• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.11a
• /
• pp.784-787
• /
• 2002

We prepared the PLT(28) thin film by using sol-gel method and investigated the structure and electrical properties of the film. With the XRD and AFM analyses, it is found that PLT(28) thin film annealed at 6sot has a complete perovskite structure and its surface roughness is about 22$\AA$. We prepared PLT(28) thin film on the Pt/TiO$_{x}$SiO$_2$/Si substrate, in which the specimen has a planar capacitor structure, and analyzed the electrical properties of PLT(28) thin film. In result, PLT(28) thin film has a paraelectric phase and its dielectric constant and loss tangent at 10kHz are 761 and 0.024, respectively. Also, the storage charge density and leakage current density of PLT(28) thin film at W are 134fC/$\mu$m2 and 1.01 $\mu$A/cm2, respectively. As a result of this, we concluded that the PLT(28) thin film is a promising material to be used as a capacitor dielectrics for next generation DRAM.M.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.7 no.2
• /
• pp.29-36
• /
• 1987

In most of the structural members with initial cracks, the strength tends to decrease as the member size increases. This phenomenon is known as size effect. Among the structural materials of glass, metal or concrete, etc., concrete represents the size effect even without initial crack. According to the previous size effect law, the concrete member of very large size can resist little stress. Actually, however, even the large size member can resist some stress if there is no initial notch. This means that the fracture mechanism of very small or very large size member follows strength criterion, but the medium size member follows non-linear fracture mechanics (NLFM). In this study, the empirical models which are derived based on nonlinear fracture mechanics are proposed according to the regression analysis with the existing test data of large size specimens for uni-axial compression test, splitting tensile test and shear test of reinforced concrete beams.

• Electrical & Electronic Materials
• /
• v.3 no.3
• /
• pp.233-241
• /
• 1990

본 연구에서는 xPb(Zn$_{1}$3/Nb$_{2}$3/)O$_{3}$-yBa(Zn$_{1}$3/Nb$_{2}$3/)O$_{3}$-zPbTiO(0.50.leq.x.leq.0.60, 0.10.leq.y.leq.0.20, 0.20.leq.z.leq.0.40)세라믹을 1050.deg.C에서 2시간동안 유지시켜 일반소성법으로 제작하였다. 시편 제작시 조성은 조성변태 상경계부근을 선택하였으며 Ba(Zn$_{1}$3/ Nb$_{2}$3/)O$_{3}$ 고용량에 따른 purochlore상의 억제 및 그 영향을 조사하고 구조적, 유전적 및 압전적 특성을 측정하였다. X-선 회절분석 및 미세구조의 관찰 결과, Ba(Zn$_{1}$3/Nb$_{2}$3/)O$_{3}$의 고용량에 따라 pyrochlore상 및 미반응 물질등은 억제되어 0.20mol 고용된 시편에서는 균질한 perovskite상이 형성되었다. Ba(Zn$_{1}$3/Nb$_{2}$3/)O$_{3}$의 고용량이 증가함에 따라 유전상수는 증가하여 0.50PZN-0.20BZN-0.30PT시편의 경우 6880.9의 높은 값을 나타내었으며 정전용량의 온도계수는 감소하여 0.383[%/.deg.C]의 양호한 값을 나타내었다. 큐리온도는 PbTiO$_{3}$의 고용량이 0.20mol에서 0.40mol로 증가함에 따라 30.deg.C에서 170.deg.C로 증가하였다. 전기기계 결합계수 (K$_{p}$), 기계적 품질계수(Qm) 및 압전전하 계수 (d$_{33}$)는 조성변태 상경계 부근의 조성에서 크게 나타났으며 0.60PZN-0.15BZN-0.25PT 시편의 경우 각각 58.5%, 120.5, 150x$10^{-12}$[C/N]의 값을 나타내었다.다.다.

• Electrical & Electronic Materials
• /
• v.5 no.2
• /
• pp.198-206
• /
• 1992

(P $b_{1-x}$L $a_{x}$)[(S $b_{1}$2/S $n_{1}$2/) $Ti_{y}$ Z $r_{1-y}$] $O_{3}$(0.leq.x.leq.0.04, 0.25.leq.y.leq.0.40) 세라믹을 1250[.deg.C]에서 2시간동안 유지시켜 일반 소성법으로 제작하였으며 조성 및 L $a_{2}$ $O_{3}$첨가량에 따른 구조적, 압전적 특성을 관찰하였다. L $a_{2}$ $O_{3}$의 첨가량이 3-4[mol%]인 경우 La-rich의 pyrochlore상이 형성되었다. 시편의 평균결정립 크기는 1-2[.mu.n]의 크기를 나타내었으며 PbTi $O_{3}$조성이 증가함에 따라 다소 감소하는 경향을 나타내었다. 각 조성의 시편에 대해 PbTi $O_{3}$ 및 L $a_{2}$ $O_{3}$의 첨가량이 증가할수록 유전상수는 증가하는 경향을 나타내었으며 상전이 온도인 큐리온도는 PbTi $O_{3}$조성이 감소할수록 L $a_{2}$ $O_{3}$첨가량이 증가할수록 감소하는 경향을 나타내었다. 압전 전하계수 및 전기기계 결합계수는 L $a_{2}$ $O_{3}$첨가량 및 PbTi $O_{3}$조성에 따라 증가하였으며 L $a_{2}$ $O_{3}$가 4[mol%]첨가된 0.10PSS-0.40PT-0.50PZ 시편에서 각각 250x$10^{-12}$[C/N], 29.7[%]의 최대값을 나타내었다. 기계적 품질계수는 L $a_{2}$ $O_{3}$첨가량 및 PbTi $O_{3}$조성이 증가할수록 감소하는 경향을 나타내었으며 0.10PSS-0.25PT-0.65PZ 시편에서 138의 최대값을 나타내었다.다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.10
• /
• pp.705-711
• /
• 2019

Dynamic behaviors of the deployable composite reflector antenna are numerically and experimentally investigated. Equations of the motion are formalized using Kane's equation by considering multibody systems with two degrees of freedom such as folding and twisting angles. To interpret structural deformations of the reflector antenna, the composite reflector is modeled using a beam model with the FSDT(First-order Shear Deformation Theory). To determine design parameters such as a torsional spring stiffness and a damping coefficient depending on deployment duration, an inverted pendulum model is simply applied. Based on the determined parameters, dynamic characteristics of the deployable reflector are investigated. In addition, its results are verified and compared through deployment tests using a gravity compensation device.

• Journal of the Korean Magnetics Society
• /
• v.26 no.1
• /
• pp.7-12
• /
• 2016

Effects of annealing of the gas-atomized Fe-9%Si-2%Cr powder which is suitable for high frequency application in mobile devices because of its high electrical resistivity were studied with an emphasis on the order-disorder phase transition. The formation of B2 ordered phase could not be suppressed during atomization process. When the powder was annealed at a temperature higher than $550^{\circ}C$ the peak diffracted from $DO_3$ phase could be detected. With increasing annealing temperature lattice parameter and coercivity decreased. An interesting phenomenon was an abrupt increment of coercivity in the powder annealed at $450^{\circ}C$. Highest permeability could be shown in the powder annealed at a relative low temperature of $150^{\circ}C$ and then the permeability decreased with annealing temperature. The above-mentioned results could be successfully explained by both the formation of $DO_3$ ordered phases and the change of electrical resistivity of the Fe-Si-Cr powder which was also originated from the phase transition.

• Journal of the Health Care and Life Science
• /
• v.9 no.1
• /
• pp.141-146
• /
• 2021

Determination of capsaicin, dihydrocapsaicin and nonivamide in pungent liquids of self-defense spray were studied. The nonivamide having almost same spicy taste with capsaicin have been containing a few amounts in natural products, it had called as synthetic capsaicin or PAVA, have used to flavorings for foodstuffs and incapacitating agents of riot controls. Nowadays, it has been occasionally found that the quality controls of a self-defense sprays were not properly due to flood of illegal self-defense sprays. Thus, the simple analytical method with gas chromatography is developed, it is identified whether the products which have contained synthetic capsaicin were marked like natural materials as well as the pungent ingredients in it obeyed with permissible concentration to human or not was investigated. Finally, the pungent components and amounts in some kinds of self-defense spray were investigated.

• Composites Research
• /
• v.34 no.3
• /
• pp.161-166
• /
• 2021

In this study, we present a research method to develop a shoe that prevents foot injury by inducing the foot pressure. An orthogonal grid sensor was used to check the foot pressure in the upright standing position, and the change in the foot pressure distribution for various conditions was compared. We checked the conditions for distributing foot pressure efficiently by changing the spring constant of the spring inserted into the sole of the shoe and the foot pressure generated with or without the arch of the insole. In order to minimize the experimental error from the randomness of the human body's behavior, it is possible to predict through foot pressure under certain conditions through finite element analysis that simulates the pressure distribution. By checking the change of foot pressure according to the number and arrangement of springs through finite element analysis, conditions were established to provide more efficient foot pressure. The result can be used for designing footwear for patients with diabetic feet.

• Journal of the Society of Naval Architects of Korea
• /
• v.60 no.2
• /
• pp.65-75
• /
• 2023

Ships operated at sea for a long time are subjected to various kinds of loads, which may cause various types of damage. Such damages will eventually reduce the strength of hull structures. Therefore, it is necessary to estimate and evaluate the residual strength and remaining fatigue life of aging ships in order to secure structural safety, establish a reasonable maintenance plan, and make a judgment of life extension. For this purpose, the corrosion damage and local denting damage should be measured, fatigue damage estimation should be performed, and material properties of aged steel should be identified. For this study, in order to investigate the mechanical properties of aged steel, steel plates were obtained from a naval ship that reached the end of her life span. The specimens were manufactured from the obtained steel plates, and static and dynamic tensile tests, fatigue tests, and metallographic tests were performed. The mechanical properties obtained from the aged steel plates were compared with those of new steel plates to quantify the aging effect on the mechanical properties of marine steel materials.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.6A
• /
• pp.1001-1011
• /
• 2006

It is a general agreement that exact statistical solutions can be found by a Monte Carlo technique. Due to difficulties, however, in the numerical generation of random fields, which satisfy not only the probabilistic distribution but the spectral characteristics as well, it is recognized as relatively difficult to find an exact response variability of a structural response. In this study, recognizing that the random field assumes a constant over the domain under consideration when the correlation distance tends to infinity, a semi-theoretical solution of response variability is proposed for general structures. In this procedure, the probability density function is directly used. It is particularly noteworthy that the proposed methodology provides response variability for virtually any type of probability density function, and has capability of considering correlations between multiple random variables.