• Smart Media Journal
• /
• v.11 no.7
• /
• pp.76-84
• /
• 2022

In Korea, where rice is the staple food, there are many cases in which the nutritional composition of food is different at the same weight, even though the same ingredients are used and the food or food name is the same. The cause is closely related to the moisture content of the food according to the cooking method and cooking process. In order to design a diet tailored to individual health and supply accurate calories and nutrients, a method of expressing food data that is not affected by the cooking process or cooking method is required. Usually, the same ingredients or foods show a lot of deviation from the nutritional components presented in the standard food database due to the difference in moisture content. For this reason, there are problems that increase the complexity of the food ingredient database and the difficulty in using it. As a method to improve these problems, we would like to propose a food data expression method based on dry weight. As an example of this, the characteristics of rice as a food material and changes in major nutritional components according to the change in moisture of various rice-processed foods made from rice were considered. In addition, as an example of how to normalize food data through this, the dry weight-based nutrition label of rice was presented.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.35 no.8
• /
• pp.1070-1075
• /
• 2006

Food materials for kimchi manufacturing were treated by ozone or gamma irradiation to reduce the number of contaminated microorganisms before the manufacturing of kimchi. Counts of total aerobic bacteria, yeast and mold were $10^6{\sim}10^7 and 10^3{\sim}10^4\;CFU/g$ in the food materials, respectively. After treatment with ozone $(3{\sim}6\;ppm), the total aerobic bacteria were reduced to 1 log cycle or more, in a dose-dependent manner. In comparison, gamma irradiation was superior to ozone treatment. Especially, irradiation of 5 kGy fully eliminated the yeast and mold attached in the food materials for kimchi manufacturing. The contents of ascorbic acid and total and reducing sugar were not affected by ozone or gamma irradiation. Taken together, it is suggested that microorganisms contaminated on materials for kimchi manufacturing could be substantially reduced by ozone (up to 6 ppm) and gamma irradiation (up to 5 kGy), without effect on the nutritional contents.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.40 no.2
• /
• pp.64-71
• /
• 2024

Purpose: The purpose of this study is to evaluate Ti-base abutment's three different heights and three different cement types on the pull-off force of zirconia-based restorations. Materials and Methods: A total of 90 fixture lab analogs were embedded in auto polymerizing resin bloack. 90 Ti-base abutments heights of 3 mm, 5 mm, 7 mm were scanned and zirconia restoration were prepared from scanned files. Zirconia restoration were cemented with three different types of cements (temporary, semi-permanent, permanent) following manufacturer's instructions. All 90 specimens were placed and tested in a universal testing machine for pull-out testing. Retention was measured by recording the force at load drop. Statistical analysis was performed using Kruskal-Wallis test for detecting whether there are any statistical significance along cement types or abutment heights. After that, Mann-Whitney test was used for figuring out differences regarding abutment height and the comparison between 3 cements. Results: Temp bond showed significantly lower pull-off force compared to Fujicem regardless of any abutment height. However, there were significant differences between Cem-implant and Fujicem in abutment height of 3 mm and 7 mm, but there was no significant difference in 5 mm. Temp bond and Cem-implant had significant differences only in abutment height of 5 mm. Conclusion: Although Ti-base abutment height did not influenced zirconia restorations' retentiveness, cement types showed significant differences.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.1819-1823
• /
• 2007

유역에서 상류 유역 또는 수변을 따라 자연 자원을 이용하여 조성되어야 할 완충지대는 비점오염의 영향을 줄이기 위한 중요한 최적 관리공법이다. 교란된 토지 피복과 수변 완충지대를 관리 및 복원할 때 같은 지형조건이라도 식생 종류, 발달정도, 토양조건에 따라 오염물 제거효과가 다를 수 있으며, 최소 완충지대 길이도 제거 오염물질 대상별로 적합하게 설계되고 해석되어야 한다. 본 연구의 목적은 용담댐 유역에서 SWAT 모델을 이용하여 식생 완충지대의 비점오염원 저감 모의 재현성을 평가하는 것이였다. 소유역의 관측값과 모델 예측값에 대한 모델의 검 보정이 선행되었으며 그 중에서 가장 높은 모델 효율을 가지는 소유역에서 three zone concept의 90m 수변완충지대를 지방하천을 경계로 하여 토지 피복도를 변화시켜 SWAT 모델에 적용하였다. 이 때 교목으로는 포플러 (Populus, 30m)을 적용하였고, 포플러의 높이 및 Leaf area index를 조정하여 관목 지대(30m)에 입력하였다. 잔디 지대(30m)는 자연초지를 선택하였다. 또한 지형변수(average slope)와 Manning's coefficient을 수변완충지대의 조건에 고려하여 변화를 주었고 이에 따른 유출량 및 유사량, T-N, T-P의 변화율을 조사하였다. 또한 5, 10, 30m의 식생 여과대를 밭 지역에만 적용하여 오염물의 저감 효율을 평가하였다. SWAT 모델은 각 소유역에서 발생된 전반적인 유출량과 수질변수의 추세를 잘 예측하였으며 정자천 소유역이 선택되었다. 모의된 완충지대에서는 연평균 940 m3/ha의 유출량이 감소되는 것으로 유사농도는 28.7 %의 저감효과를 보였다. 그러나 T-N, T-P의 농도는 오히려 증가되었는데 본 연구에서 고려된 보다 수변완충지대를 조성할 때 지하수 수위, 식생 성장변화 등과 같은 보다 정확한 설계 인자 산출 및 모델 DB 개발이 유역모델에 포함되어야 할 것으로 판단되었다.한 해결책을 얻어내는 상호보완적인 결과를 추구한다. 그가 디자인하는 작품은 전형적인 이미지를 내포하지 않는다. 즉 그의 작품은 기존의 가치와 이념적인 것은 배제하고, 창의적인 개념을 도출하였다.형모서리는 건물 특화 성격이 강하므로 불가피할 경우 소형 액센트 광고 위치를 미리 벽면으로 할애하는 것이 경관 및 입면계획에 유리한 것으로 분석되었다. 불확실도 해석모형 등의 새로운 기능을 추가하여 제시하였다. 모든 입출력자료는 프로젝트 단위별로 운영되어 data의 관리가 손쉽도록 하였으며 결과를 DB에 저장하여 다른 모형에서도 적용할 수 있도록 하였다. 그리고 HyGIS-HMS 및 HyGIS-RAS 모형에서 강우-유출-하도 수리해석-범람해석 등이 일괄되게 하나의 시스템 내에서 구현될 수 있도록 하였다. 따라서 HyGIS와 통합된 수리, 수문모형은 국내 하천 및 유역에 적합한 시스템으로서 향후 HydroInformatics 구현을 염두에 둔 특화된 국내 수자원 분야 소프트웨어의 개발에 기본 토대를 제공할 것으로 판단된다.았다. 또한 저자들의 임상병리학적 연구결과가 다른 문헌에서 보고된 소아 신증후군의 연구결과와 큰 차이를 보이지 않음을 알 수 있었다. 자극에 차이가 있지 않나 추측되며 이에 관한 추후 연구가 요망된다. 총대장통과시간의 단축은 결장 분절 모두에서 줄어들어 나타났으나 좌측결장 통과시간의 감소 및 이로 인한 이 부위의 통과시간 비율의 저하가 가장 주요하였다. 이러한 결과는 차가운 생수 섭취가 주로 결장 근위부를 자극하는 효과를 발휘하는 것이 아닌가 해석된다. 이와 같은 연구결과를 통해 생다시마를 주원료로 개발된 생다시마차와 생다시마 음료가 만성 기능성 변비 증세를 개선하는 효능이 잠재적으로 있음을 확인하였다. 그러나 생약제재의 변비약 수준으로 변비 개선 효능을 증대하기 위해서는 재료 배합비의 개선이나 대장 운동기능을 향상시키는 유효성분의 보강 등이 필요하다는 점도 알 수 있었다.더불어 산화물질 해독에 관

• Journal of Korean Society of Steel Construction
• /
• v.27 no.6
• /
• pp.493-501
• /
• 2015

Superelastic shape memory alloys (SMAs) are metallic materials that can automatically recover to their original condition without heat treatment only after the removal of the applied load. These smart materials have been wildly applied instead of steel materials to the place where large deformation is likely to concentrate. In spite of many advantages, superelastic SMA materials have been limited to use in the construction filed because there is lack of effort and research involved with the development of the material model, which is required to reproduce the behavior of superelastic SMA materials. Therefore, constitutive material models as well as algorithm codes are mainly treated in this study for the purpose of simulating their hysteretic behavior through numerical analyses. The simulated curves are compared and calibrated to the experimental test results with an aim to verify the adequacy of material modeling. Furthermore, structural analyses incorporating the material property of the superelastic SMAs are conducted on simple and cantilever beam models. It can be shown that constitutive material models presented herein are adequate to reliably predict the behavior of superelastic SMA materials under cyclic loadings.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.2 no.1
• /
• pp.1-9
• /
• 2014

In this paper, $CO_2$ amount is evaluated considering repairing timing and unit $CO_2$ amount per repair method including various stage of material manufacturing, moving, and construction. Four mix proportions with mineral admixture are considered and repairing timing/numbers are simulated based on the results from Life 365 which can handle chloride penetration. Furthermore two repair methods (simple cover concrete replacement and replacement with electro-chemical method for removing chloride content) are considered and the related $CO_2$ emissions are evaluated. From the study, the case with high W/B (water to binder ratio) ratio shows smaller $CO_2$ emission in construction stage but it increases more rapidly with increasing number of repair. $CO_2$ emission considering electro-chemical method greatly increases with the increasing unit $CO_2$ for the repairing method. The numbers of jumping step (repairing number) are evaluated to be 9 for WB37-OPC, 18 for WB50-OPC, 4 for WB40-SG, and 7 for WB47-SG respectively. RC structures with the longer maintenance free period are evaluated to be advantageous for saving $CO_2$ emission.

• Korean Journal of Materials Research
• /
• v.10 no.1
• /
• pp.34-40
• /
• 2000

The $Pb_{0.94}Y_{0.04}[(Zr_{0.6}Sn_{0.4})_{0.915}Ti_{0.085}]O_3$ ceramics which corresponded to the antiferroelectric-ferroelectric phase boundary composition were prepared for digital-type-piezoelectric/electrostrictive device application. Their dielectric, field-induced polarization (P) and strain (X) behaviors were studied with variations in sintering condition and excess PbO content. The orthorhombic structure of specimens was hardly affected either by excess PbO addition or sintering temperature. With increasing excess PbO content, grains tended to be smaller and rounded ones, and the optimum sintering temperature was lowered. Excess PbO addition stabilized the antiferroelectric phase of the specimen effectively, which was confirmed by P-E and X-E analyses. Also the digital-type-strain character was found to be enhanced despite of slight increase in phase transition (AFE-FE) field and electrical resistivity, and decrease in maximum strain. These results were explained in terms of possible lattice defects and domain wall motion.

• Korean Journal of Materials Research
• /
• v.6 no.7
• /
• pp.733-741
• /
• 1996

In this study MeV Si self ion implantations were done to reveal the intrinsic behavior of defect formation by excluding the possibility of chemical interactions between substrate atoms and dopant ones. Self implantations were conducted using Tandem Accelerator with energy ranges from 1 to 3 MeV. Defect formation by high energy ion implantation has a significant characteristics in that the lattice damage is concentrated near Rp and isolated from the surface. In order to investigate the energy dependence on defect formation, implantation energies were varied from 1 to 3 MeV under a constant dose of $1{\times}10^{15}/cm^2$. RBS channe!ed spectra showed that the depth at which as-implanted damaged layer formed increases as energy increases and that near surface region maintains better crystallinity as energy increases. Cross sectional TEM results agree well with RBS ones. In a TEM image as-implanted damaged layer appears as a dark band, where secondary defects are formed upon annealing. In the case of 2 MeV $Si^+$ self implantation a critical dose for the secondary defect formation was found to be between $3{\times}10^{14}/cm^24$ and $5{\times}10^{14}/cm^2$. Upon annealing the upper layer of the dark band was removed while the bottom part of the dark band did not move. The observed defect behavior by TEM was interpreted by Monte Carlo computer simulations using TRIM-code. SIMS analyses indicated that the secondary defect formed after annealing gettered oxygen impurities existed in silicon.

• Composites Research
• /
• v.33 no.6
• /
• pp.341-345
• /
• 2020

We propose a measurement method for evaluating constituent contents of carbon fiber/epoxy composites through a thermogravimetric analyzer (TGA). The sample used in the test was taken from a strand specimen made of carbon fiber/epoxy tow prepreg, and the change in weight of the sample over time was measured in real time. Using a field emission scanning electron microscope (FE-SEM), we examine the thermal damage condition of the carbon fiber depending on whether resin was removed or not. We find that it was possible to test even a small amount of sample when using TGA vis-à-vis using a conventional muffle furnace. In addition, TGA enables the temperature and exposure time to be controlled, allowing the constituent contents of composite materials to be efficiently and quantitatively evaluated.

• The Korean Journal of Pesticide Science
• /
• v.18 no.4
• /
• pp.330-335
• /
• 2014

This study was conducted to investigate residue levels of chlorantraniliprole and ethaboxam in inner part and outer leaves of a head-type Korean cabbage. Further, reduction of residues was measured after water washing, blanching and heat-cooking of the outer leaves. For chlorantraniliprole, residues in inner part and outer leaves were <0.01 mg/kg and 0.0757 mg/kg, respectively, in case of three-time spraying 30 days before harvest and <0.01 mg/kg and 1.19 mg/kg, respectively, in case of four-time spraying 10 days before harvest; for ethaboxam, <0.05 mg/kg and 0.216 mg/kg, respectively and <0.05 mg/kg and 1.18 mg/kg, respectively. Chlorantraniliprole and ethaboxam were not detected in inner part of the head-type Korean cabbage. Residue levels in outer leaves were very high as 10-100 fold as those in inner part of the cabbage. Therefore, there is no concern for safety of pesticide residues on kimchi prepared with the inner part of a head-type Korean cabbage. In addition, it needs to be noted that outer leaves should be carefully removed at harvest of the cabbage. Outer leaves water washed and blanched are called as Woogeogi, which is consumed after heat-cooking. In Woogeogi, residue concentrations of two compounds reduced to less than 10%, and further less than 5% by heat-cooking. This indicates that considerable amount of the test pesticide residues in outer leaves of a head-type Korean cabbage removed through water washing, blanching and heat-cooking.