• Journal of the Korea Convergence Society
• /
• v.9 no.4
• /
• pp.1-7
• /
• 2018

Electric motors for electric vehicles differ in efficiency characteristics depending on the operation modes, studies for evaluating high efficiency characteristics in low speed and high speed operation modes are very important. Therefore, it is necessary to design method that can change the high torque, high output density, and high efficiency characteristics of driving motors for electric vehicles. In this paper, the diameter ratio of stator and rotor for the interior permanent magnet synchronous motor is change of designed 0.62, 0.65, and 0.68, respectively, and the efficiency characteristics of the entire operation section, average efficiency characteristics of the city driving modes and express highway driving modes are analyzed. As a result of analyzing the efficiency characteristics of the entire operating section, it was confirmed that as the diameter ratio increases, the high efficiency section moves to the low speed and low torque section and the high efficiency section moves to the high speed and low torque neighborhood as the diameter ratio decreases. As a result of analyzing the average efficiency characteristics in the city driving modes and express highway driving modes, the average efficiency of 0.68 model is analyzed to be more efficient than the 0.63 and 0.65 model ratio, and it is confirmed that it is suitable for city driving modes and express highway driving modes.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2009.05a
• /
• pp.1807-1811
• /
• 2009

홍수기 유량측정에 있어서 가장 큰 어려움이었던 유속측정의 정확성을 확보하고 실무자의 안전성을 보장하기 위한 기본 취지에서 1993년 시작된 "대하천 유량 자동측정 설비개발"이라는 연구 주제하에 비접촉식 유속측정 기법에 대한 연구를 수년간 연구개발을 거듭한 결과물인 전자파표면유속계를 1999년도에 상품화하여 현재 국내에서 홍수유속측정 설비로 이용되어지고 있다. 현장에서 유량측정업무에 종사하는 실무자들은 홍수유량측정에 비하여 훨씬 간편함을 몸소 느끼게 되었고, 상품화보급이 시작된지 수년이 지난 상태에서는 더욱 성능이 개선된 전자파표면유속계가 개발되기를 기대하였다. 무엇보다도 홍수기에 유량측정시 기존의 유속측정 방법과 같은 방식으로 각 측선마다 전자파표면유속계를 설치해야하는 번거로움을 피력하였다. 기존의 전자파표면유속계는 하천을 가로지르는 교량위에서 흐름방향에 나란히 측정하는 조건을 고려하였기 때문에 이와 같은 편각인 상태의 유속측정은 검토하지 않았다. 이와 같은 사용자의 요구에 대하여 한국수자원공사에서는 홍수기 유량측정시의 사용자 편의성을 증대하기 위하여 성능개선 작업에 착수하여 편각측정용 전자파표면유속계를 개발하였다. 편각측정의 주된 목적은 전자파표면유속계를 모든 측선에 설치하지 않고 한 지점에서 편각(oblique angle)으로 여러 측선의 유속을 측정함으로써 유속측정의 효율성을 증대시키는 것이다. 전자파표면 유속계에서의 편각 측정은 하천의 유속 방향을 기준으로 정면에서 측정하면 수평 편각이 0도가 되며 좌우로 안테나를 회전하여 움직인 각도가 측정 편각으로 결정된다. 전자파의 물리적 특성 때문에 편각이 증가하면 반사된 신호의 수신 크기가 감소하여 측정이 불가능하게 된다. 이러한 문제를 최대한 극복하는 것이 본 연구의 중점 개선사항이다. 이를 통하여 전자파표면유속계를 교량의 임의 지점에 설치하여 좌우로 편각 $20^{\circ}$에 이르는 범위의 유속을 측정하고자 목표로 하였다. 홍수시의 현장 측정 환경은 열악하기 때문에 정확한 측정을 조건으로 측정자에게 최대한의 편리함과 신속한 측정 환경을 제공해야 효과적인 업무수행이 가능하다. 이러한 편각 측정을 가능토록 하기 위해서는 유속측정시 송신되는 전자파의 출력을 기존의 시스템보다 보다 높게 발사하여야 하며 안테나의 수신감도 및 지향성이 개선되어야 한다. 이를 위해서 안테나 형태에 있어 기존 전자파표면유속계와의 차이점은 기존안테나는 파라볼릭 형상이었으나 신규 제작된 안테나는 평면안테나로 이러한 형태의 개선를 통해 안테나 특성 및 구조적인 차이를 유도하였다. 두 가지 안테나 사양 각각 장단점이 있으나 가장 큰 차이점은 빔폭 특성에서 평면 안테나가 우수하며 수신 감도를 향상시킬 수 있다는 강점이 있다. 특히 Tx/Rx 분리의 평면안테나 구조는 파라볼릭 안테나에서 불가능한 기능으로서 편각측정으로 인한 수신감도의 저하의 문제를 해결하기 위한 개선조치이었다. 성능개선 제작된 편각측정용 전자파표면유속계를 이용하여 일반하천의 홍수유속에 대한 편각측정 실험을 안성천에서 실시한 결과 유속 약 1.7 m/s 인 상황에서 편각 $20\;^{\circ}$ 까지 편각 $0\;^{\circ}$일때와 유사한 측정 성능을 보였다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.2
• /
• pp.189-196
• /
• 2001

Photoelasticity is one of the most widely used methods for whole field stress analysis. In photoelasticity, the difference and the directions of the principal stresses we given isochromatic and isoclinic fringe patterns. Conventionally, principal stress directions are measured manually by relating the polarizer and analyzer of a plane polariscope at the same time. This is known to be the Tardy compensation method. This measurement can be very tedious and time consuming in whole field analysis. It is not possible to separate isoclincs from photoelastic fringes by conventional photoelastic technique. In this study, photoelastic theory is represented by Jones matrices and 4-steps and 8-steps phase shifting methods are described A feasibility study using computer simulation is done to separate isoclincs and isochomatics from photoelastic fringes of a circular disk under diametrical compression. Fringe patterns of the disk are generated using stress optic law. The magnitudes of isoclincs and isochromatics obtained from 8-step phase shifting method are compared with those of theories. From computer simulation, it is verified to separate isoclincs and isochomatics from photoelastic fringes.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.10
• /
• pp.121-127
• /
• 2018

A system for diagnosing surface defects of long and large pipe inner overlay welds, 1m in diameter and 6m in length, was developed using a Liquid Penetrant Test (PT). First, CATIA was used to model all major units and PT machines in 3-dimensions. They were used for structural strength analysis and strain analysis, and to check the motion interference phenomenon of each unit to produce two-dimensional production drawings. Structural strength analysis and deformation analysis using the ANSYS results in a maximum equivalent stress of 44.901 MPa, which is less than the yield tensile strength of SS400 (200 MPa), a material of the PT Machine. An examination of the performance of the developed equipment revealed a maximum travel speed of 7.2 m/min., maximum rotational speed of 9 rpm, repeatable position accuracy of 1.2 mm, and inspection speed of $1.65m^2/min$. The results of the automatic PT-inspection system developed to check for surface defects, such as cracks, porosity, and undercut, were in accordance with the method of ASME SEC. V&VIII. In addition, the results of corrosion testing of the overlay weld layer in accordance with the ferric chloride fitting test by the method of ASME G48-11 indicated that the weight loss was $0.3g/m^2$, and met the specifications. Furthermore, the chemical composition of the overlay welds was analyzed according to the method described in ASTM A375-14, and all components met the specifications.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.5
• /
• pp.215-222
• /
• 2018

Recently, various motion beds have been actively developed and popularized. The motion bed has the functions of height adjustment, back plate rising, knee lifting, tilt function and left / right rotation, and the remote control can conveniently be used by the patient himself or the caregiver to move the patient. However, since the medical bed for use does not have a function of preventing pressure ulcers, exchanging sheets, and transferring patients, it is necessary to disperse body pressure by using a pressure ulcer prevention matrix to prevent pressure ulcers. However, it is accompanied by muscle strength and hard work, and nurses are avoiding difficult nursing care. In this study, we developed the first prototype in the world and confirmed that the system works normally with the goal of developing multifunctional beds that automatically perform the prevention of bed sores, the exchange of sheets and the transfer of patients in order to facilitate such nursing work. It is anticipated that the proposed multifunctional motorized bed in the future will be a model of a medical robot for smart healthcare.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.45 no.5
• /
• pp.21-27
• /
• 2008

Despite recent studies on development of pulse diagnosis systems and needs for commercializing them, the reproducibility is one of the most controversial issues as ever. Because the pulse pressure value, which is one of the important parameters to evaluate reproducibility, is very vulnerable to moving artifacts, the reproducibility can not be obtained easily. In this paper, we suggested a moving artefacts detection system for a pulse diagnosis system so that a pulse diagnosis system can be robust to theses kinds of artefacts by excluding the contaminated parts from the pulse wave signal to be analyzed. This moving artifacts detection system was designed to consist of a three-axis accelerometer, an electromyography amplifier and a two-axis tilt sensor. To assess the suitability of the system, we examined the characteristics of each sensor's output signals with regard to the three specific motions such as extension, flexion and rotation. And, we also examined the each sensor's response to the high-frequency and low-frequency moving artifacts while the pulse wave signal was acquired from a pressure sensor for the pulse diagnosis. From these results, we could find that the response to subject's motions would be reflected in electromyography signal first, in accelerometer signals and in tilt sensor sequently. And, the facts that a stable pulse wave can be acquired in two seconds after high frequency or low frequency motions ended, were also found. Consequently, based on these findings, we set up some rules on the moving artifacts detection and designed an algorithm which is fit for our moving artifacts detection system.

• Journal of Broadcast Engineering
• /
• v.15 no.2
• /
• pp.163-172
• /
• 2010

The free viewpoint video delivers an active contents where users can see the images rendered from the viewpoints chosen by them. Its applications are found in broad areas, especially museum tour, entertainment and so forth. As a new free-viewpoint application, this paper presents a stereoscopic free-viewpoint TIP (Tour Into Picture) where users can navigate the inside of a single image controlling a virtual camera and utilizing depth data. Unlike conventional TIP methods providing 2D image or video, our proposed method can provide users with 3D stereoscopic and free-viewpoint contents. Navigating a picture with stereoscopic viewing can deliver more realistic and immersive perception. The method uses semi-automatic processing to make foreground mask, background image, and depth map. The second step is to navigate the single picture and to obtain rendered images by perspective projection. For the free-viewpoint viewing, a virtual camera whose operations include translation, rotation, look-around, and zooming is operated. In experiments, the proposed method was tested eth 'Danopungjun' that is one of famous paintings made in Chosun Dynasty. The free-viewpoint software is developed based on MFC Visual C++ and OpenGL libraries.

• The Journal of the Acoustical Society of Korea
• /
• v.21 no.5
• /
• pp.471-477
• /
• 2002

Recently, lip-reading has been studied actively as an auxiliary method of automatic speech recognition(ASR) in noisy environments. However, almost of research results were obtained based on the database constructed in indoor condition. So, we dont know how developed lip-reading algorithms are robust to dynamic variation of image. Currently we have developed a lip-reading system based on image-transform based algorithm. This system recognize 22 words and this word recognizer achieves word recognition of up to 53.54%. In this paper we present how stable the lip-reading system is in environmental variance and what the main variant factors are about dropping off in word-recognition performance. For studying lip-reading robustness we consider spatial valiance (translation, rotation, scaling) and illumination variance. Two kinds of test data are used. One Is the simulated lip image database and the other is real dynamic database captured in car environment. As a result of our experiment, we show that the spatial variance is one of degradations factors of lip reading performance. But the most important factor of degradation is not the spatial variance. The illumination variances make severe reduction of recognition rates as much as 70%. In conclusion, robust lip reading algorithms against illumination variances should be developed for using lip reading as a complementary method of ASR.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.11
• /
• pp.205-210
• /
• 2014

This is concerned with the technology to display the design on Porcelain and adjust malfunction for moving effect and light intensity by curator. More precisely, the technology makes it possible that the porcelain is connected to Light module which is the device for controlling light emission and rotating rolling plate, etc that are connected to LED light module, optical fiber and controller that is for scenario from the given storytelling. In addition, with a WiFi portable device (Smart-phone, other mobile device). equipped with a scenario programs, information for operation, failure and malfunction can be obtained and analyzed in real-time, and menu color and alarm is alerted when the displaying design is in abnormal status, which makes the early reactions to the status. Furthermore, the collected data can be sent through WiFi network to the device and PC managed by the curator specialized in managing the design on the Porcelain, thus the technology could help the curator who have less knowledge about moving pattern on the Porcelain. There is always a possibility of malfunction due to various condition that are caused by wring-harness when modules are wired-connected. In this research, in order to overcome this problem, we propose a system configuration that can do monitoring and diagnosis with a device for collecting data from LED control module, Light emission sensor and a personal WiFi device. Also, we performed connection between optical Fiber and LED and interlock for the system defined by the definition for information and storytelling scenario.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.26 no.6
• /
• pp.599-609
• /
• 2008

Development of computer and electronic technology leads innovative progress in spatial informatics and successful commercialization. Geospatial information technology plays an important role in decision making in various applications. However, information display media are two-dimensional plane that limits visual perception. Understanding human visual processing mechanism to percept stereo vision makes possible to implement three-dimensional stereo image display. This paper proposes on-the-fly stereo image generation methods that are involved with various exterior and camera parameters including exposure station, viewing direction, image size, overlap and focal length. Collinearity equations and parameters related with stereo viewing conditions were solved to generate realisitc stereo imagery. In addition stereo flying simulation scenery was generated with different viewing locations and directions. The stereo viewing is based on the parallax principle of two veiwing locations. This study implemented anaglyphic stereogram, polarization and lenticular stereo display methods. Existing display technology has limitation to provide visual information of three-dimensional and dynamic nature of the real world because the 3D spatial information is projected into 2D plane. Therefore, stereo display methods developed in this study improves geospatial information and applications of GIS by realistic stereo visualization.