• Korean Chemical Engineering Research
• /
• v.47 no.6
• /
• pp.740-746
• /
• 2009

In the present study, the drowning-out crystallization of L(+)-calcium lactate was investigated in order to develop the crystallization separation process. The crystallization of the calcium lactate was induced by injecting the alcoholic anti-solvent into the aqueous solution of calcium lactate and the control of the calcium lactate crystal size during the crystallization was primarily investigated under the consideration of the anti-solvent species, anti-solvent composition and agitation speed as the key operating factors. Alcohols of methanol, ethanol, n-propanol and i-propanol were used as the anti-solvent for the drowning-out crystallization. Prior to the crystallization experiment, the solubility of calcium lactate in the water-alcohol mixture was measured along with the variation of the alcohol species and composition, which was necessary to estimate the supersaturation level of the crystallization. By the drowning-out crystallization, the calcium lactate crystals of the fabric shape were obtained. Using the ethanol as the antisolvent, the fabric crystals close to the needle shape were produced. However, the hairy crystals were obtained by using the propanol as the anti-solvent. Due to such morphological features, the crystals was highly apt to form the aggregates. The aggregation of the crystals was intensified as increasing the alcohol fraction in the water-alcohol mixture. Meanwhile, the agitation caused the breakage of crystals, resulting in the decrease of the crystal size. Therefore, the crystal size in the crystallization was predominantly determined by the competition between the crystal aggregation and breakage.

• Journal of Biomedical Engineering Research
• /
• v.20 no.5
• /
• pp.609-616
• /
• 1999

심폐바이패스시 발생할 수 있는 튜브 마모 및 파쇄는 롤러펌프의 반복되는 압박에 의해 롤러펌프에 장착된 튜브 내벽에 균열이 생기고 이로 인해 미세한 비생물적 조각들이 혈액중으로 떨어져 나가는 현상을 말하는데, 임상적으로 치명적인 색전증을 초래할 수 있다. 그러나 아직 롤러펌프 튜브로 사용되는 PVC 및 실리콘 튜브 중 어느 쪽이 마모 및 파쇄 관점에서 더 우수한지는 체계적으로 밝혀지지 않고 있다. 이에 본 연구는 두 종류의 튜브를각각 일정 기간 롤러펌프에 장착하여 작동시킨 뒤 튜브내외면을 육안 및 주사형 전자현미경으로 관찰하였다. 즉 PVC 및 실리콘 튜브 (내경 1/2 인치의)들을 미리 정해진 폐쇄도 조절에 의해 폐쇄 회로 심폐비이패스 롤러펌프 헤드에 장착시키고 4.500ml/min에서 각각 4차례씩 1,2,4,6 시간 작동시켰다. 파쇄에 의한 색전 관찰 실험에서는 회로 중간에 동맥여과기를 설치하고 각각 6,9시간 씩 롤러펌프를 작동시켰다. 실험 후 튜브 및 여과기들을 수거한 후 육안 및 주사형 전자현미경 분석을 시행하였다. 실험후 튜브 및 여과기들을 수거한 후 육안 및 주사형 전자현미경을 분석을 시행하였다. 튜브 외부의 육안 관찰 결과 일반적으로 실라스틱 튜브에서의 외부 마모가 PVC 튜브에 비해 현저하였다. 주사형 전자현미경 관찰에서 PVC 튜브에서의 홈은 좁으면서 경계선이 뚜렷한 특징을 보였고 3시간 이상 롤러와 접촉한 튜브들에게서는 깊은 균열이 간헐적으로 관찰되었다. 반면, 실라스틱에서의 홈은 좁으면서도 경계선이 뚜렷한 특징을 보였고 3시간 이상 롤러와 접촉한 튜브들에게서는 깊은 균열이 간헐적으로 관찰되었다.반면 실라스틱에서의 튜브들에서는 홈이 상대적으로 넓고 경계가 덜 명확했으며, 특징적으로 V 자 모양의 융기부들이 간헐적으로 관찰되었다. 실라스틱 및 PVC 튜브 모두에서 50u 전후의 Craters 가 간헐적으로 관찰되었다. 여과기의 여과망에 대한 주사형 전자현미경 분석 결과 실라스틱과 PVC 튜브 실험군 모두에서 색전입자로 의심되는조각들이 발견되었으나 두군간 정량적 비교는 어려웠다. 결론적으로 롤러펌프에 의한 튜브 마모 및 파쇄현상은 실리콘 및 PVC 튜브의 재질에 따라 그 양상에는 차이가 있으나 임상적인 측면에서는 어느 쪽도 상대적인 우수성이 입증되지 못하였다.

• Resources Recycling
• /
• v.23 no.6
• /
• pp.30-39
• /
• 2014

The trajectories of PCB(Printed Circuit Board) particles in the corona discharge electrostatic separation was simulated. The PCB particles are prepared by crushing bare board, which disassembled from electronic components, consist mostly of copper and FR-4(Flame Retardant Level-4) Firstly, a model was established for calculating of detachment points of PCB particles from the rotating electrode in separator. The model of detachment points was derived from equilibrium of force such as gravity force, centrifugal force, electrostatic force. The trajectories of particles after detachment was calculated by acceleration derived from time-integrating method of motion equation. In this simulation, particle size, supplied voltage, rotation speed of rotating roll electrode and angle of induction electrode were adopted as variables. While the trajectories of FR-4 particles were affected by all variables, rotation speed of rotating roll electrode was dominant variables affecting trajectories of copper particles.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.9
• /
• pp.815-820
• /
• 2016

An elastic polymer (e.g., PDMS) blended with EFG particles is a promising conductive composite for fabricating soft sensors that can detect an object's deformation up to or more than 50%. Here, we develop large-strain, sprayable soft sensors using a mixture of PDMS and EFG particles, which are used as a host elastomer and electrically conductive particles, respectively. A solution for a conductive composite mixture is prepared by the microwave-assisted graphite exfoliation, followed by ultrasonication-induced fragmentation of the exfoliated graphite and ultrasonic blending of PDMS and EFG. Using the prepared solutions for composite and pure PDMS, 1-, 2-, and 3-axis soft sensors are fabricated by airbrush stencil technique where composite mixture and pure PDMS are materials for sensing and insulating layers, respectively. We characterize the soft strain sensors after investigating the effect of PDMS/EFG wt% on mechanical compliance and electrical conductance of the conductive composite.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.10
• /
• pp.1028-1033
• /
• 2008

Sequential quick crushing and alkali hydrolysis(SeCAH), as a pretreatment for foodwaste, incorporating mechanical crushing and alkali hydrolysis was proposed and investigated in this study. Focuses were placed on the improvement of biodegradability of foodwaste and the estimation of potential inhibitors for anaerobic digestion. The solubility of the pretreated foodwaste by SeCAH was increased 2.5 times rather than mechanical crushing. Considering solubility improvement and energy consumption, 2,000 rpm of crushing strength and 5$\sim$10 sec of crushing time are recommended. After SeCAH, the fraction of large organic particles(>2.36 mm) of foodwaste was sharply decreased from 88.0% to 29.0%, otherwise the fraction of small particles(<75 $\mu$m) was greatly increased from 10.5% to 40.7%. Ammouinum, potassium and sulfate were estimated as potential inhibitors for anaerobic digestion and their concentrations in pig slurry were 3331.3 mg/L, 4256.5 mg/L and 1017.5 mg/L, respectively.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.25 no.2
• /
• pp.141-155
• /
• 2023

Monitoring technology based on electrical resistivity is widely used for non-destructive data collection and health analysis of underground structures and tunnels. Vulnerable sections such as fault zone generates many problems during construction of the tunnel. These problems cause displacement and stress changes of the ground. Therefore, it is necessary to predict the state of the fault zone section to ensure the mechanical stability of the underground structure. Monitoring the size of joints and the porosity of the fillings is essential for rocks. Previous studies have not considered the variety of fillings in rock joints. In this study, electrical resistivity tests were conducted according to the particle mixing state of the sandy fillings. When the size of fillings is decreased at the constant porosity, the electrical resistivity tends to increase. The results of this study are expected to be useful as basic electrical resistivity data for predicting the ground conditions and evaluation of the ground behavior that is containing sandy fillings in the rock joint for tunnels.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.1391-1398
• /
• 2009

The vibrating table method is widely used to estimate the minimum void ratio $e_{min}$. The existing method recommended in ASTM and KS F, however, can not consider the particle crushing during the vibrating table test. In this study, the particle cursing phenomenon was investigated by comparing vibrating table test with pluviation method using artificial sand (K-7). Vibrating table test for the artificial sand was confirmed which can crush of particle during the test. This study demonstrates that vibrating table test is an ineffective method to produce the more reliable $e_{min}$ of artificial sand.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.3 no.3
• /
• pp.201-211
• /
• 2005

In this study, conventional head-end processes of spent TRISO fuel have been reviewed to develope more effective treatment methods. The main concerns in the TRISO treatment are to effectively separate the carbon and SiC contained in the TRISO particles. The crush-burn scheme which was considered in the early stages of the development has been replaced by the crush-leach process because of $^{14}C$ problems as a second waste being generated during the process. However, there are still many obstacles to overcome in the reported processes. Hence, innovative thermomechanical concepts and a molten salt electrochemical approach to breach the coating layers of the TRISO particle with a minimized amount of second waste are proposed in this paper and their principles are described in detail.

• Journal of the Korean GEO-environmental Society
• /
• v.3 no.1
• /
• pp.67-77
• /
• 2002

Volume change of the dredged soils is composed of the volume loss of soil particle flowing over an outflow weir with water and settlement due to both the self-weight consolidation in reclaimed layer and the desiccation at the surface of reclaimed layer. In order to estimate the amount of soil particles flowing over an outflow weir with water, the evaluation procedure of loss ratio of the dredged soils is proposed in the present study based on the Marsal's modified breakage theory and the results of hydrometer analyses. To verify a validity of the proposed procedure, evaluated loss ratio is compared with results from the other existing methods. The model test results and those of field test were compared and analyzed. Also, the variation of soil loss ratio was examined through the model test in the lab.

• Resources Recycling
• /
• v.28 no.2
• /
• pp.23-30
• /
• 2019

An color sorting technique was introduced to recycle End-of-life automobile shredded bumpers. The color sorting is a innovate method of separating the differences in the color of materials which are difficult to separate in gravity and size classification by using a camera and an image process technique. Experiments were planned and optimal conditions were derived by applying BBD (Box-Behnken Design) in the reaction surface method. The effects of color sensitivity, feed rate and sample size were analyzed, and a second-order reaction model was obtained based on the analysis of regression and statistical methods and $R^2$ and p-value were 99.56% and < 0.001. Optimum recovery was 94.1% under the conditions of color sensitivity, feed rate and particle size of 32%, 200 kg/h, and 33 mm respectively. The recovery of actual experiment was 93.8%. The experimental data agreed well with the predicted value and confirmed that the model was appropriate.