• Journal of the korean academy of Pediatric Dentistry
• /
• v.33 no.2
• /
• pp.207-220
• /
• 2006

The newly developed equipments for the early detection of carious lesion are LFD (laser fluorescence device), Ultrasonic diagnostic system, CLSM(confocal laser scanning microscopy), QLF(quantitative light-induced fluorescence) and DIFOTI (digital imaging fiber-optic trans-illumination) system. In this study, DIFOTI system and LFD were used for the detection of early enamel caries. Twenty five primary teeth extracted from twenty one children at around the dentitional exchanging period were selected as samples. The results obtained from DIFOTI imaging and LFD measurement were compared with those of CLSM and comprehensive evaluations were made for the diagnostic capacity of each device. In vitro test, 40 sample teeth with their buccal & lingual surface formed by a window of $2{\times}3mm$ in diameter were immersed in artificial demineralizing solution for the period of 4, 8, 12 and 16 days. The results obtained from the experimental groups (DIFOTI, LFD) were compared to control group (CLSM) and we have reached to the following conclusions. 1. The sensitivity and specificity of DIFOTI system operated in oral environment was 88.2% and 76.9% respectively. 2. The sensitivity and specificity of LFD measured in oral environment was 76.5% and 69.2% respectively. 3, Regression analysis on the light transparent rate of DIFOTI showed its decrease according to the length of primary enamel decalcification performed in vitro(r=-0.96, p<0.05). 4. No statistically significant difference between LFT measurement and the length of in vitro decalcification was found in regression analysis (p>0.05). 5. The correlation coefficient of DIFOTI image transparent rate and the lesion depth of CLMS was -0.6988 (p<0.05), whereas no statistically significant difference was found for LFD measurement.

• Progress in Medical Physics
• /
• v.23 no.4
• /
• pp.279-284
• /
• 2012

The X ray has been widely used in both diagnosis and treatment. Recently, a miniature X ray tube has been developed for radiotherapy. The miniature X ray tube is directly inserted into the body irradiated, so that X rays can be guided to a target at various incident angles according to collimator geometry and, thus, minimize patient dose. If such features of the miniature X ray tube can be applied to development of X ray imaging as well as radiation treatment, it is expected to open a new chapter in the field of diagnostic X ray. However, the miniature X ray tube requires an added filter and a collimator for diagnostic purpose because it was designed for radiotherapy. Therefore, a collimator and an added filter were manufactured for the miniature X ray tube, and mounted on. In this study, we evaluated beam characteristics of the miniature X ray tube for diagnostic X ray system and accuracy of measuring the HVL. We used the Si PIN Photodiode type Piranha detector (Piranha, RTI, Sweden) and estimated the HVL of the miniature X ray tube with added filter and without added filter. Through an another measurement using Al filter, we evaluated the accuracy of the HVL obtained from a direct measurement using the automatic HVL calculation function provided by the Piranha detector. As a result, the HVL of the miniature X ray tube was increased around 1.9 times with the added filter mounted on. So we demonstrated that the HVL was suitable for diagnostic X ray system. In the case that the added filter was not mounted on, the HVL obtained from use of the automatic HVL calculation function provided by Piranha detector was 50% higher than the HVL estimated using Al filter. Therefore, the HVL automatic measurement from the Piranha detector cannot be used for the HVL calculation. However, when the added filter was mounted on, the HVL automatic measurement value using the Piranha detector was approximately 15% lower than the estimated value using Al filter. It implies that the HVL automatic measurement can be used to estimate the HVL of the miniature X ray tube with the added filter mounted on without a more complicated measurement method using Al filter. It is expected that the automatic HVL measurement provided by the Piranha detector enables to make kV-X ray characterization easier.

• Journal of agricultural medicine and community health
• /
• v.25 no.1
• /
• pp.99-112
• /
• 2000

This survey was conducted to assess the utilization of health center including health sub-center and community health post and the health service demand of residents in a urban and rural unified community. Officials in Up·Myun·Dong offices visited randomly sampled 4,027 households(4.6% of total households in unified City) which included 3,337 households in urban area(4.9% of total households) and 690 households in rural area(3.7% of total households) and interviewed with heads or housewives of the households in September, 1995. There were significant differences in health-related demographic characteristics including age-sex distribution, educational level, period of residence in the community and medical insurance status of the interviewees between urban and rural areas. Of the respondents, 64.8% in urban area and 55.6% in rural replied that they had utilized the health center in the past. The most common purpose for visiting the health center was to get vaccination in urban area and to get outpatient care in rural area. The top priority health center activity that needs to be reinforced was communicable disease control and over 90% of the respondents preferred to have mobile clinic and home health care service in were also highly demanded. Eighty-six percent of the urban respondents replied that a health sub-center must be established in urban area. In the rural area, 90.3% of the respondents replied that they wanted to maintain the health sub-center and 88.3% wanted to maintain the community health post. Along with the improvement of facilities and equipments of the health center by Rural Health Service Improvement Project, new health service programs must be developed to meet the demand of the community.

• Journal of Embryo Transfer
• /
• v.18 no.1
• /
• pp.43-50
• /
• 2003

The objective of this study was to investigate the effect of cryopreservation by slow and rapid freezing on the sperm motility index, viability and morphology of post-thaw human spermatozoa. After rapid freezing and thawing, sperm motility index was significantly higher (MOT:47.40$\pm$20.06%, VCL : 38.12$\pm$15.58 $\mu$m/s, VSL : 28.19$\pm$14.10 $\mu$m/s, VAP:33.64$\pm$15.15 $\mu$m/s, and HYP 2.77$\pm$2.71%) than slow freezing and thawing(MOT : 43.39$\pm$ 18.79%, VCL .33.91 $\pm$ 13.50 Um/s, VSL . 19.98$\pm$0.88 $\mu$m/s, VAP : 24.60$\pm$11.72 $\mu$m/s, and HYP . 1.33$\pm$1.57% ; P<0.05). But sperm Linearity(LIN) was significantly lower(28.83 $\pm$ 10.35) comparing to the slow freezing method(34.64 $\pm$ 11.36 ; P<0.05). On the other hand, significant difference were not observed MAD, WOB, DNC and DNM by slow and rapid frozen-thawed methods. After rapid freezing and thawing, sperm viability was lower(60 $\pm$ 2.2%) than slow freezing method(62 $\pm$2.1%) and sperm morphology was higher(46$\pm$7.7%) than that(44: 8.3). But there was no significantly These results indicate that rapid freezing method was positive effect of sperm cryopreservation in human.

• The Journal of Korean Society for Radiation Therapy
• /
• v.16 no.2
• /
• pp.81-89
• /
• 2004

Introduction : The setup error due to the patient and the staff from radiation treatment as the reason which is important the treatment record could be decided is a possibility of effect. The SET-UP ERROR of the patient analyzes the effect of dose distribution and DVH from radiation treatment of the patient. Material & Methode : This test uses human phantom and when C-T scan doing, It rotated the Left direction of the human phantom and it made SET-UP ERROR , Standard plan and 3mm, 5mm, 7mm, 10mm, 15mm, 20mm with to distinguish, it made the C-T scan error. With the result, The SET-UP ERROR got each C-T image Using RTP equipment It used the plan which is used generally from clinical - Box plan, 3Dimension plan( identical angle 5beam plan) Also, ( CTV+1cm margin, CTV+0.5cm margin, CTV+0.3,cm margin = PTV) it distinguished the standard plan and each set-up error plan and The plan used a dose distribution and the DVH and it analyzed Result : The Box4 the plan and 3Dimension plan which it bites it got similar an dose distribution and DVH in 3mm, 5mm From rotation error and Rectilinear movement( $0\%{\sim}2\%$ ). Rotation error and rectilinear error 7mm, 10mm, 15mm, 20mm appeared effect it will go mad to a enough change in treatment ( $2\%{\sim}^11\%$ ) Conclusion : The diminishes the effect of the SET-UP ERROR must reduce move with tension of the patient Also, we are important accessory development and the supply that it reducing of reproducibility and the move

• Bulletin of the Society of Naval Architects of Korea
• /
• v.27 no.3
• /
• pp.131-136
• /
• 1990

여러해 전부터 선박의 생산실적이나 생산성 관련 자료를 기록하고 보완하는 작업을 꾸준히 개선토록 노력해온 결과중 중요한 것 하나는, 선박의 여러 가지 설계 검토과정에서 충분히 활용할 수 있는 함축성 있고 믿을만한 형태의 생산정보를 제공해줄 수 있게 되었다는 것이라고 말 할 수 있겠다. 이러한 자료들은 생산계획상 각 단계(stage)에서의 작업량, 예상재료비와 인건비의 산출등이 포함될 수 있으며, 선박이나 해상구조물의 전반적인 설계방법론(design methodology)을 개선코자 한다면 ''생산지향적 설계(Design for Production)''의 근간이 되는 선박건조전략(build strategy), 구매정책(purchasing policy)과 생산기술(production technology)에 대한 폭넓은 지식이 한데 어우러져야 한다. 최근에는 CIMS의 일부분에서 보는 바와 같은 경영관리, 설계 및 생산지원 시스템의 도입으로 이와 같은 설계 프로세스의 추진을 가능케하고 있다. 이와 병행하여 설계를 지원하기 위한 전산기술, 특히 대화형 화상처리기술(interactive graphics)의 발달은 설계자가 선박의 형상이나 구조 배치를 여러 가지로 변화시켜 가면서 눈으로 즉시 확인할 수 있도록 설계자의 능력을 배가시키는데 크게 기여하고 있다. 여러 가지의 설계안(alternative design arrangement)을 신속히 만들어내고 이를 즉시 검토 평가할 수 있는 능력을 초기설계 단계에서 가질 수 있다면 이는 분명히 큰 장점일 것이며, 더구나 설계초기 단계에 생산관련인자를 설계에서 고려할 수 있다면 이는 더욱 두드러진 발전일 것이다. 생산공법과 관련생산 비용을 정확히 반영한 각 가지의 설계안을 짧은 시간내에 검토하고 생산소요 비용을 산출하여 비교함으로써, 수주계약단계에서 실제적인 생산공법과 신뢰성있는 생산실적자료를 기준으로 하여 총 건조비(total production cost)를 최소로 하는 최적의 설계를 선택할 수 있도록 해 줄 것이다. 이제 이와 같은 새로운 설계도구(design tool)를 제공해 주므로써 초기설계에 각종 생산관련 정보나 지식 및 실적자료가 반영가능토록 발전되었다. 본 논문은 영국의 뉴카슬대학교(Univ. of Newcastle upon Type)에서 위에 언급한 특징들을 반영하여 새로운 선박구조 설계 방법을 개발한 연구결과를 보여주고 있다. 본 선계연구는 5단계로 구분되는데; (1) 컴퓨터 그라픽스를 이용하고 생산정보 데이타베이스와 연결시켜 구조형상(geometry)을 정의하고 구조부재 칫수(scantling) 계산/결정 (2) 블럭 분할(block division) 및 강재 배치(panel arrangement)의 확정을 위해 생산기술 및 건조방식에 대한 정보 제공 (3) 상기 (1) 및 (2)를 활용하여 아래 각 생산 단계에서의 생산작업 분석(work content assessment) a) 생산 준비 단계(Preparation) b) 가공 조립 단계(Fabrication/Assembly) c) 탑재 단계(Erection) (4) 각각의 설계(안)에 대하여 재료비(material cost), 인건비(labour cost) 및 오버헤드 비용(overhead cost)을 산출키 위한 조선소의 생산시설 및 각종 품셈 정보 (5) 총 건조 비용(total production cost)을 산출하여 각각의 설계안을 비교 검토. 본 설계 방식을 산적화물선(Bulk Carrier) 설계에 적용하여 구조배치(structural geometry), 표준화의 정도(levels of standardisation), 구조생산공법(structural topology) 등의 변화에 따른 설계 결과의 민감도를 분석(sensitivity studies)하였다. 전산장비는 설계자의 대화형 접근을 용이하도록 하기 위해 VAX의 화상 처리장치를 이용하여 각 설계안에 대한 구조형상과 작업분석, 건조비 현황 등을 제시할 수 있도록 하였다. 결론적으로 본 연구는 설계초기 단계에서 상세한 건조비 모델(detailed production cost model)을 대화형 화상 처리방법에 접합시켜 이를 이용하여 여러가지 설계안의 도출과 비교검토를 신속히 처리할 수 있도록 함은 물론, 각종 생산 실적정보를 초기설계에 반영하는 최초의 시도라고 믿으며, 생산지향적(Design for Production) 최적설계분야의 발전에 많은 도움이 되기를 기대해 마지 않는다. 참고로 본 시스템의 설계 적용결과를 부록에 요약 소개하며, 상세한 내용은 참고문헌 [4] 또는 [7]을 참조 요망한다.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.31 no.4 s.54
• /
• pp.289-293
• /
• 2005

Nowadays there are many sun protection cosmetics including organic or inorganic UV filter as an active ingredient. Chemically stable inorganic sunsEreen agents, usually metal oxides, we widely employed in high SPF products. Titanium dioxide is one of the most frequently used inorganic UV filters. It has been used as pigments for a long period of cosmetic history. With the development of micronization techniques, it becomes possible to incorporate titanium dioxide in sunscreen formulations without whitening effect and it becomes an important research topic. However, there are very few works related to quantitations of titanium dioxide in sunscreen products. In this research, we analyzed amounts of titanium dioxide in sunscreen cosmetics by adapting redof titration, reduction of Ti(IV) to Ti(III) and reoxidation to Ti(IV). After calcification of other organic ingredients of cosmetics, titanium dioxide is dissolved by hot sulfuric acid. The dissolved Ti(IV) is reduced to the Ti(III) by adding aluminum metals. The reduced Ti(III) is titrated against a standard oxidizing agent, Fe(III) (ammonium iron(III) sulfate), with potassium thiocyanate as an indicator In order to test accuracy and applicability of the proposed method, we analyzed the amounts of titanium dioxide in four types of sunscreen cosmetics, such as cream, make-up base, foundation and powder, after adding known amounts of titanium dioxide $(1{\sim}25w/w%)$. The percent recoveries of the titanium dioxide in four types of formulations were in the range between 96 and 105%. We also analyzed 7 commercial cosmetic products labeled titanium dioxide as an ingredient and compared the results with those of obtained from ICP-AES (Inductively Coupled Plasma-Atomic Emission Spectrometry), one of the most powerful atomic analysis techniques. The results showed that the titrated amounts were well coincided with the analyzed amounts of titanium dioxide by ICP-AES. Although instrumental analytical methods, ICP-MS (Inductively Coupled Plasma-Mass Spectrometry) and ICP-AES, are the best for the analysis of titanium, it is hard to adopt because of their high prices for small cosmetic companies. It was found that the volumetric method presented here gat e quantitative and reliable results with routine lab-wares and chemicals.

• Geophysics and Geophysical Exploration
• /
• v.8 no.3
• /
• pp.224-231
• /
• 2005

In geophysical field surveys, commercial equipments often fail to resolve the subsurface target or even sometimes fail to be applied because they do not fit to the various field situations or the physical properties of the medium or target. We developed a geophysical measurement system, which can be easily adapted for the various field situations and targets. The system based on PXI with A/D converter and some stand alone equipment such as Network Analyzer was applied to borehole radar survey, borehole sonic measurement and electromagnetic noise measurement. The system for borehole radar survey consists of PXI, Network Analyzer, dipole antennas, GPIB interface is used for PXI to control Network Analyzer. The system for borehole sonic measurement consists of PXI, 24 Bit A/D converter, high voltage pulse generator, transmitting and receiving piezoelectric sensors. The electromagnetic noise measurement system consists of PXI, 24 Bit A/D converter, 2 horizontal component electric field sensors and 2 horizontal and 1 vertical component magnetic filed sensors. The borehole radar system has been successfully applied to detect the width of the artificial tunnel through which the borehole pass and to image buried steel pipe, while the commercial borehole radar equipment failed. The borehole sonic system was tested to detect the width of artificial tunnel and showed a reasonable result. The characteristic of electromagnetic noise was grasped at an urban area with the data from the electromagnetic noise measurement system. The system is also applied to characterize the signal distortion by induction between the electric cables in resistivity survey. The system can be applied various geophysical problems with a simple modification of the system and sensors.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.8
• /
• pp.29-37
• /
• 2019

Textile quality management targets the physical properties of fabrics and the subjective discriminations of color and fitting. Color is the most representative quality factor that consumers can use to evaluate quality levels without any instruments. For this reason, quantification using a color discrimination device has been used for statistical quality management in the textile industry. However, small and medium-sized domestic textile manufacturers use only visual inspection for color discrimination. As a result, color discrimination is different based on the inspectors' individual tendencies and work procedures. In this research, we want to develop a textile industry-friendly quality management method, evaluating the possibility of rapid color discrimination using a digital imaging device, which is one of the office-automation instruments. The results show that an imaging process-based color discrimination method is highly correlated with conventional color discrimination instruments ($R^2=0.969$), and is also applicable to field discrimination of the manufacturing process, or for different lots. Moreover, it is possible to recognize quality management factors by analyzing color components, ${\Delta}L$, ${\Delta}a$, ${\Delta}b$. We hope that our rapid discrimination method will be a substitute technique for conventional color discrimination instruments via elaboration and optimization.

• Journal of the Korean Society of Radiology
• /
• v.12 no.6
• /
• pp.737-743
• /
• 2018

Patient exposure dose exposure test, which is one of the items of accuracy control of Computed Tomography, conducts measurements every year based on the installation and operation of special medical equipment under Article 38 of the Medical Law, And keep records. The CT-Dose phantom used for dosimetry can accurately measure doses, but has the disadvantage of high price. Therefore, through this research, the existing CT - Dose phantom was similarly manufactured with a 3D printer and compared with the existing phantom to examine the usefulness. In order to produce the same phantom as the conventional CT-Dose phantom, a 3D printer of the FFF method is used by using a PLA filament, and in order to calculate the CTDIw value, Ion chambers were inserted into the central part and the central part, and measurements were made ten times each. Measurement results The CT-Dose phantom was measured at $30.44{\pm}0.31mGy$ in the periphery, $29.55{\pm}0.34mGy$ CTDIw value was measured at $30.14{\pm}0.30mGy$ in the center, and the phantom fabricated using the 3D printer was measured at the periphery $30.59{\pm}0.18mGy$, the central part was $29.01{\pm}0.04mGy$, and the CTDIw value was measured at $30.06{\pm}0.13mGy$. Analysis using the Mann - Whiteney U-test of the SPSS statistical program showed that there was a statistically significant difference in the result values in the central part, but statistically significant differences were observed between the peripheral part and CTDIw results I did not show. In conclusion, even in the CT-Dose phantom made with a 3D printer, we showed dose measurement performance like existing CT-Dose phantom and confirmed the possibility of low-cost phantom production using 3D printer through this research did it.