• Korean Chemical Engineering Research
• /
• v.44 no.6
• /
• pp.623-630
• /
• 2006

The slag viscosity is an important factor determining the operation temperature of entrained flow type of gasifiers. The temperature of critical viscosity, $T_{cv}$, for 5 crystalline slags was predicted by empirical models and FactSage equilibrium calculations, and the validity of each method was tested. Two empirical models were employed: one using $T_h$ from the ash fusion test, and the other using the concentrations of 5 major components. The first model using $T_h$ over-predicted $T_{cv}$ by $20{\sim}100^{\circ}C$, while the model based on the slag composition under-predicted $T_{cv}$ by $80{\sim}120^{\circ}C$. In the equlibrium calculations, $T_{cv}$ was obtained from the liquidus temperature. When the 4-major component concentrations were used in the calculation, the predicted temperatures were higher than the observed. The liquidus temperature was very sensitive to the concentrations of minor components, and the addition of MgO and $Na_2O$ lowered the liquidus temperature. The results with 4 major and 3 minor components most closely described experimentally observed $T_{cv}$. In the case that a chromia refractory was used, it was shown that $Cr_2O_3$ concentration in the slag also needs to be included for more accurate prediction of $T_{cv}$.

• Journal of the Korean Society for information Management
• /
• v.20 no.1
• /
• pp.417-455
• /
• 2003

Ontologies are formal theories that are suitable for implementing the semantic web. which is a new technology that attempts to achieve effective retrieval, integration, and reuse of web resources. Ontologies provide a way of sharing and reusing knowledge among people and heterogeneous applications systems. The role of ontologies is that of making explicit specified conceptualizations. In this context, domain and generic ontologies can be shared, reused, and integrated in the analysis and design stage of information and knowledge systems. This study aims to design an ontology for international organizations. and build an Internet web retrieval system based on the proposed ontology. and finally conduct an experiment to compare the system performance of the proposed system with that of internet search engines focusing relevance and searching time. This study found that average relevance of ontology-based searching and Internet search engines are 4.53 and 2.51, and average searching time of ontology-based searching and Internet search engines are 1.96 minutes and 4.74 minutes.

• Korean Chemical Engineering Research
• /
• v.55 no.3
• /
• pp.385-394
• /
• 2017

In this study, reaction mechanism and curing characteristics of adhesives formulated with NaOH- and $H_2SO_4$-hydrolyzed chicken feather (CF) and formaldehyde-based crosslinkers were investigated by FT-IR and DSC. In addition, adhesive properties and formaldehyde emission of medium-density fiberboards (MDF) applied with the adhesives were measured. CF-based adhesives having a solid content of 40% and over were very viscous at $25^{\circ}C$, but the viscosity reduced to $300{\sim}660m{\cdot}Pa{\cdot}s$ at $50^{\circ}C$. Consequently, the adhesives could be used as a sprayable resin. Through the FT-IR spectra of liquid and cured CF-based adhesives, addition reaction of methylol group and condensation reaction between the functional groups with the use of formaldehyde-based crosslinkers were identified. From the analysis of DSC, it was elucidated for CF-based adhesives to require a higher pressing temperature or longer pressing time comparing to commercial urea-formaldehyde (C-UF) resin. MDF bonded with CF-based adhesives, which was formulated with 5% NaOH-hydrolyzed CF (CF-AK-5%) and PF of formaldehyde to phenol mole ratio of 2.5 (PF-2.5), and pressed for 8 min had higher MOR and IB than those with other CF-based adhesives. MOR and IB of MDF bonded with the CF-based adhesives regardless of formulation type and pressing time were higher than those with C-UF resin. When the values compared with the minimum requirements of KS standard, IB exceeded the KS standard in all formulations and pressing time, but MOR of only MDF bonded with CF-AK-5% and PF-2.5 and pressed for 8 min satisfied the KS standard. What was worse, 24-TS of MDF bonded with all CF-based adhesives did not satisfied the KS standard. However, MOR and 24-TS can be improved by increasing the target density of MDF or the amount of wax emulsion, which is added to improve the water resistance of MDF. Importantly, the use of CF-based adhesives decreased greatly the formaldehyde emission. Based on the results, we reached the conclusion that CF-based adhesives formulated under proper conditions had a potential as a sprayable resin for the production of wood panels.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.12
• /
• pp.19-30
• /
• 2010

Bentonite-based grout has been widely used to seal a borehole constructed for a closed-loop vertical ground heat exchanger in a geothermal heat pump system (GHP) because of its high swelling potential and low hydraulic conductivity. Three types of bentonites were compared one another in terms of viscosity and thermal conductivity in this paper. The viscosity and thermal conductivity of the grouts with bentonite contents of 5%, 10%, 15%, 20% and 25% by weight were examined to take into account a variable water content of bentonite grout depending on field conditions. To evaluate the effect of salinity (i.e., concentration of NaCl : 0.1M, 0.25M, and 0.5M) on swelling potential of the bentonite-based grouts, a series of volume reduction tests were performed. In addition, if the viscosity of bentonite-water mixture is relatively low, particle segregation can occur. To examine the segregation phenomenon, the degree of segregation has been evaluated for the bentonite grouts especially in case of relatively low viscosity. From the experimental results, it is found that (1) the viscosity of the bentonite mixture increased with time and/or with increasing the mixing ratio. However, the thermal conductivity of the bentonite mixture did not increase with time but increased with increasing the mixing ratio; (2) If bentonite grout has a relatively high swelling index, the volume reduction ratio in the saline condition will be low; (3) The additive, such as a silica sand, can settle down on the bottom of the borehole if the bentonite has a very low viscosity. Consequently, the thermal conductivity of the upper portion of the ground heat exchanger will be much smaller than that of the lower portion.

• The korean journal of orthodontics
• /
• v.38 no.4
• /
• pp.228-239
• /
• 2008

Objective: The aim of this study was to evaluate the strain induced in the cortical bone surrounding an orthodontic microimplant during insertion. Methods: A 3D finite element method was used to model the insertion of a microimplant (AbsoAnchor SH1312-7, Dentos Co., Daegu, Korea) Into 1 mm thick cortical bone with a pre-drilled hole of 0.9 mm in diameter. A total of 1,800 analysis steps was used to simulate the 10 turns and 5 mm advancement of the microimplant. A series of remesh in the cortical bone was allowed to accommodate the change in the geometry accompanied by the implant insertion. Results: Bone strains of well higher than 4,000 microstrain, the reported upper limit for normal bone remodeling, was observed in the bone along the whole length of the microimplant. At the bone in the vicinity of the screw tip, strains of higher than 100% was recorded. The insertion torque was calculated at approximately 1.2 Ncm which was slightly lower than those measured from the animal experiment using rabbit tibias. Conclusions: The insertion process of a microimplant was successfully simulated using the 3D finite element method which showed that bone strains from a microimplant insertion might have a negative impact on physiological remodeling of bone.

• Composites Research
• /
• v.35 no.1
• /
• pp.18-22
• /
• 2022

Dispersion is one of the most important factors in the manufacture of composite materials. In the manufacture of composite materials, solvents are used to better disperse the reinforcement, nano-filler in the matrix. Since dispersion is affected with solvents, it is necessary to study which solvent is adopted to get good dispersion. In this study, the dispersion behavior and solubility of graphene oxide(GO) were examined under various solvents (DMF, NMP, ethylene glycol, Acetone, DI water) to identify dispersion. As a result of UV-Vis spectroscopy absorbance measurement, it was found that DMF and ethylene glycol had the best dispersibility, whereas DI water showed the lowest dispersibility. In addition, as a result of visually observing the dispersion according to the surface tension and time, it was found that the dispersibility was excellent in the order of DI water, ethylene glycol, NMP, DMF, and acetone, which was consistent with the Hansen solubility parameter value.

• The Korean Journal of Food And Nutrition
• /
• v.15 no.2
• /
• pp.104-111
• /
• 2002

The peptidyl prolyl sis-trans isomerase (PPIase, EC 5.2.1.8) from bacillus stearothermophilus was extracted from the cells treated with by lysozyme. PPIase was purified from the cell extracts by heat treatment, ammonium sulfate precipitation, ion exchange chromatography and finally gel filtration, sodium dodecyl sulfate polyacrylamide gel electrophoresis(SDS-PAGE). The molecular weight of the purified PPIase was estimated as 18kDa by SDS-PAGE. The 39 amino acid residues from the N-terminus were determined by the protein sequencer. The enzyme showed the optimum pH at 8.0 and was stable at the range of pH 7.0∼8.0. The enzyme was considerably stable after heat treatment at 60$\^{C}$ for 30minutes, and the enzyme was quite stable up to 65$\^{C}$. The presence of the PPIase in the refolding solution accelerated the isomerization rate of the assay peptide. PPIase gene of Bacillus stearothermophilus was screened from a genomic library by plaque hybridization using the A-l primer as a probe. A PPIase positive plaque contained a 3.0kb insert of the chromosomal DNA. A 3.0kb fragment was subcloned into pUC18, resulting pPI-40. A DNA fragment encoding the N-terminal portion of the PPIase in pPI-40 was amplified by polymerase chain reaction(PCR) method using the A-1 and B-2 primers. The amplified fragment was cloned into the Sma I site of pUC18 and recombinant plasmid was designated as pSN-18. The nucleotide sequence of 167bp fragment was determined. The deduced amino acid sequence of PPIase was completely matched with the determined N-terminal amino acid sequence of PPIase B. stearothermophilus.

• Journal of Radiation Protection and Research
• /
• v.41 no.1
• /
• pp.71-79
• /
• 2016

Background: It is necessary to analyze radioactivity of naturally occurring radioactive materials (NORM) in products to ensure radiological safety required by Natural Radiation Safety Management Act. The pretreatments for the existing analysis methods require high technology and time. Such destructive pretreatments including grinding and dissolution of samples make impossible to reuse products. We developed a rapid and simple procedure of radioactivity analysis for thorium series in the products containing NORM. Materials and Methods: The developed method requires non-destructive or minimized pretreatment. Radioactivity of the product without pretreatment is initially measured using gamma spectroscopy and then the measured radioactivity is adjusted by considering material composition, mass density, and geometrical shape of the product. The radioactivity adjustment can be made using scaling factors, which is derived by radiation transport Monte Carlo simulation. Necklace, bracelet, male health care product, and tile for health mat were selected as representative products for this study. The products are commonly used by the public and directly contacted with human body and thus resulting in high radiation exposure to the user. Results and Discussion: The scaling factors were derived using MCNPX code and the values ranged from 0.31 to 0.47. If radioactivity of the products is measured without pretreatment, the thorium series may be overestimated by up to 2.8 times. If scaling factors are applied, the difference in radioactivity estimates are reduced to 3-24%. Conclusion : The developed procedure in this study can be used for other products with various materials and shapes and thus ensuring radiological safety.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.3
• /
• pp.23-30
• /
• 2003

In this study, the various load cases by specified by the IEC61400-1 international specification and GL Regulations for the wind energy conversion system were considered, and a specific composite structure configuration which can effectively endure various loads was proposed. In order to evaluate the structure, the structural analysis for the composite wind turbine blade was performed using the finite element method(FEM). In the structural design, the acceptable configuration of blade structure was determined through the parametric studies, and the most dominant design parameters were confirmed. In the stress analysis using the FEM, it was confirmed that the blade structure was safe and stable for all the considerd load cases. Moreover the safety of the blade root joint with insert bolts, newly devised in this study, was checked against the design loads and also the fatigue loads. The fatigue life for operating more than 20 years was estimated by using the well-known S-N linear damage rule, the load spectrum and Spera's empirical equations. The full-scale static test was performed under the simulated aerodynamic loads. from the experimental results, it was found that the designed blade had the structural integrity. Furthermore the measured results were agreed with the analytical results such as deflections, strains, the mass and the radial center of gravity. The studied blade was successfully certified by an international institute, GL, of Germany.

• Journal of Intelligence and Information Systems
• /
• v.28 no.1
• /
• pp.243-262
• /
• 2022

In this study, eye tracking was used for the appearance of the robot during the social robot design study. During the research, each part of the social robot was designated as AOI (Areas of Interests), and the user's attitude was measured through a design evaluation questionnaire to construct a design research model of the social robot. The data used in this study are Fixation, First Visit, Total Viewed, and Revisits as eye tracking indicators, and AOI (Areas of Interests) was designed with the face, eyes, lips, and body of the social robot. And as design evaluation questionnaire questions, consumer beliefs such as Face-highlighted, Human-like, and Expressive of social robots were collected and as a dependent variable was attitude toward robots. Through this, we tried to discover the mechanism that specifically forms the user's attitude toward the robot, and to discover specific insights that can be referenced when designing the robot.