• Journal of the korean Society of Automotive Engineers
• /
• v.6 no.4
• /
• pp.18-28
• /
• 1984

디이젤 엔진은 피스톤이 실린더 내를 왕복 운동하면서 압축행정에서 연료의 연소에 의해 발생된 고열을 받아 고온에서 작동되기 때문에 피스톤 헤드에서 받은 열은 속히 아래부분으로 전달시 키고 동시에 실린더 벽으로 전달되게 하여야 한다. 여기서 열이 문제가 되는 요소를 생각해 보면, (1) 고압 : 연소 최고폭발압력이 높기 때문에 압력상승률도 커져 격렬한 연소상태가 된다. (2) 고온 : 격심한 가스 유동과 실린더 직경이 크기 때문에 피스톤 헤드부의 온도가 높아진다. (3) 연소생성물 중에 엔진 및 윤활유에 악 영향을 주는 성분이 많다. (4) 경량, 저가격 구조 때문에 열적 및 역학적 변형이 일어나기 쉽다. (5) 사용조건이 가혹해 연료가 이상 현상을 가져온다. 위의 요소들을 가지고 온도의 분포, 열의 전달과정, 피스톤 냉각 등에 대해서 알아본다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.1
• /
• pp.92-99
• /
• 2006

The swirl ratio of a charge in the cylinder was estimated by calculating the ratio of the rotary speed of charge which could be simulated from the rotary speed of paddle in the swirl measurement apparatus, to the engine speed which could be calculated by measuring intake air flow rate. The automation of the swirl ratio measurement for cylinder head was achieved by controling both valve lift in cylinder head and a suction pressure of surge tank using two step-motors. The number of measurement position for calculating mean swirl ratio was varied by adjusting the interval of valve lift. The mean swirl ratio with varying the number of measurement position showed nearly constant value. Two measurement methods for measuring the swirl ratio were compared, one was to control the suction pressure of the surge tank with PID (proportional, integral, differential) mode with by-pass valve controlled by the step motor and the other did not control the surge tank pressure by fixing the by-pass valve. The difference of the mean swirl ratio between the two measurement methods showed nearly constant value with varying the number of measurement position. This means that the w/o PID control method could be preferred to the PID control method which has been used, due to the simpleness of the swirl measurement.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 2003.05a
• /
• pp.118-122
• /
• 2003

본 연구를 시물레이션방법을 이용한 실린더 헤드라인 생산설비의 적정계획 및 성능산정을 위해 가용한 생산설비의 자료들로부터 요구되는 생산능력을 만족하는 생산설비를 구성한다. 구성된 설비들은 가용한 생산설비 운영조건을 고려한 가상의 시물레이션 모델로 구축하여 생산설비의 적정 구성 및 공정간의 재고 등을 산정한다. 시스템 성능 산정을 위해 본 연구에서는 AutoMod 시물레이터를 이용하여 실린더 헤드라인의 생산설비계획 문제에 적용한다. 본 연구는 다수의 생산설비를 이용한 설비계획 연구시 사전 분석과 능력산정 및 기존의 설비 운영 조건에 따른 생산능력산정에 유용할 수 있으며 3차원 동영상으로 분석 결과를 제시할 수 있다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.5
• /
• pp.178-187
• /
• 1997

For the experimental measurement of heat flux of DI diesel engine combustion chamber, the instantaneous temperature probes and data acquisition system were developed. By the analysis of measured temperatures at the cylinder head, the temperature at the point 3 which is located between intake and exhaust valve was higher than that of the other points. Temperatures at the point located mear the exhaust valve were higher than those of intake valve. The instantaneous and mean temperature at the cylinder head increases proportionally to the increase of the engine speed, while the temperature swing varies inversely. Temperature swings have influence on the maximum heat flux values from gas into head surface. It has been verified that these probes and data acquisition system perform well by the comparison of the trend of instantaneous temperature variation with that of measured combustion chamber pressure variation with respect to crank angle. It is presumed that these probes could be used in the measurement of other parts of combustion chamber as piston, cylinder wall etc. for the future study.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.5
• /
• pp.48-57
• /
• 1994

The specific power output and thermal effeciency of any two-stroke engine are dependent on its scavenging behavior. Among the many factors which influence on the scavenging process, the cylinder head shape is one of the important factor. Hence in this study three different type models of cylinder head shape which are the cylindrical, the spherical and the arbitrary shape are studied to show the effects of the turbulent scavenging process in the cylinder with one inlet port, two side ports and one exhaust port. A modified version of KIVA-II which strip out of or add planes of cells across the mesh above the piston for flow simulation of two-stroke engine is used. The $k-{\varepsilon}$ turbulent model is used. The results show that the flow in a two-stroke engine cylinder of the spherical head shape among the three different type model is a desirable for efficient scavenging.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.5
• /
• pp.187-196
• /
• 1996

In this study, 3-dimensional finite element model of a diesel engine cylinder head was made to accomplish heat transfer analysis and also thermal stress and deformation analysis. Heat release analysis and Nusselt-Reynolds correlations were applied to determine the convective boundary conditions which are required for heat transfer analysis to calculate temperature distribution. Thermal stress distribution was also investigated from heat transfer analysis results. Steady state temperature and heat flux were measured by using K-type thermocouples and then compared with numerical results to give a guarantee for the propriety of numerical analyses.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.3
• /
• pp.160-165
• /
• 2007

Exhaust manifold is generally subjected to thermal cycle loadings ; at hot condition, large compressive plastic deformations are generated, and at cold condition, tensile stresses are remained in highly deformed critical zones. These phenomena originate from that thermal expansions of the runners are restricted by inlet flange connected to the cylinder head, because the former is less stiff than the latter and, the temperature of the inlet flange is lower than that of the runners. Therefore, due to the repetitions of thermal deformation, leakage problems could be occur between inlet flange and cylinder head. In this study, we obtained pressure distributions along gasket bead lines from the finite element analysis and compared to the test results. It shows a good agreement between numerical and experimental results.

• Journal of the Korea Society for Simulation
• /
• v.17 no.2
• /
• pp.1-12
• /
• 2008

The major components of an engine are the cylinder block, cylinder head, crankshaft, connecting rod, and camshaft, which are more popularly known as the 5 C's. Thus, the engine shop usually consists of six sub-lines, including five machining lines and one assembly line. The flow line is the typical concept of the layout when the engineer designs the engine shop. This paper introduces a simulation study regarding the new crankshaft machining line in a Korean automotive factory. The major factors for designing the machining line are considered, and their effects on the system performance are evaluated with a three-dimensional(3D) simulation model that is developed with $QUEST^{(R)}$. The initial layout is analyzed using the simulation model, and we suggest some ideas for improvement.

• Journal of the Korean Institute of Gas
• /
• v.23 no.4
• /
• pp.40-45
• /
• 2019

This paper is a purpose to study the failure example for heavy-duty vehicle fire. The first example, the researcher found the engine over-heating phenomenon causing a coolant leakage by the sealing poor of head-gasket because of D-ring part deformation contacting with cylinder liner top-part and cylinder head. He certified a fire breakout by short transferred to surrounding wiring of air-cleaner. The second example, a brake lining by return fault of break operating S cam causing with much wear of a rear 4 wheel brake lining repeatably was worn by friction. In the long run, it became the cause of fire. The third example, the researcher knew the fire cause was came about the short of wire by overload of tilting motor when the driver tilted up the cap to inspect a engine. Therefore, a heavy-duty fire must minimize the fire occurrence by thorough controlling.

• CDE review
• /
• v.2 no.1
• /
• pp.33-36
• /
• 1996

승용차 산업과 같이 정밀 부품이 요구되는 산업에 있어서 가장 기초가 되고도 중요한 것은 시작금형에 해당하는 정밀 목형 제작이라고 할 수 있다. 부품의 개발은 일반적으로 설계과정, 도면화 과정, 시제품 개발과정, 시제품 성능시험과정, 양산체제 구축과정 등의 순서를 밟는다. 이 과정 중에서 시제품 개발과정은 설계에 의해서 만들어진 제품이 실제 설계자의 의도와 일치하는지를 확인하는 과정이다. 이 과정에서 부품 간의 간섭, 치수나 형상의 확인, 기능 혹은 성능상의 문제점 등을 검토하여 양산체제시에 발생할 수 있는 문제점 등을 최대한 제거하여야 한다. 그런데 시제품 제작에 걸리는 기간이 개발과정 중에서도 비교적 큰 부분을 차지하고 있어 이의 단축이 시급한 실정이다. 현재 시제품 제작업체들 중에서 프레스 금형을 위한 판넬 수지가공에는 3D CAD/CAM을 많이 적용하고 있지만, 주물 소재용 목형제작은 대부분 숙련된 기술자의 수작업에 의존하고 있다. 따라서 개발기간 단축과 비용절감이라는 완성차 업계의 요구와는 거리가 있는 실정이다. 당사는 이미 실린더 헤드, 매니홀더, 트랜스밋션 케이스, 헤드커버, 실린드블럭 등 자동차 엔진의 핵심부품들의 목형을 3D CAD/CAM을 이용하여 생산하고 있기 때문에 이중 트랜스밋션 케이스의 목형제작 과정을 소개하고자 한다.