• Korean Journal of Materials Research
• /
• v.10 no.6
• /
• pp.450-455
• /
• 2000

For further scaling down of the silicon devices, the application of low dielectric constant materials instead of silicon oxide has been considered to reduce power consumption, crosstalk, and interconnection delay. In this paper, the effect of $O_2/SF_6$ plasma chemistry on the etching characteristics of polyimide-one of the promising low-k interlayer dielectrics-has been studied. The etch rate of polyimide decreases with the addition of $SF_6$ gas due to formation of nonvolatile fluorine compounds inhibiting reaction between oxygen and hydrocarbon polymer, while applying substrate bias enhances etching process through physical attack. However, addition of small amount of $SF_6$ is desirable for etching topography. $SiO_2$ hard mask for polyimide etching is effective under $O_2$plasma etching(selectivity~30), while $O_2/SF_6$ chemistry degrades etching selectivity down to 4. Based on the above results, $1-2\mu\textrm{m}$ L&S PI2610 patterns were successfully etched.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.8
• /
• pp.1-4
• /
• 2011

This study was the coorrelation between the electrical properties and the dielectric constant of organic inorganic hybrid type low k SiOC film. SiOC film as low-k films was deposited by the chemical vapor deposition and then annealed at 30 $0{\sim}500^{\circ}C$ to find out the properties of the depending on the temperature and polarity. SiOC film decreased the dielectric constant after annealing process, and the electrical properties were improved at the sample annealed at $400^{\circ}C$. From the XRD patterns, there were two kinds of bonding structures in SiOC film. There was the difference in the bonding structure between the samples annealed under $300^{\circ}C$ and the samples annealed over $400^{\circ}C$. The change was confirmed near $400^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.144-147
• /
• 2003

Cu+ ions drift diffusion in formal oxide film and SiOCH film for interlayer dielectric is evaluated. The diffusion is investigated by measuring shift in the flatband voltage of capacitance/voltage measurements on Cu gate capacitors after bias temperature stressing. At a field of 0.2MV/cm and temperature $200^{\circ}C,\;300^{\circ}C,\;400^{\circ}C,\;500^{\circ}C$ for 10min, 30min, 60min. The Cu+ ions drift rate of $SiOCH(k=2.85{\pm}0.03)$ film is considerable lower than termal oxide. As a result of the experiment, SiOCH film is higher than Thermal oxide film for Cu+ drift diffusion resistance. The important conclusion is that SiOCH film will solve a causing reliability problems aganist Cu+ drift diffuion in dielectric materials.

• Clean Technology
• /
• v.16 no.3
• /
• pp.191-197
• /
• 2010

Repair reaction of plasma damaged porous methyl doped SiOCH films was carried out with silylation agents dissolved in supercritical carbon dioxide ($scCO_2$) at various reaction time, pressure, and temperature. While a decrease in the characteristic bands at $3150{\sim}3560cm^{-1}$ was detectable, the difference of methyl peaks was not identified apparently in the FT-IR spectra. The surface hydrophobicity was rapidly recovered by the silylation. In order to induce effective repair in bulk phase, the wafer was heat treated before reaction under vacuum or ambient condition. The contact angle was slightly increased after the treatment and completely recovered after the subsequent silylation. Methyl groups were decreased after the plasma damage, but their recovery was not identified apparently from the FT-IR, spectroscopic ellipsometry, and secondary ion mass spectroscopy analyses. Furthermore, Ti evaporator was performed in a vacuum chamber to evaluate the pore sealing effect. The GDS analysis revealed that the open pores in the plasma damaged films were efficiently sealed with the silylation in $scCO_2$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.230-231
• /
• 2009

펄스 레이저 층착법 (이하 PLD)은 다성분계 산화물 박막 또는 다층구조의 박막 제작에 매우 유용한 기술이다. 본 실험에서는 KrF 엑시머 레이저를 이용하여 pt on Si 기판 위에 150nm 두께의 $Bi_{1.5}ZnNb_{1.5}O_7$(이하 BZN) 박막을 다양한 기판온도에서 제작하였다. XRD를 이용하여 BZN 박막의 구조적 특성을 분석하였고, 박막을 MIM 구조로 제작하여 유정적 특성을 측정하였다. 제조한 BZN 박막은 $500^{\circ}C$ 이상에서 결정질을, $500^{\circ}C$ 이하의 온도에서는 비정질 특성을 보였다. 유전 특성은 100 - 400$^{\circ}C$ 영역에서는 온도가 증가함에 따라 졸은 특성을 나타내었고, $500^{\circ}C$에서부터는 감소하였다. 증착 온도 $400^{\circ}C$에서 제작한 BZN 박막이 유전상수가 67.8, 유전 손실이 0.006으로 가장 줄은 유전특성을 나타내었다.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.10
• /
• pp.10-15
• /
• 1990

Theory and experimental results of measuring the microwave dielectric characteristics of low-loss materials by using dielectric rod resonator method are presented. The $TE_{011}$ mode resonance frequency was adapted to minimize the effect of the air gap between the rod and the conducting plates. The dielectric properties were computed from the resonance frequency, sample geometry and 3 dB bandwidth. The error of measurements was within ${\pm}3{\%}$ for dielectric constant and was within ${\pm}12{\%}$ for dielectric loss.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.11a
• /
• pp.477-480
• /
• 2002

Si-O-C(-H) thin film with a tow dielectric constant were deposited on a P-type Si(100) substrate by an inductively coupled plasma chemical vapor deposition (ICPCVD). Bis-trimethylsilymethane (BTMSM, H$_{9}$C$_3$-Si-CH$_2$-Si-C$_3$H$_{9}$) and oxygen gas were used as Precursor. Hybrid type Si-O-C(-H) thin films with organic material have been generated many voids after annealing. Consequently, the Si-O-C(-H) films can be made a low dielectric material by the effect of void. The surface characterization of Si-O-C(-H) thin films were performed by SEM(scanning electron microscope). The characteristic analysis of Si-O-C(-H) thin films were performed by X-ray photoelectron spectroscopy (XPS).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.148-148
• /
• 2009

반도체 소자의 크기가 45 nm 이하로 감소함에 따라 최소 선폭에 따른 다층 배선 연결 구조가 요구되고 있다. 그러나 고집적화 구조는 기생 저항과 정전 용량에 의한 신호지연증가 및 혼선 전력 소모의 문제가 발생한다. 이런 문제를 해결하기 위한 방법 중의 하나는 저저항 배선연결물질과 층간 절연막으로 저유전 상수를 갖는 물질을 사용하는 것이다. 본 연구는 DEMS $(H-Si(CH_3)(OC_2H_5)_2)$ 전구체를 이용하여 저유전막을 증착할 때 사용되는 PECVD (plasma enhanced chemical vapor deposition) 장비를 국내 기술로 개발하고 개발된 장비로 저유전박막을 평가한 것에 관한 것이다. 본 연구에서 평가 및 박막 종확 시 사용한 장비는 MAHA hp 1 type ((주)아토)로서 양산용 PECVD 장비이다. 변수는 C-He의 유랑, 300 mm Si 웨이퍼와 shower head 사이의 거리, 증착 압력, 구동 전력이고, 증착된 저유전막의 두께, 두께의 균일성, 굴절률, 굴절률의 균일성를 평가하였다. 구동 전력이 500W 일 때, C-He의 유량과 진공의 크기를 감소시키면 박막의 두께가 감소하고 박막의 균일성은 증가하였다. C-He의 유량을 증가시키고 shower head 와 Si 웨이퍼 사이의 거리 및 구동 압력을 감소시키면 굴절률과 굴절률의 균일성이 모두 저하되었다. 구동 전력이 700W 일 때, 박막 두께의 경우, 구동 전력이 500W 일 때의 결과와 유사하지만, 박막의 균일성, 굴절률, 굴절률의 균일성은 모든 조건에서 저하되었다.

• Applied Chemistry for Engineering
• /
• v.10 no.7
• /
• pp.1014-1019
• /
• 1999

Copolyamic acid PMDA/6FDA-PDA(PAA) and homopolyamic acids PMDA-PDA(PAA) and 6FDA-PDA(PAA) were synthesized from 1,2,4,5-benzenetetracarboxylic dianhydride(PMDA) and 2,2'-bis(3,4-dicarboxyphenyl) hexafluoropropane dianhydride(6FDA) as the dianhydride and 1,4-phenylenediamine (PDA) as the diamine. Residual stresses were detected in-situ during thermal imidization of the co- and homopolyimide precursors as a function of processing temperature over the range of $25{\sim}400^{\circ}C$ using thin film stress analyzer(TFSA), and morphological structures were investigated by WAXD. In comparison, the resultant residual stress of polyimide films composed of different compositions decreased with the increasing content of PMDA unit in the chain and was about 5 Mpa in compression mode for PMDA-PDA. In this study, the synthesis of random PMDA/6FDA-PDA copolyimide could be completed and compensate for the difficulty of process due to high $T_g$ of PMDA-PDA and relatively higher stress of 6FDA-PDA. It showed that we can make a low level stress copolyimied having excellent mechanical properties by incorporating appropriate rod-like rigid structure PMDA-PDA unit into 6FDA-PDA polyimide backbone which generally shows higher stress due to rotational hinges such as bulky di(trifluoromethyl). Specially, PMDA/6FDA-PDA(0.9:0.1:1.0) satisfied excellent mechanical property and low level stress as an inter layer showing low dielectric constant.

• Korean Journal of Materials Research
• /
• v.9 no.12
• /
• pp.1211-1215
• /
• 1999

Fluorinated amorphous carbon (a-C:F) films were prepared by an electron cyclotron resonance chemical vapor deposition (ECRCVD) system using a gas mixture of $C_2F_6$ and $CH_4$ over a range of deposition temperature (room temperature ~ 300$^{\circ}C$). 500$^{\AA}C$ thick DLC films were pre-deposited on Si substrate to improve the strength between substrate and a-C:F film. The chemical bonding structure, chemical composition, surface roughness and dielectric constant of a-C:F films deposited by varying the deposition temperature were studied with a variety of techniques, such as Fourier transform infrared spectroscopy(FTIR), X-ray photoelectron spectroscopy(XPS), atomic force microscopy (AFM) and capacitance-voltage(C-V) measurement. Both deposition rate and fluorine content decreased linearly with increasing deposition temperature. As the deposition temperature increased from room temperature to 300$^{\circ}C$, the fluorine concentration decreased from 53.9at.% down to 41.0at.%. The dielectric constant increased from 2.45 to 2.71 with increasing the deposition temperature from room temperature to 300$^{\circ}C$. The film shrinkage was reduced with increasing deposition temperature. This results ascribed by the increased crosslinking in the films at the higher deposition temperature.