• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.11
• /
• pp.611-617
• /
• 2016

Remanufacturing that is the rebuilding of a product to specifications of the original manufactured product by collecting used-product, completely disassembling, cleaning and repairing or replacing with a new part and reassembling has been received attention in aspects of resource, recycling because it is a great environmental improvement. Remanufacturing is the rebuilding of a product to specifications of the original manufactured product by collecting used-product, completely disassembling, cleaning and repairing or replacing with a new part and reassembling. With a great environmental improvement and resource recycling and conservation, many studies were conducted. Up to date, remanufacturing activities are mainly applied to automobile parts and printer toner cartridge in South Korea. However, remanufacturing of rental product is not well conducted although rental products are collected in good condition and could be remanufactured in the same condition as a new product. Therefore, in this study, we conducted life cycle assessment (LCA) to an air cleaner product that is one of rental products. This study attempts to identify the processes in new products and remanufacturing life cycles that contribute the most environmental impacts. The results show that air cleaner remanufacturing could reduce about 20% of environmental impacts compared to new product. The greatest benefit related to environmental impact is with regard to ozone layer depletion potential (ODP), which is reduced by 94%. In the life cycle of air cleaner, raw material extraction stage had the most environmental impacts, especially with regard to abiotic depletion potential (ADP) and global warming potential (GWP). In the environmental impacts in each part, the ABS power had the highest environmental impacts.

• Economic and Environmental Geology
• /
• v.40 no.2 s.183
• /
• pp.209-221
• /
• 2007

Numerical analysis was performed to investigate the effect of heavy metal contamination on neighboring environment in case a dam is constructed by using rockfill materials contaminated by heavy metals. The numerical simulation carried out in this research includes both subsurface flow and contaminant transport in the inside of the CFRD(Concrete Faced Rockfill Dam), using two commercial programs, SEEP2D and FEMWATER. The three representative cases of scenarios were chosen to consider a variety of cases occurring in a dam site; (1) Scenario 1 : no crack in the concrete face slab, (2) Scenario 2 : a crack In the upper part of face slab, and (3) Scenario 3 : a crack between plinth and face slab in the lower part of face slab. As a result of seepage analysis, the amount of seepage in scenario 2 was calculated as $14.31\sim14.924m^3/day$ per unit width, corresponding to the 1,000 times higher value than that in other scenarios. Also, in the simulation of contaminant transport by using FEMWATER, specified contaminant concentration of 13 ppb in main rockfill zone was set to consider continuous leakage from the rock materials. Through the analysis of contaminant transport, we found that elapsed times to take for the contaminant concentration of about 2 ppb to arrive at the end of a dam are as follows. Scenario 1 has the elapsed time of 55,000 years. In Scenario 2. it is 50 years. Finally, scenario 3 has 27,000 years. The rapid transport of the contaminant in scenario 2 was attributed to greater seepage flow by 500 times than other scenarios. Although, in case of upper crack in the face slab, it was identified that the contaminant might transport to the end of a dam within 100 years with about 2 ppb concentration, however, it happened that the contaminant was hardly transported out of the dam in other scenarios, which correspond to either no crack or a crack between plinth and face slab. In conclusion, the numerical analysis showed that the alternative usage of the contaminated sand and gravel as the dam embankment material can be one of the feasible methods with the assumption that the cracks in a face slab could be controlled adequately.

• Journal of Chest Surgery
• /
• v.31 no.7
• /
• pp.674-678
• /
• 1998

The conventional surgical treatment of isolated critical stenosis of the left main coronary artery restores a less physiologic perfusion of the myocardium, leads to occlusion of the left coronary ostium, and consumes an appreciable length of bypass material. From June 1994 to February 1996, eleven patients, three male and eight female, underwent patch angioplasty and additional bypass graft to left anterior descending artery (10 internal mammary artery, 1 saphenous vein) in isolated critical left main coronary artery stenosis. Their ages ranged from 34 to 62 years, mean 44 years. All had 60% to 90% stenosis of the left main coronary artery and Class III angina. The angiogram showed nine osteal lesion and three main stem stenosis. The operation was performed with conventional cardiopulmonary bypass and cold blood cardioplegia. We approached anteriorly and used bovine pericardium as onlay patch in all patients. There were one leg wound dehiscence, but no operative deaths and infarctions. All patients are free of symptoms after a mean follow-up of 15.5 months. Angiographic restudy at an average 14.4 months was obtained in five patients and showed widely patent left main coronary artery with excellent runoff. But additional graft to left anterior descending coronary artery were stenosed in two patients and showed diminutive flow in others. Our preliminary results suggest that angioplasty of the left main coronary artery can be carried out with low operative risks. But additional bypass graft to left anterior descending coronary artery may be unnecessary. The technique appears to be a promising alternative to conventional coronary artery bypass grafting in isolated left main coronary artery stenosis.

• Korean Journal of Heritage: History & Science
• /
• v.54 no.2
• /
• pp.78-97
• /
• 2021

Seojangdaeyajodo is a drawing of military night training on February 12th (lunar leap month), 1795. Focusing on the Seojangdaeyajodo, the characteristics and of the costumes worn by various types of officials were examined. There were 34 officials located near King Jeongjo in and around Seojangdae, with 27 Dangsanggwan and 7 Danghagwan. They wore three types of costumes, including armor, yungbok, and military uniforms. All of the twelve armor wearers and the five officials wearing yungbok were dangsanggwan, and the military uniform wearers included eleven dangsanggwan and six danghagwan. For the shape of the armor, the armor relics of General Yeoban, suitable for riding horses, and the armor painting of Muyedobotongji were referenced, and the composition of the armor was based on practicality. The armor consists of a helmet, a suit of armor, a neck guard, armpit guards, arm guards, and a crotch guard. The color of the armor was red and green, which are the most frequently used colors in Seojangdaeyajodo. The composition of yungbok was jurip, navy cheollik, red gwangdahoe, socks made of leather, and suhwaja. The composition of the military uniform was a lined jeolrip, dongdari, jeonbok, yodae, jeondae, and suhwaja. There were differences in the fabrics used in dangsanggwan and danghagwan military uniforms. Dangsanggwan used fabric with depictions of clouds and jewels, and danghagwan used unpatterned fabric. Moreover, jade, gold, and silver were used for detailed ornamental materials in dangsanggwan. The weapons included bows and a bow case, a sword, a rattan stick, wrist straps, and a ggakji. In the records of the King Jeongjo period, various colored heopsu were mentioned; the colors of the dongdari and jeonbok of dangsanggwan and danghagwan were referenced in various colors. It was presented as an illustration of costumes that could be used to produce objects accurately reflecting the above historical results. The basic principle of the illustration was to present the modeling standards for 3D content production. Samples of form, color, and material of the corresponding times and statuses were presented. The front, the side, and the back of each costume and its accessories were presented, and the colors were presented in RGB and CMYK.

• Journal of the Korea Institute of Building Construction
• /
• v.24 no.2
• /
• pp.181-191
• /
• 2024

In the realm of cement manufacturing, concerted efforts are underway to mitigate the emission of greenhouse gases. A significant portion, approximately 60%, of these emissions during the cement clinker sintering process is attributed to the decarbonation of limestone, which serves as a fundamental ingredient in cement production. Prompted by these environmental concerns, there is an active pursuit of alternative technologies and admixtures for cement that can substitute for limestone. Concurrently, initiatives are being explored to harness technology within the cement industry for the capture of carbon dioxide from industrial emissions, facilitating its conversion into carbonate minerals via chemical processes. Parallel to these technological advances, economic growth has precipitated a surge in construction activities, culminating in a steady escalation of construction waste, notably waste concrete. This study is anchored in the innovative production of calcium silicate cement clinkers, utilizing finely powdered waste concrete, followed by a thorough analysis of their mineral phases. Through X-ray diffraction(XRD) analysis, it was observed that increasing the substitution level of waste concrete powder and the molar ratio of SiO₂ to (CaO+SiO₂) leads to a decrease in Belite and γ-Belite, whereas minerals associated with carbonation, such as wollastonite and rankinite, exhibited an upsurge. Furthermore, the formation of gehlenite in cement clinkers, especially at higher substitution levels of waste concrete powder and the aforementioned molar ratio, is attributed to a synthetic reaction with Al₂O₃ present in the waste concrete powder. Analysis of free-CaO content revealed a decrement with increasing substitution rate of waste concrete powder and the molar ratio of SiO₂/(CaO+SiO₂). The outcomes of this study substantiate the viability of fabricating calcium silicate cement clinkers employing waste concrete powder.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.11 s.353
• /
• pp.37-47
• /
• 2006

This work proposes a 10b 25MS/s $0.8mm^2$ 4.8mW 0.13um CMOS A/D Converter (ADC) for high-performance wireless communication systems such as DVB, DAB and DMB simultaneously requiring low voltage, low power, and small area. A two-stage pipeline architecture minimizes the overall chip area and power dissipation of the proposed ADC at the target resolution and sampling rate while switched-bias power reduction techniques reduce the power consumption of analog amplifiers. A low-power sample-and-hold amplifier maintains 10b resolution for input frequencies up to 60MHz based on a single-stage amplifier and nominal CMOS sampling switches using low threshold-voltage transistors. A signal insensitive 3-D fully symmetric layout reduces the capacitor and device mismatch of a multiplying D/A converter while low-noise reference currents and voltages are implemented on chip with optional off-chip voltage references. The employed down-sampling clock signal selects the sampling rate of 25MS/s or 10MS/s with a reduced power depending on applications. The prototype ADC in a 0.13um 1P8M CMOS technology demonstrates the measured DNL and INL within 0.42LSB and 0.91LSB and shows a maximum SNDR and SFDR of 56dB and 65dB at all sampling frequencies up to 2SMS/s, respectively. The ADC with an active die area if $0.8mm^2$ consumes 4.8mW at 25MS/s and 2.4mW at 10MS/s at a 1.2V supply.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.29 no.3
• /
• pp.153-161
• /
• 2023

The worldwide effects of COVID-19 have led to a surge in online shopping and contactless services. The consumption pattern has caused the issues such as the environmental pollution together with the increase of plastic waste. Reducing the reliance on the petroleum based plastic use for the package and replacing it with environmentally friendly material are the simple ways in order to solve those problems. Paper is an eco-friendly product with high recyclability as the food packaging materials but has still poor barrier properties. A barrier coating on surface of the paper can be achieved with the proper packaging materials featuring water, gas and grease barrier. Polyethylene (PE) or polypropylene (PP) coatings which are generally laminated or coated to paper are widely used in food packaging applications to protect products from moisture and provide water or grease resistance. However, recycling of packaging containing PE or PP matrix is limited and costly because those films are difficult to degrade in the environment. This study investigated the recyclability of modified acrylic emulsion coating papers compared to PE and PP polymer matrixes as well as their mechanical and gas barrier properties. The results showed that PE or modified acrylic emulsion coated papers had better mechanical properties compared to the uncoated paper as a control. PE or PP coating papers showed strong oil resistance property, achieving a kit rating of 12. Those papers also had a significantly higher percentage of screen reject during the recycling process than modified acrylic coated paper which had a screen rejection rate of 6.25%. In addition an uncoated paper had similar value of a screen rejection rate. It may suggest that modified acrylic emulsion coating paper can be more easily recycled than PE or PP coating papers. The overall results of the study found that modified acrylic emulsion coating paper would be a viable alternative to suggest a possible solution to an environmental problem as well as enhancing the weak mechanical and poor gas barrier properties of the paper against moisture.

• Journal of Cadastre & Land InformatiX
• /
• v.54 no.1
• /
• pp.63-74
• /
• 2024

The fundamental basis for revitalizing cultural resources and developing content is national heritage(cultural property). In national heritage, cultural heritage is a tangible cultural heritage that represents the uniqueness of history and tradition, identity, and changes in life. In the case of museums, the collections (a museum-owned cultural heritage) represent the unique characteristics of the institution. In South Korea, it is recommended that museum collections be registered and used in the Cultural Heritage Standard Management System so that cultural heritage can be managed and utilized in connection with academics, industry, and administration. However, due to a lack of awareness of modern and contemporary heritage, the thematic classification chronology of the system was set mainly before the Joseon Dynasty, and a cultural heritage classification system suitable for national land information has not been established. Therefore, this study aims to propose a classification system for cadastral cultural heritage, based on the modern era when cadastral terminology was first used, using the cultural heritage owned by the LX Museum. Cadastral cultural heritage is characterized by the fact that although it is a field of specialized technology, the surveying or the production of it is not done by specific individuals only, and that while the production is professional, there are many educational aspects in its use. Therefore, unlike other specialized museum collections that are classified based on the functional aspects of their production methods, intended use, and creators, the classification method for cadastral cultural artifacts should be based on the characteristics of the cadastral tools and the outputs. This classification follows a three-tier stages with reference to the items in the Cultural Heritage Standard Management System. This classification aims at the effective use of knowledge by categorizing concepts and systematizing the subjects of data into a series of orders. A safe conservation and management environment for cadastral cultural heritage can be established, and academic and socio-cultural interpretation of the collection is possible by this classfication. Moreover, It is also expected to serve the basis for the national land information as well as searching for the national land information research, planning a exhibition, and the field of education in museum.

• The Journal of Korean Society for Radiation Therapy
• /
• v.23 no.1
• /
• pp.31-39
• /
• 2011

Purpose: Helical Tomotherapy allows only coplanar beam delivery because it does not allow couch rotation. We investigated a method to introduce non-coplanar beam by tilting a patient's head for Tomotherapy. The aim of this study was to compare intrafractional movement during Tomotherapy between coplanar and non-coplanar patient's setup. Materials and Methods: Helical Tomotherapy was used for treating eight patients with intracranial tumor. The subjects were divided into three groups: one group (coplanar) of 2 patients who lay on S-plate with supine position and wore thermoplastic mask for immobilizing the head, second group (non-coplanar) of 3 patients who lay on S-plate with supine position and whose head was tilted with Variable Axis Baseplate and wore thermoplastic mask, and third group (non-coplanar plus mouthpiece) of 3 patients whose head was tilted and wore a mouthpiece immobilization device and thermoplastic mask. The patients were treated with Tomotherapy after treatment planning with Tomotherapy Planning System. Megavoltage computed tomography (MVCT) was performed before and after treatment, and the intrafractional error was measured with lateral(X), longitudinal(Y), vertical(Z) direction movements and vector ($\sqrt{x^2+y^2+z^2}$) value for assessing overall movement. Results: Intrafractional error was compared among three groups by taking the error of MVCT taken after the treatment. As the correction values (X, Y, Z) between MVCT image taken after treatment and CT-simulation image are close to zero, the patient movement is small. When the mean values of movement of each direction for non-coplanar setup were compared with coplanar setup group, X-axis movement was decreased by 13%, but Y-axis and Z-axis movement were increased by 109% and 88%, respectively. Movements of Y-axis and Z-axis with non-coplanar setup were relatively greater than that of X-axis since a tilted head tended to slip down. The mean of X-axis movement of the group who used a mouthpiece was greater by 9.4% than the group who did not use, but the mean of Y-axis movement was lower by at least 64%, and the mean of Z-axis was lower by at least 67%, and the mean of Z-axis was lower by at least 67%, and the vector was lower by at least 59% with the use of a mouthpiece. Among these 8 patients, one patient whose tumor was located on left frontal lobe and left basal ganglia received reduced radiation dose of 38% in right eye, 23% in left eye, 30% in optic chiasm, 27% in brain stem, and 8% in normal brain with non-coplanar method. Conclusion: Tomotherapy only allows coplanar delivery of IMRT treatment. To complement this shortcoming, Tomotherapy can be used with non-coplanar method by artificially tilting the patient's head and using an oral immobilization instrument to minimize the movement of patient, when intracranial tumor locates near critical organs or has to be treated with high dose radiation.

• Development and Reproduction
• /
• v.6 no.2
• /
• pp.111-115
• /
• 2002

5-Hydroxytryptamine(5-HT; serotonin) system has been implicated in the modulation of male sexual behaviors and the secretion of reproductive hormones. In human males, selective serotonin re-uptake inhibitors(SSRIs) are known to improve the major male sexual dysfunction, premature ejaculation, through the central nervous system-mediated pathways. As numerous hormone and local factors, 5-HT may have peripheral role in the regulation of male sexual function. The expression of 5-HT receptor subtypes in the target tissue, however, has not been explored yet. The present study was undertaken to test whether the 5-HT receptor subtypes are expressed in the reproductive tissues of male rat, especially in ejaculatory machinery such as seminal vesicle and vas deferens. To do this, reverse transcription-polymerase chain reaction(RT-PCR) and Southern blot analysis were employed. The transcripts for the 1A, 1B and 2C subtypes of 5-HT receptor were amplified in all the tested tissues. The present study demonstrated the expression of 5-HT receptor in the rat ejaculatory machinery, suggesting that 5-HT may play a pivotal role in the male sexual function via not only central pathway but also peripheral route. Further study on the receptor subtype-specific effect and their harmonized mode of action will be needed to establish the understanding of ejaculation mechanism and drug design.