• Journal of Korea Water Resources Association
• /
• v.52 no.4
• /
• pp.301-312
• /
• 2019

The importance of the dual drainage system model has increased as the urban flood damage has increased due to the increase of local storm due to climate change. The dual drainage model is a model for more accurately expressing the phenomena of surface flow and conduit flow. Surface runoff and pipe runoff are analyzed through the respective equations and parameters. And the results are expressed visually in various ways. Therefore, inundation analysis results of dual drainage model are used as important data for urban flood prevention plan. In this study, the applicability of the COBRA model, which can be interpreted by combining the dual drainage system with the natural watershed and the urban watershed, was investigated. And the results were compared with other dual drainage models (XP-SWMM, UFAM) to determine suitability of the results. For the same watershed, the XP-SWMM simulates the flooding characteristics of 3 types of dual drainage system model and the internal flooding characteristics due to the lack of capacity of the conduit. UFAM showed the lowest inundation analysis results compared with the other models according to characteristics of consideration of street inlet. COBRA showed the general result that the flooded area and the maximum flooding depth are proportional to the increase in rainfall. It is considered that the COBRA model is good in terms of the stability of the model considering the characteristics of the model to simulate the effective rainfall according to the soil conditions and the realistic appearance of the flooding due to the surface reservoir.

• Journal of Wetlands Research
• /
• v.20 no.4
• /
• pp.314-321
• /
• 2018

In order to quantify nonpoint source pollution, it was proposed to sample at regular intervals of 1 hour for the first 24 hours of storm runoff process by National Institute of Environmental Research for the mixed landuse watershed. However, high frequency sampling requires intensive laboratory analysis and labor costs. In order to investigate the effect of longer sampling interval on the load estimation compared to the 1 hour sampling method, analysis was conducted using monitoring data from rural subwatershed, urban subwatershed, and outlet of the Pungyeongjeongcheon watershed. Statistical analysis revealed that mean of load estimation was not significantly different up to 4 hour sampling frequency. However, 3 hour sampling interval was found to be appropriate for the BOD and TP when it is judged that 10% or less of the difference in loading amount between the 1 hour and other sampling interval is reasonable. The results of this study can be used to conduct an effective monitoring system.

• Journal of the Korean Society of Radiology
• /
• v.12 no.7
• /
• pp.879-886
• /
• 2018

A 3-dimensional (D) printer is a device capable of outputting a three-dimensional solid object based on data modeled in a computer. These features are utilized in the bone model X - ray phantom production etc using CT data by fusing with the radiation science field. A bone model phantom was made using data obtained by CT scan of an existing Pelvis phantom, using PLA, Wood, XT-CF20, Glow fill, Steel filaments which are materials of Fused Filament Fabrication (FFF) 3D printer.Measure Hounsfield Unit (HU) with images obtained by CT scan of the existing Pelvis phantom and five material phantoms made with 3D printer under the same conditions,SI and SNR were measured using a diagnostic X-ray generator, and each phantom was compared and analyzed.As a result, the X - ray phantom in the X - ray examination condition of the limb was found to be most suitable for the glow fill filament.The characteristics of the filament can be known to the base of this research and the practicality of X - ray phantom fabrication was confirmed.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.6
• /
• pp.1301-1308
• /
• 2018

90/150 CA which are used as key generators of the cipher system have more randomness than LFSRs, but synthesis methods of 90/150 CA are difficult. Therefore, 90/150 CA synthesis methods have been studied by many researchers. In order to synthesize a suitable CA, the analysis of the characteristic polynomial of 90/150 CA should be preceded. In general, the characteristic of polynomial ${\Delta}_n$ of n cell 90/150 CA is obtained by using ${\Delta}_{n-1}$ and ${\Delta}_{n-2}$. Choi et al. analyzed $H_{2^n}(x)$ and $H_{2^n-1}(x)$, where $H_k(x)$ is the characteristic polynomial of k cell 90/150 CA with state transition rule <$10{\cdots}0$>. In this paper, we propose an efficient method to obtain $H_n(x)$ from $H_{n-1}(x)$ and an efficient algorithm to obtain $H_{2^n+i}(x)$ and $H_{2^n-i}(x)$ ($1{\leq}i{\leq}2^{n-1}$) from $H_{2^n}(x)$ by using this method.

• Journal of the Korean Geotechnical Society
• /
• v.34 no.12
• /
• pp.105-113
• /
• 2018

In this study, the engineering properties including bearing capacity of subgrades stabilized with a binder are analyzed by laboratory and field experiments. The main components of the binder are CaO and $SO_3$. After the binder was mixed with a low plasticity clay, the passing rates were relatively decreased as the sieve mesh size increased. Not only did the soil type change to silty sand, but engineering properties, such as the plasticity index and modified California bearing ratio (CBR), were improved for the subgrade. A comparison of the compaction curves of the stabilized subgrade and field soil compacted with the same energy demonstrated an increase of approximately 6% in the maximum dry unit weight, slight decrease in optimum moisture content, and considerable increase improvement in grain size. In the modified CBR test, the effect of unit weight and strength increase of the modified soil (with a specific amount of binder) was remarkably improved. As the proportion of granulated material increased after the addition of binder, the swelling was reduced by 3.3 times or more during initial compaction and 6.5 times by final compaction. The unconfined compressive strength of the specimens was maintained at the homogeneous value with a constant design strength. The stabilized subgrade was validated by applying it in the field under the same conditions; this test demonstrated that the bearing capacity coefficients at all six sites after one day of compaction exceeded the target value and exhibited good variability.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.1
• /
• pp.339-346
• /
• 2019

Various studies have been conducted to evaluate the probabilistic fatigue life of steel railway bridges, but many of them are based on a relatively simple model of crack propagation. The model assumes zero minimum stress and constant loading amplitude, which is not appropriate for the fatigue life evaluation of railway bridges. Thus, this study proposes a new probabilistic method employing an advanced crack propagation model that considers the live-dead load ratio for the fatigue life evaluation of steel railway bridges. In addition, by using the rainflow cycle counting algorithm, it can handle variable-amplitude loading, which is the most common loading pattern for railway bridges. To demonstrate the proposed method, it was applied to a numerical example of a steel railway bridge, and the fatigue lives of the major components and structural system were estimated. Furthermore, the effects of various ratios of live-dead loads on bridge fatigue life were examined through a parametric study. As a result, with the increasing live-dead stress ratio from 0 to 5/6, the fatigue lives can be reduced by approximately 30 years at both the component and system levels.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.38 no.4
• /
• pp.286-290
• /
• 2018

This study was carried on comparison of forage yields and growth of cropping system as forage (winter & summer) in Cheonan 2015~2016. The species of forage crop used were Barley (cv. Youngyang), Sorghum (cv. SX17), Proso millet (domestic) and Japanese millet (cv. Jeju). Plant height is the lowest when harvested in lough stage than in the harvests of all summer crops. The dry matter yield of lough stage was 1,343 kg/10a in barley. Looking at the dry matter according to cropping systems, the sorghum was higher at 10,018 kg when harvested at the lough stage than at the harvest. Dry matter of Proso millet and Japanese millet also had higher at the lough stage than at other harvest times. ADF content of sorghum was lower than that of harvesting, but Proso millet and Japanese millet showed higher ADF content in lough stage. The NDF content of the three crops was higher than that of the harvests, and crude protein content was higher in harvest than that of at lough stage. Total production of crude protein against dry matter yield was about 761 kg when sorghum was harvested at lough stage. There was no difference in the content of TDN among three crops according to harvesting time.

• Korean Journal of Optics and Photonics
• /
• v.29 no.6
• /
• pp.241-246
• /
• 2018

In this paper, a low-cost optical temperature sensor is implemented, using a fiber Bragg grating (FBG) as the temperature probe and a low-cost VCSEL with temperature-dependent output wavelength as the light source. To analyze the wavelength of the reflected light from the FBG, an interrogation was applied using a method of referring to the internal temperature according to the output wavelength of the VCSEL. When the temperature of the VCSEL was adjusted from 14 to $52.2^{\circ}C$, the output wavelength varied from 1519.90 to 1524.25 nm. The degree of wavelength tuning according to temperature was $0.114nm/^{\circ}C$. The variable wavelength repeatability error according to temperature was ${\pm}0.003nm$, and the temperature measurement error was ${\pm}0.18^{\circ}C$. As a result of measuring the temperatures from 22.3 to $194.2^{\circ}C$, the value of the internal temperature change of the light source according to the applied temperature ${\Delta}T$ was $0.146^{\circ}C/{\Delta}T$, the change in reflected wavelength of the temperature probe according to applied temperature ${\Delta}T$ was measured at $16.64pm/^{\circ}C$. and the temperature measurement error of the sensor was ${\pm}1^{\circ}C$.

• Journal of the Korean BIBLIA Society for library and Information Science
• /
• v.29 no.4
• /
• pp.91-111
• /
• 2018

This study was carried out on specialized library librarians to investigate the status and overall satisfaction of specialized services and to compare the degree of importance and satisfaction of specialized subject data, specialized service places, specialization programs, specialized subject area facilities and environment based on ISA technique in order to derive problems and improvement measures for the operation of specialized libraries. As results, first, it was found that a specialized library subject should be selected based on the characteristics, history, and resources of the library location as well as based on the demand survey of the local residents and users. Second, based on the appropriate program type of specialized subject and the results from users' demand surveys, specialized libraries should develop different types of experience-type, lecture-type, view-type and the likes. Third, specialized library space types can be divided into integrated type, independent-in-integration type, and independent type. Even though it is most ideal to provide independently specialized space, the space must be constructed considering the circumstances and subject of specialization of each library. Fourth, specialized libraries should have at least one dedicated specialist in the corresponding subject. Dedicated specialists should provide lending and reference services related to the specialization such as tidying, browsing, reading and operating specialized programs. And a dedicated specialist must be an expert in the specialized subject and also a librarian who is responsible of the general library operation.

• Journal of Advanced Navigation Technology
• /
• v.22 no.6
• /
• pp.530-536
• /
• 2018

Recently, many studies for interoperability of UAV in the NAS has been performed since the application range and demand of UAV are continuously increased. For the interoperation of UAV in the NAS, technical standards and certification system for UAV which is equivalent to the commercial aircraft are required and test and evaluation methodology must be presented by standards. In this paper, qualification test and evaluation methodology aboutfor the UAV navigation system is proposed. For the research, the mission profile and operation environment of UAV were analyzed. Thereafter the test criteria were derived and the test methodology were established. Finally, the simulation and demonstration using test-bed UAV were performed. As a result of the test, it was confirmed that the navigation system of test UAV has a position accuracy about 1.4 meters at 95% confidence level in the entire flight stage.