• Economic and Environmental Geology
• /
• v.42 no.4
• /
• pp.357-366
• /
• 2009

Since weathering weakens the rock fabric and exaggerates any structural weakness, it affects mechanical properties as well as physical and chemical properties of rock. Weathering leads to a decrease in density, strength, friction angle and cohesion, and subsequently it affects negatively on the stability of rock slope. The purpose of the study is to investigate the changes of the rock slope stability caused by discontinuities which have different weathering grades. For that, the discontinuity samples which are divided into two different weathering grades are obtained from the field and tested their mechanical properties such as JCS, JRC and residual friction angle. In order to evaluate the effects on the stability of slope due to weathering, the deterministic analysis is carried out. That is, the factors of safety for planar failure are calculated for rock masses which have two different weathering grades, such as fresh and weathered rock mass. However, since the JRC and friction angle values are widely scattered and the deterministic analysis cannot consider the variation, the factors of safety cannot represent properly the stability of the rock slope. Therefore, the probabilistic analysis has been used to consider the scattered values. In the deterministic analysis, the factors of safety for the fresh discontinuity and weathered discontinuity are 1.25 and 1.0, respectively. The results indicate the fresh discontinuities are stable for planar failure and the weathered discontinuities are marginally stable. However, the probabilities of failure for the fresh discontinuity and weathered discontinuity are 25.6% and 45.9%, respectively. This shows that both discontinuities are analyzed as unstable in the probabilistic analysis.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.5
• /
• pp.169-178
• /
• 2008

Compressive flanges of steel box girder is designed based on the ultimate strength behavior of sub-panel which is enclosed with longitudinal stiffeners and transverse stiffeners on appropriate safety factor. However, it is rational that the ultimate strength is calculated considering the various factors such as number and stiffness of longitudinal stiffener, spacing of transverse stiffener, initial deformation and residual stress distribution. In this study, an analysis program based on Folded Plate theory is developed considering the geometric effects and the material nonlinearity. The analysis program is applicated to the steel box girder bridges which is really constructed in domestic.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.25 no.4
• /
• pp.261-283
• /
• 2023

This study aimed to review the performance stability of PET (Polyethylene terephthalate) fiber reinforcing materials among the synthetic fiber types for which the application of performance reinforcing materials to fiber-reinforced concrete is being reviewed by examining short-term and long-term performance changes. To this end, the residual performance was analyzed after exposing the PET fiber to an acid/alkali environment, and the flexural strength and equivalent flexural strength of the PET fiber-reinforced concrete mixture by age were analyzed, and the surface of the PET fiber collected from the concrete specimen was examined using a scanning microscope (SEM). The changes in were analyzed. As a result of the acid/alkali environment exposure test of PET fiber, the strength retention rate was 83.4~96.4% in acidic environment and 42.4~97.9% in alkaline environment. It was confirmed that the strength retention rate of the fiber itself significantly decreased when exposed to high-temperature strong alkali conditions, and the strength retention rate increased in the finished yarn coated with epoxy. In the test results of the flexural strength and equivalent flexural strength of the PET fiber-reinforced concrete mixture, no reduction in flexural strength was found, and the equivalent flexural strength result also did not show any degradation in performance as a fiber reinforcement. Even in the SEM analysis results, no surface damage or cross-sectional change of the PET reinforcing fibers was observed. These results mean that no damage or cross-section reduction of PET reinforcing fibers occurs in cement concrete environments even when fiber-reinforced concrete is exposed to high temperatures in the early stage or depending on age, and the strength of PET fibers decreases in cement concrete environments. The impact is judged to be of no concern. As the flexural strength and equivalent flexural strength according to age were also stably expressed, it could be seen that performance degradation due to hydrolysis, which is a concern due to the use of PET fiber reinforcing materials, did not occur, and it was confirmed that stable residual strength retention characteristics were exhibited.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.93-93
• /
• 2009

본 연구에서는 EGW, FCAW 공정 적용에 따른 고강도 극후판 EH36-TMCP강 용접부의 역학적 거동 및 파괴인성 $K_{IC}$ 을 규명하기 위해, 먼저 열분포, 열탄소성 수치해석을 통하여 용접부의 역학적 거동(용접잔류응력, 소성변형율 등의 크기, 분포, 발생기구)을 고찰하였다. 그리고 이때 얻어진 잔류응력을 초기응력으로 하여, 잔류응력과 외력의 복합하중에 대한 파괴인성 $K_{Ic}$ 특성을 해석하였다. 용접공정별 균열이 존재하는 용접부의 파괴기준을 살펴보면, EGW용접부의 경우가 FCAW용접부의 경우에 비해 균열의 성장이 다소 용이하여 $K_{IC}$ 값이 다소 낮게 나타났다. EGW용접부의 파괴인성 $K_{IC}$ 경우 중첩된 경우(복합하중)가 순수 외력만 작용하는 경우보다 파괴 인성치가 다소 감소하는 경향을 보이고, a/W가 작을 경우 중첩의 경우가 순수 외력만의 경우보다 파괴인성치 차이가 크나, a/W가 증가함에 따라 그 차이가 점차 없어지는 것으로 나타났다. 반면, FCAW용접부의 경우 균열길이가 작은 범위에서는 중첩된 경우가 순수 외력만 작용 할 경우보다 파괴 인성치가 다소 증가함을 보이지만, a/W가 증가함에 따라 순수 외력만의 작용의 경우와 중첩의 경우의 파괴인성 차이가 없는 것으로 나타났다.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.6
• /
• pp.535-543
• /
• 2013

The objective of this study was to analyse the residual stress in Larix kaempferi board during and after kiln-drying. The boards were primarily intended for using as laminar of cross laminated timber (CLT). In this study, the equivalence of moisture content by equalizing treatment was proved and reduction of residual stress by conditioning treatment was quantified. Prong test and slice test were carried out to analyse the residual stress in wood during drying. Transverse casehardening was measured immediately after making prong sample. Residual stress of four parts in wood from surface to center was analyzed quantitatively based on elastic deformation after just cutting slices from board. Tensile stress and compressive stress on the surface of board during drying did not exceed 2.2 MPa when boards were dried by kiln-drying schedule of T10-C4 and T12-D5. Because the tensile strength and compressive strength of transverse direction of Larix kaempferi lumber are 2.65 MPa and 4.60 MPa, application of more severe drying schedule can be recommended. Cup and twist were reduced by about 40% by equalizing and conditioning treatments after drying.

• Journal of the Korean Ceramic Society
• /
• v.36 no.1
• /
• pp.61-68
• /
• 1999

To analyze several defects and residual stress in sintering of layer structure materials, multiayer materials with TZP/SUS and ZT/SUS, and bilayer materials with porcelain/alumina and porcelain/Y-TZP were fabricated by sintering method. Multilayer materials prepared by pressureless sintering show the sintering defect such as warping, splitting, cracking originated from the difference of sintering shrinkage between each layer, which could be controlled by the adjustment of number and thickness in interlayer. In tape casting, a certain pressure given during sintering relaxed the sintering defects, specially warping. The residual stress in bilayer was examined with Vickers indentation method. A small tensile stress in porcelain/alumina and a large compressive stress in porcelain/Y-TZP were generated on the porcelain interface due to the thermal expansion mismatch, which affected the strength of bilayer materials. As a consequence, the sintering defects of multilayer materials and the residual stresses of bilayer materials were dominantly influenced on material design and starting material constants.

• Journal of Food Hygiene and Safety
• /
• v.8 no.4
• /
• pp.215-223
• /
• 1993

Chloramphenicol (CAP) is a very effective broad-spectrum antibiotic which had been widely used in animal production. However, the drug is not approved in many countries for use in food-producing animals because of its potential toxicity and the possibility of residues in food products. In this study, a modified microbiological assay was developed for the sensitive detection of CAP residues in meat and milk. The method was characterized by the extraction of CAP with ethyl acetate, addition of $0.15\;\mu\textrm{g}$ oxytetracycline/ml in the phosphate buffer diluent (pH 6.0), a luteus ATCC 9341. The lowest levels of CAP detected in muscle tissues and milk were $0.025\;\mu\textrm{g}/ml\;and\;0.05\;\mu\textrm{g}/g$, respectively. Recovery rates free CAP from milk were 68.5%, from bovine muscle 65.1%, from swine muscle 63.8%, and from chicken muscle 59.4%, respectively, and the coefficients of variation were 1.8~15.1%. The results showed that the detection limits of CAP residues in animal products could significantly be improved by the modified microbiological assay than the conventional ones.

• The Korean Journal of Rheology
• /
• v.9 no.1
• /
• pp.33-39
• /
• 1997

PCL, MDI, BD 및 DMPA를 이용, 폴리우레탄(PU)을 ionomer 및 nonionomergudxo 로 제조하였으며 이때 연질성분의 함량(SSC) 및 길이가 PU의 기계적, 동적기계적 특성은 물론 형상기억특성에 미치는 영향을 연구하였다. Ionomer는 nonionomer에 비하여 경도, 탄 성율 및 강도가 모두 우수하였으며 그 효과는 실온에서 경질성분의 함량(HSC)이 높은 PU 일수록 보다 뚜렷하였는데 이는 HSC가 증가할수록 ion 중심의 농도가 증가하며 ion 중심간 의 Coulob 력이 고온보다 실온에서 보다 큰데 기인하는 것으로 해석하였다. 반복인장하중실 험에서 ionomer는 nonionomer에 비해 회복변형이 크고 잔류변형이 작았는데 이는 ionomer 의 고무탄성율이 보다 큰 데 기인한 것으로 해석하였다. 나아가 재료의 형상기억거동은 기 본적으로 탄성율의 온도의존성에 크게 의존함을 알수있었다.

• Journal of Conservation Science
• /
• v.30 no.3
• /
• pp.287-298
• /
• 2014

This study investigates the material properties of the traditional bricks used in the royal tomb of King Muryeong. Compressive strengths, thermal conductivities, absorptance and the rate of residual moisture are measured by non-destructive experiments. Compressive strength of the traditional bricks is estimated by using the ultrasonic wave velocity and the absorptance. Based on the experimental results, the predicted compressive strengths using the ultrasonic wave velocity are unsuitable for the traditional bricks due to the rough surface and thickness variation of the specimens. The strengths using the absorptance are more suitable than those using the velocity because the predicted average strengths (28.69 MPa ~ 33.19 MPa) are close to building materials like normal strength concrete. In addition, the methods using the absorptance are not influenced by surface and thickness conditions of the specimens. The average thermal conductivities of the bricks measured by using Mathis TCi are close to those of soils (1.58 W/mK). The absorptance and the rate of residual moisture of the bricks are 1.6 % ~ 15 %, 0 % ~ 0.7 %, respectively.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.11a
• /
• pp.53-53
• /
• 2011

자동차용 천연가죽 시트의 제조 공정에서 크롬과 비크롬 Metalic 탄닝제, 식물성 탄닝제, 신탄(Syntan) 및 가지제(Fatliuor) 등의 종류와 함량에 따른 인장강도, 신장율, 정하중 신율, 잔류줄음율 등을 측정하여 특정하중에 따른 콜라겐 섬유 조직의 영구변형율과의 상관관계를 비교 분석해본 결과, 크롬 및 비크롬계 탄닝제에 비해 식물성 탄닝제를 적용하였을 때 조직의 변형율이 적었으며, 리틴닝 공정에서 아크릴계, 레진계 및 단백질계 신탄을 혼합 적용하였을 때 가죽의 배(Belly)부위의 물성 균일화 효과가 우수하였으며, 음이온성 가지제 9%를 사용하여 가죽에 유연성을 부여함으로써 조직이 치밀하고 변형율이 감소되어 내구성이 우수한 결과를 나타내었다.