• The Journal of Engineering Geology
• /
• v.28 no.1
• /
• pp.101-115
• /
• 2018

This study was carried out to evaluate the effects of various filter conditions on unconfined aquifer (alluvial aquifer). We made model test device which has filter layer, pumping well and observation well which consist of sand layer and gravel layer to test. Step drawdown test and long term pumping tests were carried out using the device. The permeability characteristics of each test group were confirmed and the optimal yield was calculated. As a result of comparing the optimal yield of double filter and single filter in sand, dual-filter SD-300 was valued at 216.8 % higher final optimal yield than single-filter SS-300. Comparing the dual filter SD-300 and the single filter SS-100 with a thin filter layer, dual-filter SD-300 was valued at 709.2% higher final optimal yield than single-filter SS-300. As a result of analysis of optimal yield change over time, It was confirmed that the ratio of optimal yield of single filter and dual filter increase over time. In order to evaluate the long-term change in water intake efficiency, we considered the point at which the initial optimal yield was reduced by 50%. The dual filter SD-300 is about 351.1% higher than SS-300, which is the same thickness filter, and about 579.0% higher than SS-100. From these results, Assuming that the point at which the initial quantity of water intake is reduced to 50% is the well life, double filters are expected to increase their lifespan by about 3.5 times over single filters of the same thickness and by about 5.8 times over typical single filter. These results can be used to design wells to river bank filtration or filtered seawater. In addition, it is possible to clarify the effect of the double filter through the comparison with the future field test results.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.41 no.5
• /
• pp.551-557
• /
• 2021

Attached parking lots installation criteria is determined by use, total floor area, etc. according to the Parking Lot Act and local government ordinances. However, with traffic demand increase inconvenience about use of culture and assembly facilities have been raised. When planning number of parking lots for cultural and assembly facilities, legal parking lots and unit parking lots are used, but this causes inconvenience and traffic problems on the surrounding roads, because reality and convenience are not considered. Therefore, this study intend to present an realistic number of parking lots calculating equation for movie theater in Gwangju Metropolitan City. After investigating number of parking lots, number of screens, number of seats, total floor area, bus route and illegal parking for a cultural facility in Gwangju Metropolitan City, prediction model for calculating number of parking lots was presented using SPSS regression analysis. As a result of comparing prediction model and unit method, the prediction model was be closer actual cumulative parking space, so prediction model verification was completed. Based on the model verified in this study, Realistic number of parking lots will be installed. However, due to limitations of research on specific areas, research on various facilities should continue in consideration of regional, population, and urban characteristics

• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.716-716
• /
• 2012

최근 항만구조물을 설계함에 있어 대수심 및 고파랑 지역에 설치되는 외곽시설의 상당수는 직립식 케이슨 혼성제 단면을 채택하고 있다. 이는 상대적으로 수심이 깊고, 설계파와 같은 외력 조건이 크기 때문에 경사제에 비하여 경제성 및 시공성이 유리하기 때문으로 판단된다. 그렇지만 아직까지 소규모 항만 및 어항시설에 있어 경사제를 채택하고 있다. 본 연구에서는 이와 같은 경사식 구조물을 설계함에 있어 월파에 의한 방파제 배후 경사면에 피복된 피복재의 안정성을 검토하며, 실험사례를 통하여 최적 설계안 및 설계방향을 제시하고자 한다. 경사식 구조물 배후 사면 피복재의 안정 중량에 대해서는 우리나라의 항만 구조물의 설계기준(항만 및 어항설계기준, 2005) 뿐만 아니라 국외의 설계기준(CEM, Coastal engineering manual, 2005 등)에서도 아직까지 설계법을 제시하고 있지 않고 있다. 본 연구에서 수행한 단면 수리모형실험에서는 1/50의 실험축척을 적용하여 대상 외곽 구조물에 대하여 수리특성과 안정성을 검토하였다. 특히 경사제 배후의 안정성 확보를 위하려 동일 구간에 대하여 설계파 조건 등을 중심으로 총 9개의 실험안을 설정하여 안정성을 검토하였다. 아래 그림은 이중 초기 설계안과 최종적으로 제안된 제시안에 대한 완성모형, 실험장면 및 결과이다. 일반적으로 접안시설과 외곽시설이 어느 정도 이격되어 있어 적정량의 월파를 허용할 수 있는 경우 상치콘크리트의 형상 및 마루높이을 변경하여 월파의 낙하 및 도달거리를 배후면의 안정성을 확보할 수 있을 정도로 유도함으로써 안정적인 구조물 설계가 가능할 것으로 판단된다.

• Journal of Korean Medical classics
• /
• v.19 no.4
• /
• pp.27-61
• /
• 2006

수당오대적대근의학발전유소적정책(隨唐五代적代근의學발展有소的政策), 기구(기구), 제도등축점완비료(制度等逐漸完비了). 저시기유정부발전의학교육적정책치득의정적공적(저時期由政府발展의學교育的政策値得의政的功적). 정규의학교육적방면상몰치전과의(定規의學교育的方面上몰置전科의), 안배교육과정(安排교育과程), 임용고시등구비구비료의학교적규모(任用考시等具비具비了의學교的規模), 영외발전료지방의학교육화의학보급(영外발展了地方의學보育和의學普及). 방포의방화지방요로상다착처방적조시백성의료제공방변(방布의方和地方要路上다着처方的조百姓의료提供方便), 야영향료의학화신적보급(也影향了의學和신的普及). 저시기의정상최현저적성과시제고본초학적지위적(저時期의政上最현著的成果是提高本草學的地位的). 태의서내설치료의학교육동시설치료전문약학교육(太의署內設置了의學교育同時설置了전문葯學교育). 이차정부이편수본초학적병반포전국위최초적약전(而且政府以編수本草學籍幷반布全국위最初的葯典). 저시기유정부법제화료의약관리방면적야시대대수획(저時期由政府法制化了의葯管理方面的也是大大收획). 수당이전몰형성의약관리화유소제도(隨唐以前沒形成의葯管理和有소制度), 규모(規模). 의생근거일정적법률근환자관계병엄가구관자기(의生根据一定的法律근患者관系幷엄可拘管自己). 수당오대의정흔다방면상탁유성효(隨唐五代의政흔多方面上卓有成效), 단시궁정의약기구적규모흔방대(但是宮廷의葯기구的規模흔방大), 인원과잉(人員과剩), 역궁정의관수공제(亦宮廷의官受控制), 불능발휘자기적능력(不能발揮自己的能力). 야불능발전위백성적의약기구(也不能발展위百姓的의葯기구). 인위정부불태중시의학(因위政府不太重시의學), 소이의생적지위잉시불고(所以의生的地位仍是不高). 나취시저시기의정적결점(那就是저시期의政的缺点).

• Korean Journal of Agricultural Science
• /
• v.36 no.1
• /
• pp.73-85
• /
• 2009

An investigation was conducted to get the basic data for establishing structural safety and environmental management of tomato greenhouses in Chungnam region. The contents of the investigation consisted of actual state of greenhouse structures and environmental control facilities. Most of greenhouses were arch type single-span plastic houses and they had too low height for growing tomatoes. Frameworks of multi-span greenhouses were suitable, but those of single-span were mostly insufficient. Every greenhouse had thermal curtain movable or covering fixed inside the greenhouse for energy saving, and heating facilities were mostly warm air heater. Irrigation facilities were mostly drip tube and controlled by manual operation or timer. Almost all of the greenhouses didn't install high level of environmental control facilities such as ventilator, air circulation fan, $CO_2$ fertilizer, insect screen, supplemental light, and cooling device.

• Journal of Wetlands Research
• /
• v.22 no.2
• /
• pp.145-152
• /
• 2020

Highways are characterized by high non-point pollutant emissions due to high traffic volumes and sections that cause abrupt change in driving speed (i.e. rest stations, ticketing office, etc.). Most highways in Korea were constructed with layers that do not allow adequate infiltration. Moreover, non-point pollution reduction facilities were not commonly installed on domestic highways. This study was conducted to evaluate a facility treating highway runoff and develop a cost-effective design for infiltration facilities by using soil amendment techniques. Performing soil amendment increased the hydraulic retention time (HRT) and infiltration rate in the facility by approximately 30% and 20%, respectively. The facility's efficiency of removing non-point pollutants (Total Suspend Soiled (TSS), Chemical Oxygen Demand(COD), Biological Oxygen Demand(BOD), Total Nitrogen (TN) and Total Phosphorus, (TP) were also increased by 20%. Performing soil amendment on areas with low permeability can increase the infiltration rates by improving the storage volume capacity, HRT, and infiltration area. The application of infiltration facilities on areas with low permeability should comply with the guidelines presented in the Ministry of Environment's Standards for installation of non-point pollution reduction facilities. However, soil amendment may be necessary if the soil infiltration rate is less than 13 mm/hr.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.33 no.5
• /
• pp.427-436
• /
• 2015

This study aims to select an optimal site for the development of small-scaled artificial ground water recharge system with the purpose of 50ton/day pumping in dry season. First of all, the topography shape satisfying the numerous factors of a hydraulic model experiment is defined and an appropriate pumping efficiency is calculated through the model experiment of injection and pumping scenario. In next step, GIS(Geographic Information System) database are constructed by processing several geospatial data to explore the optimal site. In detail, watershed images are generated from DEM(Digital Elevation Model) with 5m cell size, which is set for the minimum area of the optimal site selection. Slope maps are made from DEM to determine the optimal hydraulic gradient to procure the proper aquifer undercurrent period. Finally, the suitable site for artificial recharge system is selected using an integration of overall data, such as an alluvial map, DEM, orthoimages, slope map, and watershed images.

• Tunnel and Underground Space
• /
• v.14 no.5
• /
• pp.373-380
• /
• 2004

In this study, the emission rate of pollutant was modified according to the published standards, and the distribution of pollutant concentration was analyzed for each vehicle velocity. This modified emission rate was applied to a model tunnel and it was proved that the required air quantity was reduced to 49%, compared to the PIARC method. From the simulation result, it was proved by using statistics that the most sensitive factor among them is the friction coefficient and it was modified to the value in the range of 0.018 to 0.021. It is also expected that the required air quantity can be decreased form 14.4% to 19.2% according as the coefficient is applied to the domestic model tunnels. In conclusion, it is proposed that the number of jet fans can be reduced and the annual operating cost can be curtailed as well.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.12 no.3
• /
• pp.63-75
• /
• 2004

This research sought to determine the status of the installation and operation of domestic public resource-making facilities of resource-making facilities and come up with corresponding improvement measures. Currently compost is most numerous set-up out of facilties already established ever since, then the rest of them are feeds, anaerobic degradation, sewage combination, and combination of compost and feeds in order. As such, food waste is processed more into compost than into feeds, presumably because relevant facilities, which were originally designed for processing into feeds, were converted into composting facilities due to little demand for the processed feeds. The finding says that many related firms had yet to register their businesses in accordance with feeds and fertilizers management laws, and that food waste resources-making facilities used various basic facilities but few of them treated food waste in linkage with leaching water, bad odors, and energy. Some of current facilities were found to be 7 years old and thus outdated. Due to lack of skilled operational manpower, many facilities had less than 300 days of normal operation yearly, and some needed minor and serious repairs periodically. In overall facilities, 87% of the planned food waste was rolled in, thus requiring measures to treat the whole planned volume. For costs of resource-making facilities, some with a capacity of below 50 tons topped 100 million won, and facilities with a capacity of over 50 tons required less installation costs. Overall, installation costs ranged from 10 million to 20 million, and to 200 million won per ton, and this suggests a need to establish the installation cost calculation criteria, as well as to reshape the facility criteria. With operating costs varying greatly according to the size and treatment methods of facilities, the finding indicates a need to rationalize the operating costs, and to plan appropriate-size installation and operation of facilities to ensure economic operation.

• The Journal of Engineering Geology
• /
• v.27 no.4
• /
• pp.405-416
• /
• 2017

This study evaluated a model unconfined aquifer comprising a sand or gravel layer, a filter layer, a pumping well, and an observation well. The model was employed in step drawdown tests and then used to assess the permeability of each test tank. The optimal yield and well efficiency were then calculated. Evaluation of yield by step in sand layer filters of equal thickness gave optimized watering rates of 22.03 L/min in the double filter and 19.71 L/min in the single filter. The double filter's yield was 115.0% that of the single filter. A comparison of double and single filters, each 10 cm thick, showed the double filter to have a maximum yield of 182.7%. Yields for the gravel layer were 73.56 L/min for a double filter and 65.47 L/min for a single filter of the same thickness; the former value is 112.3% of that of the latter. Comparison of double and single filters with 10-cm-thick gravel layers revealed that the double filter had a maximum yield of 160.9%. Results for sand wells showed the double filter to have a maximum efficiency of 70.4% and the single filter to have a minimum efficiency of 37.1%. Gravel-layer well efficiencies were >66.5% for both double and single filters (each 30 cm thick), but only 22.5% for a 10-cm-thick single filter. This study confirms that permeability improved as the filter material became thicker; it also shows that a double filter has a higher yield and well efficiency than a single filter. These results can be applied to the practical design of wells.