하여 제조한 CNT 필름의 면 저항이 가장 뚜렷한 감소를 보였다.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1716-1717
• /
• 2011

잉크젯으로 인쇄된 실버 나노입자가 오븐, 레이저, 전기를 이용한 소결방법에 의해 소결되었다. 전도성 라인은 드롭 온 디맨드형(drop-on-demand) 잉크젯 프린터에 의해 유리 기판 위에 인쇄되었다. 레이저를 이용한 소결은 레이저 강도와 조사시간을 변화시키면서 실버나노입자를 소결하였고, 전기 소결은 인쇄된 라인에 정전류 방식을 이용하여 인가해주는 전류값을 변화시키면서 소결하였다. 소결방법에 따른 비저항변화, 단면적 변화, 미세구조변화를 관찰하였고 이 결과를 오븐 소결 결과와 비교하였다. 전기를 이용하여 소결하였을 경우 가장 낮은 비저항을 얻을 수 있었고, 은의 고유 비저항에 비하여 1.7배 큰 비저항을 얻었다.

• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.3
• /
• pp.45-50
• /
• 1999

Copper has been widely used for the electronic parts, and especially spot welded one for the leads of condenser or resistor. However, copper is generally hard to be spot welded because of its low electrical resistivity. For this experiment, Sn-37%Pb solder which has relatively higher resistivity was coated on the Cu-sheet to improve the spot weldability of copper. As the experimental variables welding pressure was varied from 100 to 200kgf, welding time from 20 to 50ms, and welding current from 100 to 2500A. Experimental results showed that the solder coated Cu-sheet can be spot welded under the conditions of 400~2200A welding current, 100~200kgf pressure and 20-50ms welding time. The tensile shear strength of the spot welded joint increased with welding current up to the critical current, and after the critical value decreased with current.