• Korean Journal of Optics and Photonics
• /
• v.14 no.1
• /
• pp.38-43
• /
• 2003

Fabrication process of strain-induced channel waveguides in $LiNbO_3$ was developed using strain-optic effect and compressional strain due to ~1.4 $\mu\textrm{m}$ surface Mo/Pt metal film. Characterization of the channel waveguides revealed a single transverse and depth mode in both TE and TM polarizations. Measurements showed total insertion loss of 6.2 and 7.7 ㏈/cm for TM and TE polarizations. respectively. Electro-optic intensity modulators with 11 mm long electrode length and 21 $\mu\textrm{m}$ electrode gap at $\lambda$ = 1.15 ${\mu}{\textrm}{m}$have been produced in $LiNbO_3$ substrates using strain-induced channel waveguides. Modulation depth of 100% at $\pi$-radian voltage of 16.1V has been demonstrated. Also, 1$\times$2 on/off power splitters at $\lambda$ = 0.63 $\mu\textrm{m}$ have been produced using strain-induced channel waveguides. On/off voltage of $\pm$ 25V has been demonstrated.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.16 no.2
• /
• pp.121-129
• /
• 2002

The present paper describes a technique for installing an effective grounding grids, the major objective is forced on the experimental evaluation of the performance and characteristics with the arrangement and installation method for grounding grids consisting of the means to protect electric shock, electronics and computerized facilities against lightning, switching and ground fault surges. The study is oriented on two major areas: (1) the analysis of the ground surface potential gradient with the arrangement of grounding grids, (2) the control of the dangerous ground surface potential rise. The experiments wee carried out with the impulse currents as a function of the installation method or arrangement of grounding grids. An installation method of the inclined auxiliary grounding grid was proposed to overcome the drawbacks of equally spared grounding grids, i.e. an appropriate design concept far the installation of grounding grids was found out, It has been shown that the installation of the intwined auxiliary grounding grid can also result in a mere than 50% decrease in the maximum potential gradient on the ground surface and enhance the level of safety for persons and electronic equipments..

• Economic and Environmental Geology
• /
• v.36 no.6
• /
• pp.501-510
• /
• 2003

Several geophysical surveys(electrical resistivity, electromagnetic, seismic refraction, CPR) were conducted to primarily investigate the gallery and the geomembrane at an abandoned mine(Imcheon mine). The subsurface structure mapped from seismic refraction survey mainly consists of three velocity layers(>1000 m/s, 1000∼2000 m/s,＜2000 m/s). Top of the bedrock, whose velocities exceed 2000 m/s, appears to be at depth of 7.5∼10m. Higher resistivities (of ten thousands-hundred of thousands ohm-m) are interpreted to be associated with a open(cavities) gallery. The events at depth of approximately 0.5∼0.7m in GPR sections are probably caused by high-density-poly-ethylene geomembrane. Taking into consideration of the differences in the spatial resolution between georadar and electrical surveys, the events of geomembrane correspond to the top of the high resistivities at depth of about 2m. The segments, characterized with the higher conductivities in the electromagnetic data and the lower resistivities in the electrical resistivity data, are probably associated with surface water or tear zone of geomembrane.

• Applied Chemistry for Engineering
• /
• v.25 no.4
• /
• pp.386-391
• /
• 2014

Atmospheric-pressure nonthermal corona discharge plasma was applied to the sterilization of biologically contaminated scoria powder. Escherichia coli (E. coli) culture solution was uniformly sprayed throughout the scoria powder for artificial inoculation, which was well mixed to ensure uniformity of the batch. The effect of the key parameters such as discharge power, treatment time, type of gas and electrode distance on the sterilization efficiency was examined and discussed. The experimental results revealed that the plasma treatment was very effective for the sterilization of scoria powder; 5-min treatment at 15 W could sterilize more than 99.9% of E. coli inoculated into the scoria powder. Increasing the discharge power, treatment time or applied voltage led to an improvement in the sterilization efficiency. The effect of type of gas on the sterilization efficiency was in order of oxygen, synthetic air (20% oxygen) and nitrogen from high to low. The inactivation of E. coli under the influence of corona discharge plasma can be explained by cell membrane erosion or etching resulting from UV and reactive oxidizing species (oxygen radical, OH radical, ozone, etc.), and the destruction of E. coli cell membrane by the physical action of numerous corona streamers.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.523-523
• /
• 2013

대기압 제트 플라즈마는 의료산업 및 재료공정, 정수, 기체흐름 제어 등 다양한 분야에 적용을 위한 연구가 활발히 진행되고 있다. 뿐만 아니라 구동 조건에 따라 다양한 방전 모드가 존재하며, 이에 따라 발생된 플라즈마의 광학적 및 전기적 특성도 매우 다르게 나타나기 때문에 과학적으로도 새로운 현상들이 속속 발표되고 있다. 대기압 제트 플라즈마에서 중요한 과학적 현상 중 하나인 스트리머(streamer) 혹은 플라즈마 총알(plasma bullet)은 수-수십 kHz의 저주파 전압으로 구동 시 특정 조건에서 발생하는 현상으로, 최근 들어 시간분해능이 높은 ICCD 카메라를 이용하여 스트리머의 발생 및 전파에 대한 새로운 현상의 발견과 다양한 물리적 이해가 시도되고 있다. 본 연구에서는 헬륨 대기압 제트 플라즈마에 포함된 질소 함유량에 따른 다중 스트리머의 발생 및 기작의 이해를 시도하였다. 구동 전압 및 주파수, 헬륨기체의 유량, 전극 구조 및 간격 등 모든 조건이 동일한 상태에서 질소기체의 함유량을 증가시킬수록 특정 영역에서 스트리머의 개수가 증가하는 것을 관찰되었다. 또한 $N_2{^+}$의 방출광 세기가 헬륨 및 산소 원자의 방출광보다 지배적인 것으로 측정되었으며, 이는 헬륨 플라즈마에서 흔히 나타나는 헬륨 metastable에 의한 질소분자의 페닝 이온화(Penning ionization) 때문이다. 본 연구팀은 페닝 이온화($He^*+N_2{\rightarrow}He+N_2{^+}+e$)로 인해 추가적으로 발생하는 전자가 다중 스트리머 발생에 중요한 역할을 하는 것이라 제안한다. 좀 더 심화적인 분석을 하고자 헬륨-질소 플라즈마에서 주된 여러 가지 반응식을 이용하여 페닝 이온화에 의한 이온화율 및 전자의 직접적인 충돌에 의한 질소, 헬륨의 이온화율의 계산을 수행하여 특정 영역에서 헬륨의 이온화율보다 질소 페닝 이온화율이 더 커지는 것을 확인하였다.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.5
• /
• pp.543-548
• /
• 2006

This paper is to be researched into ozone generation character of Bi-Ti-Si type high dielectric ceramic catalyst discharge tube. And conditions of basic experiment are the outside diameter of discharge tube : 52 mm, the length of discharge tube : 350 mm, the frequence : 900 Hz, the temperature of cooling water : $25^{\circ}C$, quantity of flow : 5, 10, 20 L/min, pressure : 1.2, 1.4, 1.6 atm, and distance of discharge gap : 0.4, 0.6, 0.8 mm. Ozone generation characteristics were measured to consumption power. At quantity of flow : 20 L/min, discharge gap : 0.6 mm, pressure : 1.6, and consumption power : 150 W, Maximum ozone generation efficiency of 175 g/kWh was obtained. And a range of maximum ozone generation efficiency was measured below the flow quantity of 20 L/min at below pressure of 1.6 atm. However, Maximum ozone generation efficiency was measured over the flow quantity of 20 L/min at over pressure of 1.6 atm.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.63 no.4
• /
• pp.301-306
• /
• 2014

Recently in accordance with the rapid development of the industrial society, the accidents caused by dielectric breakdown have been increasing in power grid. It is important to prevent the dielectric breakdown of a high voltage apparatus to reduce the damage from electrical hazards. To establish an electrically reliable database of insulation design criteria for high voltage apparatus, a study on dielectric characteristics test is indispensable. In this study, dielectric characteristics according to field utilization factors (${\xi}$) which are represented as the ratio of mean electric field to maximum electric field are investigated. the dielectric breakdown experiments by using several kinds of electrode systems made with stainless steel are performed by AC breakdown voltage under air-insulation. Also, the experimental results are analyzed by the Weibull distribution. As a result, it is found that the dielectric characteristics of air-insulation are determined by ${\xi}$ as well as arrangement of electrode systems. It is considered that the results of this study would be applicable to designing the air-insulated high voltage apparatuses.

• Resources Recycling
• /
• v.18 no.3
• /
• pp.62-68
• /
• 2009

Continuous operation for 24h was carried out to establish the optimum condition at the magnesium fused salt electrolysis using a self made 150 ampere mono-polar type cell. An electrolyte composition of $MgCl_2$ 25%, NaCl 55%, $CaCl_2$ 19%, $CaF_2$ 1% was electrolyzed with applied voltage 7V, cathode current density $0.7-0.75A/cm^2$, electrode distance 6cm at $720{\sim}740^{\circ}C$ for 24 hours. Changes of applied current, composition of the electrolyte, current efficiency were investigated. Through the experiments, there were not any operating troubles with the self-made electrolytic cell. Purity of the electrolyzed magnesium metal was above 99%, and 89% of current efficiency was achieved. Some basic data for scale-up of the magnesium electrolysis equipment which would be necessary for commercialization were obtained.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.9
• /
• pp.62-71
• /
• 2002

An intergral C-V converter is proposed to solve the nonlinearity problem of capacitive pressure sensors. The integral C-V converter consists of a switched-capacitor integrator and a switched-capacitor differential amplifier. It converts the sensor capacitance change which is inversely proportional to an applied pressure into a linear voltage output. Various PSPICE simulations prove that the convertor has excellent characteristics, such as low nonlinearity less than 0.01%/FS and low sensitivity to parallel offset capacitance and parasitic capacitance for the displacement range of sensor diaphragm set to 0 ${\sim}$ 90% of the initial distance between the electrodes in the simulation. We also show that the offset compensation and the gain trimming are easily achieved with the integral C-V converter.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.8
• /
• pp.1767-1775
• /
• 2003

The SAW device is extensively used as a electro$.$mechanical band­pass filter in which a two­pairs of interdigital transducers are provided over the surface of the piezoelectric substrate. For the design requirement, the central frequency and the bandwidth of the passband, and the attenuation level of the stopband region are specified. The configuration is made so as to satisfy the specification given. The central frequency is mainly determined by the distance between the pair of the finger electrodes. The design is considered as an optimization problem with which the error norm, the distance between the desired characteristics and the calculated for a given model is to be minimized. The delta function model and the electrical equivalent circuit model are utilized to represent the SAW filter characteristics. Genetic algorithm is used for optimization in which apodization of the transducer fingers is chosen as a design variable.