• The KSFM Journal of Fluid Machinery
• /
• v.11 no.6
• /
• pp.54-63
• /
• 2008

A study on the flow characteristics in a 4-stage axial compressor and the behavior of rotating stall was experimentally performed at the third-stage rotor and stator rows in order to investigate its performance and instability of the compression system. The pressure losses generated due to the leakage flow at a tip clearance and a shroud seal clearance and the wake flow near the trailing edge of a blade were taken into consideration to estimate the causes of performance drop of the low speed research compressor(LSRC) in Seoul national university. In addition, the measurement of rotating stall was conducted with hot-wire probes and the existence and propagation of stall cell could be confirmed through fast Fourier transform and cross-correlation analysis.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.6
• /
• pp.788-802
• /
• 1998

A numerical method using dual time stepping and preconditioning procedure for efficient computations of unsteady low speed compressible flow problems is developed. The time-derivative preconditioning method which is valid at low speed flow conditions cannot maintain temporal accuracy because of the modification of the time-derivative term in Navier-Stokes equations. The dual time stepping procedure is incorporated to enable the time accurate computations and this procedure introduces a pseudo-time derivative in addition to the physical time derivative. At a given physical time, an inner iteration can be carried out until a steady state in pseudo-time is achieved. This will effectively yield a time accurate solution. Computational capabilities of the above algorithm are demonstrated through computation of a variety of practical fluid flows and it is shown that the algorithms is efficient in the essentially incompressible flows and low Mach number compressible flows with heat source.

• Journal of Energy Engineering
• /
• v.9 no.2
• /
• pp.146-155
• /
• 2000

연료분출을 수반하는 원통형 보염기 후류에 형성되는 확산화염에 대한 이온전류의 특성과 화염의 안정범위를 측정, 분석함으로써 연소특성을 고찰하였다. 난류강도가 큰 경우의 화염일수록 화염의 안정성은 악화되며, 화염내 중앙의 평균 이온전류값이 가장 높은 값을 갖는 영역은 블로오프 직전상태에 비해서 안정시의 경우 더욱 하류측에 존재한다. 난류의 정도가 강한 화염의 경우 국소적으로 반응이 활발한 화염 덩어리가 빠른 속도로 이동하며, 난류의 정도가 강한 화염의 경우에는 반응이 완만한 화염 덩어리가 저속으로 이동한다. 재순환영역에서 주류유동측으로 이동함에 따라 자기상관계수의 저하가 빨라지고 난류 시간스케일이 작아지며, 부염기 직후에서 하류로 이동함에 따라 자기상관계수의 저하가 늦어지고 난류시간스케일이 커진다. 주류공기에 강한 난류를 가하지 않은 경우에는 큰 난류시간스케일에 대응되는 저주파수 특성이외에도 작은 난류 시간스케일에 대응되는 고주파수 특성이 나타나며 , 주류공기에 강한 난류를 가한 경우에는 큰 난류 시간스케일에 대응되는 저주파수 특성이 나타난다.

• Journal of KSNVE
• /
• v.8 no.5
• /
• pp.914-921
• /
• 1998

Combusion instability due to thermoacoustic feedback in a ducted combustor usually excites severe noise and vibration, which could lead to result in the failure of the system or environmental dispute. In the present study, an active noise control(ANC) method with an adaptive algotithm is hired to suppress instability which has very discrete behavior in the frequency domain. Especially a feedback system is composed to evade hot environment of the combustor, and as a preliminary, the performance and stability of the controller is chekced by simulating the real situation with harmonic waves. Application to the real combustor showed serious reductions in sound pressure level by 20∼30 dB. It was also shown that the selected control system was very stable and effective.

• Journal of Industrial Technology
• /
• v.15
• /
• pp.153-168
• /
• 1995

The purpose of this study is to develop a method for predicting the aerodynamic performance of the subsonic airfoils in the 2-dimensional, steady and viscous flow. For this study, the airfoil geometry is specified by adopting the longest chord line system and by considering local surface curvature. In case of the inviscid-incompressible flow, the analysis is accomplished by the linearly varying strength vortex panel method and the Karman-Tsien correction law is applied for the inviscid-compressible flow analysis. The Goradia's integral method and the Truckenbrodt integral method are adopted for the boundary layer analysis of the laminar flow and the turbulent flow respectively. Viscous and inviscid solutions are converged by the Lockheed iterative calculating method using the equivalent airfoil geometry. And the analysis of the seperated flow is performed using the Dvorak and Maskew's method as the basic method. The wake effect is also considered and its geometry expressed by the formula of Summey & Smith when no seperation occurs. A computational efficiency is verified by the comparison of the computational results with experimental data and by the shorter execution time.

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.135-140
• /
• 2011

The battery pack, a main component of NEV(Neighborhood Electric Vehicle), needs cooling system when it is charging or discharging to prevent the degradation of the battery charging efficiency. The purpose of this study is to analyse the effects of cooling methods, changing positions of inlet and outlet and changing area ratios of inlet and outlet. It has been observed that in the point of uniform cooling suction from the exit side is more efficient than blowing from the inlet. And there is a suitable inlet/outlet area ratio in maximizing the mass flow rate. The numerical analyse using a commercial code STAR-CCM+ version 4.02 were used for the study.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.688-693
• /
• 2003

The PSP technique has been used to measure pressure distribution on a model surface quantitatively. The objective of this study is to develop PSP technique which can be applied to low-speed flows. Four different PSP formulations including two porphyrins (PtOEP and PtTFPP) and two polymers (Poly(TMSP) and RTV-118) were tested and the performance of each combination was checked. In the static calibration, the luminescent intensity of the PSP coatings was measured from 0kPa to 11kPa with 0.5, 1, 2kPa increments. Among 4 PSP formulations tested, the combination of PtOEP and RTV-118 shows the best performance. The PSP technique was applied to an oblique impinging jet to measure the pressure field distribution on the impinging plate.

• Computational Structural Engineering
• /
• v.11 no.4
• /
• pp.147-154
• /
• 1998

강체 충격자가 납 표적에 33m/s ∼ 141m/s의 속도로 충돌할 때의 침투특성을 연구하기 위하여 Jognson 이론식을 이용한 이론해석과 AUTODYN 코드를 이용한 수치해석 및 실험장치를 이용한 실험측정을 실시하고 그 결과들을 비교 분석하였다. 실험장치로는 가스압력식 발사장치를 설계 제작하였으며, 실험용 충격자로는 충돌부위 형상이 반구형인 반구형 충격자와 원추형인 원추형 충격자 2종류를 사용하였다. 또한, 납재료에 대한 동적 유동응력을 얻기 위하여 홉킨스 압력봉실험을 수행하였다. 침투특성에 관한 연구결과, 이론적 해석결과는 저속 충돌범위(반구형 충격자 : 53m/s, 원추형 충격자 ; 73m/s)에서 실험결과치와 93%이상 잘 일치하였으며, 수치해석결과는 전체적인 충돌속도 범위에서 반구형 충격자인 경우 73%이상, 원추형 충격자인 경우 86%이상 일치하였다.

• Journal of computational fluids engineering
• /
• v.16 no.3
• /
• pp.82-87
• /
• 2011

The battery pack, a main component of NEV(Neighborhood Electric Vehicle), needs cooling system when it is charging or discharging to prevent the degradation of the battery charging efficiency. The purpose of this study is to analyse the effects of cooling methods, changing positions of inlet and outlet and changing area ratios of inlet and outlet. It has been observed that in the point of uniform cooling, suction from the exit side is more efficient than blowing from the inlet. And there is a suitable inlet/outlet area ratio in maximizing the mass flow rate. A commercial code, STAR-CCM+(ver. 4.02), was used for the numerical study.

• Solar Energy
• /
• v.15 no.1
• /
• pp.39-51
• /
• 1995

A numerical scheme based on a coordinate transform into stream function-velocity potential is proposed to solve heat and momentum transfer in porous media with phase change. A significant simplification of both computational domain and governing equations can be achieved by the transform. The dispersion term in the flow through porous media, which is important at the phase change interface, can be successfully incorporated into the numerical scheme without introducing any further computational complications.