• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.613-613
• /
• 2013

그래핀은 저차원계 구조에서 기인하는 뛰어난 전기적, 물리적, 기계적 성질을 지니고 있어 실리콘 기반 기술을 대체할 전계 효과 트랜지스터 이외에도 투명전극, 초고용량 커패시터, 전계방출 디스플레이 등 다양한 응용분야에 적용 가능하다. 최근에는 이러한 응용 연구분야에서 그래핀과 탄소나노튜브 각각의 단점을 최소화하고 장점을 극대화하기 위한 그래핀-탄소나노튜브 혼성 나노구조에 대한 연구들이 진행되고 있는 추세이다. 이전 연구들에서 환원된 그래핀 산화물(Reduced Graphene Oxide, RGO)을 이용한 그래핀-탄소나노튜브 혼성 나노구조가 제작되었는데, 이는 RGO의 제작과정에서 복잡한 공정과 긴 합성과정이 요구될 뿐 아니라, 복합 물질에서 탄소나노튜브의 밀도 제어가 어렵다는 단점을 지닌다. 또한 현재까지 제작된 그래핀-탄소나노튜브 혼성 나노구조의 경우, 열 화학기상증착법으로 합성된 다층(few-layers)의 그래핀과 탄소나노튜브 혼성 나노구조를 제작하였다 [1-6]. 본 연구에서는 우수한 전기적 특성을 가진 단층(monolayer)의 그래핀을 열 화학기상증착법으로 합성한 후, 그래핀 위에 단일벽 탄소나노튜브를 성장시킴으로써 그래핀-탄소나노튜브 혼성 나노구조를 제작하였다. 합성된 그래핀-탄소나노튜브의 구조적 특징은 주사 전자 현미경과 라만 분광기 측정을 통해 확인하였고, 촉매의 표면 형상 및 화학적 상태는 원자힘 현미경과 X선 광전자 분광법을 통해 확인하였다. 또한 그래핀 기반의 전계 효과 트랜지스터의 경우, 상온에서 그래핀은 우수한 전하 이동도를 가지며 웨이퍼 스케일에서 제작하기 쉬우나 밴드 갭이 없으므로 높은 Ion/Ioff를 가지는 그래핀 기반의 트랜지스터를 만드는 것이 과제이다. 반면 탄소나노튜브는 큰 에너지 갭을 가지고 있으므로 높은 Ion/Ioff를 구현하는 소자 제작이 가능하다. 그리하여 제작된 그래핀-탄소나노튜브 혼성 나노구조의 소자 제작을 통해 전기적 특성을 조사하였다.

• Membrane Journal
• /
• v.26 no.2
• /
• pp.141-145
• /
• 2016

Polymer electrolyte membranes (PEMs) are key components to determine electrochemical fuel cell performances, in addition to electrode materials. The PEMs need to satisfy selective transport behaviors to small molecules including gases and protons; the PEMs have to transport protons as fast as possible, while they should act as hydrogen barriers, since the permeated gas induces the thermal degradation of cathode catalyst, resulting in rapid electrochemical reduction. To date, limited tools have been used to measure how fast hydrogen gas permeates through PEMs (e.g., Constant volume/variable Pressure (time-lag) method). However, most of the measurements are conducted under vacuum where PEMs are fully dried. Otherwise, the obtained hydrogen permeance is easily changeable, which causes the measurement errors to be large. In this study, hydrogen permeation properties through Nafion212 used as a standard PEM are evaluated using an in-situ measurement system in which both temperature and humidity are controlled at the same time.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.5
• /
• pp.543-548
• /
• 2006

This paper is to be researched into ozone generation character of Bi-Ti-Si type high dielectric ceramic catalyst discharge tube. And conditions of basic experiment are the outside diameter of discharge tube : 52 mm, the length of discharge tube : 350 mm, the frequence : 900 Hz, the temperature of cooling water : $25^{\circ}C$, quantity of flow : 5, 10, 20 L/min, pressure : 1.2, 1.4, 1.6 atm, and distance of discharge gap : 0.4, 0.6, 0.8 mm. Ozone generation characteristics were measured to consumption power. At quantity of flow : 20 L/min, discharge gap : 0.6 mm, pressure : 1.6, and consumption power : 150 W, Maximum ozone generation efficiency of 175 g/kWh was obtained. And a range of maximum ozone generation efficiency was measured below the flow quantity of 20 L/min at below pressure of 1.6 atm. However, Maximum ozone generation efficiency was measured over the flow quantity of 20 L/min at over pressure of 1.6 atm.

• Journal of Hydrogen and New Energy
• /
• v.27 no.6
• /
• pp.677-684
• /
• 2016

Various commercially available gas diffusion layers (GDLs) from different manufacturers were used to prepare an air electrode using $La_{0.8}Sr_{0.2}CoO_3$ perovskite (LSCP) as the catalyst for the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) in an alkaline solution. Various GDLs have different physical properties, such as porosity, conductivity, hydrophobicity, etc. The ORR and OER of the resulting cathode were electrochemically evaluated in an alkaline solution. The electrochemical properties of the resulting cathodes were slightly different when compared to the physical properties of GDLs. Pore structure and conductivity of GDLs had a prominent effect and their hydrophobicities had a minor effect on the electrochemical performances of cathodes for ORR and OER.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.160-161
• /
• 2008

$SnO_2$는 n형 반도체로써 3.6 eV의 큰 밴드갭을 가지는 물질로 CO와 NOx 가스에 좋은 감도를 나타내는 것으로 보고되고 있다. 문헌에 따른 일반적인 $SnO_2$ 가스센서는 후막이나 벌크형태로 제작되었다. 근래에는 가스감응체가 $SnO_2$ 나노선 형태인 가스센서가 활발한 연구 중에 있다. 본 논문에서는 기판 위에 서로 분리된 전극 패턴에 Au를 촉매로 하여 네트워크 구조로 된 $SnO_2$ 나노선이 합성되었다. 제작된 가스센서에 Pd 도핑에 따른 영향을 알아보기 위하여 1.8 mM의 Pd 용액 ($PdCl_2{\cdot}xH_2O$ 3 mg + $H_2O$ 10 ml)을 이용하여 센서에 도핑하였다. 측정 시스템에서 $NO_2$ 가스에 대한 센서의 특성을 분석한 결과 도핑하지 않은 $SnO_2$ 센서보다 20%정도의 감도가 개선되었다.

• Clean Technology
• /
• v.20 no.1
• /
• pp.88-94
• /
• 2014

During the past decades much attention has been paid to the desulfurization of diesel oil which is important as a source for the fuel cells to prevent the sulfur poisoning of both diesel steam reforming catalyst and electrode of fuel cell. Although alternative desulfurization techniques have been investigated, desulfurization for ultra-low sulfur diesel (ULSD) is still challenged. Therefore, this research focuses on the desulfurization of commercial ULSD for the application to molten carbonate fuel cell (MCFC). Herein, the performances of several kinds of commercial adsorbents based on activated carbons, zeolites, and metal oxides for desulfurization of ULSD were screened. The results showed that metal oxides based materials can feasibly reduce sulfur concentration in ULSD to a level of 0.1 ppmw while activated carbons and zeolites did not reach this level at current conditions.

• Journal of Adhesion and Interface
• /
• v.16 no.4
• /
• pp.152-155
• /
• 2015

Platinum (Pt) is an easily moldable, anti-corrosive and also good catalyst in a variety of chemical reactions. Platinum can be used in many fields, however, however, the low wettability of platinum substrate in many platinum-based devices has been made a problem when they contact with liquid state environment. In this study, we report a simple and effective self-assembled monolayer coating method which provides tremendously increased wettability on platinum substrate device by using Sodium 3-mercapto-1-propanesulfonic acid solution. After surface modifications, water contact angle of the surfaces displayed less than $10^{\circ}$, representing that surfaces are successfully coated to be super-hydrophilic surface by simple dip coating method.

• Membrane Journal
• /
• v.26 no.5
• /
• pp.329-336
• /
• 2016

Proton exchange membrane (PEM) is one of the key components of membrane-electrode assembly (MEA), which plays important role in fuel cell performance together with catalysts. It is widely accepted that water channel morphology inside PEMs as a proton pathway significantly affects the PEM performance. Molecular dynamics (MD) simulations are a very useful tool to understand molecular and atomic structures of materials, so that many related researches are currently being studied. In this paper, we summarize the current research trend in MD simulations, present which properties can be characterized, and finally introduce the usefulness of MD simulations to the researchers for proton exchange membranes.

• Journal of Hydrogen and New Energy
• /
• v.27 no.3
• /
• pp.276-282
• /
• 2016

The effects of conductive additives in a $La_{0.8}Sr_{0.2}MnO_3$ perovskite bifunctional electrode for oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) were investigated in an alkaline solution. Highly porous carbon black (CB) and Ni powder were added to the bifunctional electrodes as conductive additives. The surface morphologies of electrodes containing CB and Ni were observed by scanning electron microscopy (SEM). The current densities for both ORR and OER were changed by the addition of CB. The conductive additive changed physical properties of bifunctional electrodes such as the sheet conductance, gas permeability and contact angle. It was observed that the air permeability of electrode was most effective to enhance the currents for ORR and OER.

• Journal of the Korean Electrochemical Society
• /
• v.9 no.3
• /
• pp.118-123
• /
• 2006

Degradation of polymer electrolyte membrane fuel cell (PEMFC) that is facilitated by on/off cycles is one of the most important issues for commercialization of fuel cell vehicles. When a PEMFC stack is shut down, residual hydrogen and induce high voltage equivalent to open circuit voltage to the cathode side that might cause sintering of Pt catalyst and facilitate formation of hydrogen peroxide at the anode side that might decompose $Nafionc\'{A}$ membrane. In this study, degradation of PEMFC exposed to repetitive on/off cycles was investigated by measuring i-V characteristics, ac impedance, cyclic voltammograms, gas leak, cross-sectional SEM images, and TEM images. To prevent degradation of PEMFC caused by the residual gases, hydrogen was removed from anode gas channel by gas-purging and by using a dummy resistance, that were found to be a very effective method.