• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2001.04a
• /
• pp.34-34
• /
• 2001

열CVD법에 의하여 아세틸렌 가스를 탄소 원으로 사용한 탄소 나노튜브의 성장거동을 조사하였다. 닉켈 분말의 직경을 15nm 내지 90nm 범위로 조정하여 기판 에 촉매로 배열하였다. 탄소 나노튜브는 질소, 수소, 알곤, 암모니아 등 여러가지의 가스 분위기에서 증착되었으며 이들 가스의 혼합 분위기가 탄소나 노튜브의 성장에 미치는 영향을 조사하였다. 증착은 대기압 압력하에서 85$0^{\circ}C$ 의 온도에서 이루어졌다. 순수한 질소 분위기에서는 탄소 나노튜브의 성장이 이루어지지 않고 두꺼운 탄소 층이 기판 위에 중착되었다. 이 조건에서는 탄소로 뒤덮혀진 닉켈 입자가 탄소 나노튜브 형성의 촉매 역할을 담당하지 못했다. 그러나 질소와 수소의 혼합분위기에서는 수소의 농도가 증가함에 따라 탄소 나노튜브의 성장이 증진되었다. 순수한 수소 분위기에서는 일정한 방향이 없이 꼬여진 탄소 나노튜브가 성장되었다. 탄소 나노튜브의 성장은 분위기 가스로 암모니아를 사용하였을 때 훨씬 더 증진되었다. 수직으로 배열된 탄소 나노튜료를 암모니아 분위기에서는 성장시킬 수 있었으나 암모니아와 같은 비율의 수소와 질소 가스의 혼합 분위기 하에서 는 탄소 나노튜브의 성장을 얻을 수 없었다. 이러한 결과를 여기에서는 닉켈 촉매의 표면에 과도하게 석출된 탄소의 촉매 passivation으로 설명하였다. 탄소 나노튜브의 증착을 위해서는 아세틸렌 가스의 분해율이 너무 과도하지 않게 즉 촉매의 표면이 과도한 탄소의 증착으로 수동태화 되지않도록 조절되어야 한다는 것이다. 이 연구결과는 분위기 가스의 조성이 탄소 나노튜브의 성장에 있어서 그 반웅 kinetics에 큰 영향을 미친다는 것을 잘 보여주고 있다. 또한 암모니아 분위기에서는 촉매 닉켈입자 표면에 질화물층이 형성되어 탄소 나노튜브의 성장에 영향을 미쳤다는 것도 알 수 있었다.며 실제 가공업체에서도 터짐 문제가 발견되지 않았다. 결론적으로 표면층의 인장강도가 패션/구부림에 가장 중요한 변수로 작용하며 어떠 한 형태로 표면층의 인장강도를 향상시킬 경우 침엽수 펄프는 재생펄프로 대체가 가능 할 것으로 판단된다.하는 통계기법 중의 하나인 주성분회귀분석을 실시하였다. 주성분 분석은 여러 개의 반응변수에 대하여 얻어진 다변량 자료의 다차원적인 변 수들을 축소, 요약하는 차원의 단순화와 더불어 서로 상관되어있는 반응변수들 상호간 의 복잡한 구조를 분석하는 기법이다. 본 발표에서는 공정 자료를 활용하여 인공신경망 과 주성분분석을 통해 공정 트러블의 발생에 영향 하는 인자들을 보다 현실적으로 추 정하고, 그 대책을 모색함으로써 이를 최소화할 수 있는 방안을 소개하고자 한다.금 빛 용사 둥과 같은 표면처리를 할 경우임의 소재 표면에 도금 및 용 사에 용이한 재료를 오버레이용접시킨 후 표면처리를 함으로써 보다 고품질의 표면층을 얻기위한 시도가 이루어지고 있다. 따라서 국내, 외의 오버레이 용접기술의 적용현황 및 대표적인 적용사례, 오버레이 용접기술 및 용접재료의 개발현황 둥을 중심으로 살펴봄으로서 아직 국내에서는 널리 알려지지 않은 본 기 술의 활용을 넓이고자 한다. within minimum time from beginning of the shutdown.및 12.36%, $101{\sim}200$일의 경우 12.78% 및 12.44%, 201일 이상의 경우 13.17% 및 11.30%로 201일 이상의 유기의 경우에만 대조구와 삭제 구간에 유의적인(p<0.05) 차이를 나타내었다.는 담수(淡水)에서 10%o의 해수(海水)로 이주된지 14일(日) 이후에 신장(腎臟)에서 수축된 것으로 나타났다. 30%o의 해수(海水)에 적응(適應)된 틸라피아의 평균 신사구체(腎絲球體)의 면적은 담수(淡水)에

• Journal of Conservation Science
• /
• v.36 no.3
• /
• pp.197-212
• /
• 2020

This study analyzed the microstructure of ring-pommel swords, excavated from Ancient Tombs, Hadae, Ulsan and examined their production technique, using non-destructive testing and a metallurgical method. The results confirmed that the five ring-pommel swords, unearthed in Ancient Tombs, Hadae, Ulsan, as identified by radiographic non-destructive testing, had been solely manufactured using iron, through forging based on the single-piece technique. Furthermore, these results were compared with previous studies, and the manufacturing techniques of single-piece ring-pommel swords were categorized into three types: pure iron - changing the shape, pure iron - changing the shape - carburization, and steel - changing the shape - quenching. The ring-pommels of four swords had around 0.7% of carbon content, which is as much as for eutectoid steel and higher than for other parts of these swords, such as the backs of their blades and handles. The weapon function of a small ring-pommel sword, under 60cm in length, was maximized by quenching focusing on its blade. Conversely, the martensite quenching structure was not observed in four ring-pommel swords shorter than 75cm. In other words, the same types of single-piece ring-pommel swords(late in 2C~early in 4C) were unearthed from Ancient Tombs, Hadae, and the group who has manufactured these swords is presumed to have limited their effectiveness, functionally depending on purposes, through an iron-making process and heat-treatment techniques.

• Journal of Conservation Science
• /
• v.31 no.4
• /
• pp.499-506
• /
• 2015

The artifacts of Admiral Yi Sun-sin (Treasure No.326) consist of six items with two long swords, a jade decoration, a belt and two peach-shaped cups. In commemoration of the opening of Chungmugong Yi sun-sin Memorial Museum (April 28, 2011), there were conservation treatments for those artifacts at the beginning of 2011. At that time, from the result of non-destructive surface analysis on pigments in blood-colored grooves of the two long swords, it was presumed to be synthetic resin paints. This study shows the accurate identification on pigments which was presumed as synthetic resin paints and its removal. To identify pigments in blood-colored grooves, the optical microscope, scanning electron microscope, Micro-XRF, XRD and FT-IR were used for the analysis. The results turned out that the thickness of $10{\sim}90{\mu}m$ in a single layer was measured. And major components containing Pb and Cr and lead chromium molybdenum oxide were identified and to identify components of adhesives from the analysis by FT-IR, it turned out to be alkyd resin, which can be presumed that they were recently colored with synthetic paints. The synthetic paints easily react with most of the organic solvents. And it is so easy to handle without the effect on metal that it was removed with acetone. While removing synthetic paints, all of paints on it were collected for identifying whether there is traditional pigment but nothing was identified.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.8 no.1
• /
• pp.23-39
• /
• 2005

As developing satellite communication, the tracking range of the moving objects which move in local area is expanded to the whole world. However previous logistics management system is able to monitor freight which transporting in local area using mobile communication system. In this paper, we propose the reefer container management system that manages the location information and other related information such as temperature, humidity of container using the satellite system. The proposed system consists of three parts; data collector, satellite communication manager, reefer container information manager. And the proposed system uses the moving object index for managing the trajectory of container and tracing the location of container or vessel that is transporting the container, and supports various services such as reefer container and vessel tracking, container control and container statistics to logistic companies like shipper and forwarding agent. And the system can be increasing the quality of container transportation service to the shipper, and it makes the efficient management of reefer container to the shipping company.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.19 no.1
• /
• pp.180-196
• /
• 2016

To minimize the damage from disasters, various aspects of prevention, preparation, and response, etc. are being managed. Even though prevention and preparation are well conducted, irresistible calamities such as natural disasters may cause unexpected damage. Therefore, a system that can share the identical disaster information based on prompt disaster management and prediction must be developed and constructed for integrated disaster management. Especially, for a prompt disaster response, the same information needs to be shared between the related organization and the disaster prevention personnel such as on-site officials. Recent disaster management systems use high-capacity geographic information or other various factors for accurate disaster predictions. In case of using a recently constructed or researched 3D GIS, the system may not be used in some cases due to conflicts with hardware, etc. Thus, even though response information is secured using prediction simulation in advance, it is essentially difficult in some cases to share the common information when the system cannot be utilized or the extension of the corresponding data cannot be read. Therefore, this study aims to construct a system for dealing with disasters that shares the same prompt and accurate information in compliance with common data formats. The system is expected to reduce the existing disaster response time and minimize human and physical damage by assisting decision making through prompt responses.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.8 no.4
• /
• pp.53-64
• /
• 2009

Inter-vehicular communication that propagates information without infrastructures has drawn a lot of interest. However, it is difficult to apply conventional ad-hoc routing protocols directly in inter-vehicular communication due to frequent changes in the network topology caused by high mobility of the vehicles. MMFP(Multi-hop MAC Forwarding) is a unicast forwarding protocol that transport packets based on the reachability information instead of path selection or position information. However, delivering public safety messages informing road conditions such as collision, obstacles and fog through inter-vehicular communication requires broadcast rather than unicast since these messages contain information valuable to most drivers within a close proximity. Flooding is one of the simplest methods for multi-hop broadcast, but it suffers from reduced packet delivery-ratio and high transmission delay due to an excessive number of duplicated packets. This paper presents two multi-hop broadcast protocols for inter-vehicular communication that extend the MMFP. UMHB(Unreliable Multi-Hop Broadcast) mitigates the duplicated packets of MMFP by limiting the number of nodes to rebroadcast packets. UMHB, however, still suffers from low delivery ratio. RMHB(Reliable Multi-Hop Broadcast) uses acknowledgement and retransmission in order to improve the reliability of UMHB at the cost of increase in transmission delay, which we show through simulation is within an acceptable range for collision avoidance application.

• The KIPS Transactions:PartA
• /
• v.10A no.5
• /
• pp.529-538
• /
• 2003

The speedy development of the world-wide web is rapidly growing the internet-based tools for the remote instruction. In interchanging and expressing the information of one another on the web, it is produced through the form of HTML(Hyoertext Text Markup Language). However, the structural disadvantage of the HTML is becoming to require a powerful XML(eXtensible Markup Language) which can store all the sphere of data, and transform them into another form. Nevertheless, because the powerful XML(eXtensible Markup Language). However necessary that XML standard should be applied appropriately. Because existing lecture data of cyber education sites cannot be shared, the users should passively use only the functions offered by cyber school. To solve the problem of this limit, in this study, the standardized data structure for XML is defined, and system model for processing between the server and the client is provided. By storing the lecture data of cyber education sites as XML on the web, stored data came to be reused without changing on any site. In the view of Users, they could used the Internet service with equipment that they want at any place and any time. To control any kinds of CK\LMS(Cyber Lecture Management System) for Administrator and Users, we offered a variety of Multimedia applications and an easy interface and built a new style of CLMS. Therefore, by strong and extracting the data related with the virtual education of the secondary school through the form of XML, for the effective interchange and sharing of the information, maximum utilization of the information can be achieved.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.16 no.1
• /
• pp.43-48
• /
• 2006

The educational system has been changed owing to Web, which is most actively used on internet and has the characteristics of providing suitable environments for implementing constructivism study theory. WBI(Web Based Instruction), web-mediated teaching form for students at a long distance, has the advantages of possible interact between instructors and learners, offering a great variety of learning materials, and overcome the spatiotemporal restriction. This paper focuces on the construction of learning surroundings where the learner-centered, active learning can be done by design and Implementation of web based instruct system providing a sham examination with an item pool system. The web based Self-directed Learning system for word processor qualifying exams on this paper, can be mentioned as a real item pool that the question is not setting each time by the instructors but can be reused by reference on item pool bank, designed the number of question. It helps the learner Self-directed Learning study with evaluation during the web based instruct process and immediate feedback. It also provides the chance to research some similar using keyword. To sum up, this system can amplify the efficiency of study.

• Journal of The Korean Association For Science Education
• /
• v.23 no.2
• /
• pp.155-164
• /
• 2003

The purpose of the current study was to investigate the effects of explanations about physical phenomena given in non-physics textbooks on the formation of student physical conceptions. Two classes, 39 students in each, were sampled from two middle schools in Pusan, Korea, and two kinds of test tools for investigating student conceptions were developed for the study. The first test tool(a) investigated student conceptions after reading explanations about physical phenomena in non-physics textbooks, while the second(b) investigated student conceptions after reading explanations revised by physics education experts about the same physical phenomena. The two test tools were applied to each class, and for a fair invetigation, test(a) followed by test(b) was applied to one class, while test(b) followed by test(a) was applied to the other class. The results were as follows: In both classes, the students' level of understanding from explanations revised by physics education experts was significantly (p < .01) higher than that from explanations in non-physics textbooks. As such, it is feasible that false or inappropriate explanations in non-physics textbooks can cause student misconceptions. Moreover, the improper expression of physical science concepts, improper choice of scientific terms, and incorrect grammatical structures, along with the use of unsuitable examples and improper model pictures can make it difficult for students to understand physics concepts. Furthermore, differences in the terms used in physics textbook and those used in other textbooks can also confuse students' learning.

• Applied Chemistry for Engineering
• /
• v.31 no.3
• /
• pp.341-345
• /
• 2020

An in situ regeneration of activated carbon bed using an ozonated water was studied in order for avoiding the carbon loss, contaminant emission and time consuming for discharge-regeneration-repacking in a conventional thermal regeneration process. Using phenol and polyethylene glycol (PEG) as adsorbates, the adsorption breakthrough and in situ regeneration with the ozonated water were repeated. These organics were supposed to degrade by the oxidation reaction of ozone, regenerating the bed for reuse. As the number of regeneration increased, the adsorption capacity for phenol was reduced, but the change was stabilized showing no further reduction after reaching a certain degree of decrement. The reduction of adsorption capacity was due to the increase of pore size resulting in the decrease of specific surface area during ozonation. The adsorption capacity of phenol decreased after the ozonated regeneration because the in-pore adsorption was prevalent for small molecules like phenol. However, PEG did not show such decrease and the adsorption capacity was constantly maintained after several cycles of the ozonated regeneration probably because the external surface adsorption was the major mechanism for large molecules like PEG. Since the reduction in the pore size and specific surface area for small molecules were proportional to the duration of contact time with the ozonated water, careful considerations of the solute size to be removed and controlling the contact time were necessary to enhance the performance of the ozonated in situ regeneration of activated carbon bed.