• Proceedings of the KAIS Fall Conference
• /
• 2001.05a
• /
• pp.108-112
• /
• 2001

본 논문에서는 전산유체해석 기법을 이용하여 저소음ㆍ고효율 공조기의 입구형상에 대한 유동해석을 하였다. 공조기 입구형상을 결정하는 여러 설계변수가 입구와 출구의 유동조건과 유로의 압력손실에 미치는 영향을 평가하였다. 이를 바탕으로 입구와 출구유동의 균일성과 압력손실의 최소화를 만족하는 최적의 설계 변수를 결정하여 공조기의 최적설계를 달성하였다.

• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.2
• /
• pp.9-21
• /
• 1999

The waterjet is very widely used today in propulsion system of high speed vessel but manufacturer is limited because of an efficiency and a difficulty of a manufacture on the inlet configuration of the waterjet. The importancy in designing the inlet configuration of the waterjet lies on the minimization of the cavitation which is largely affecting the efficiency. In this paper, the configuration analysis is carried out to find a optimum shape which is minimizing the cavitation using a two dimensional potential-based panel method with an inlet configuration of a flush type. Also, it is developed a direct design method finding an inlet configuration by a given pressure distributions. The numerically obtained optimum shape using this configuration analysis method show a good agreement compared to the Kashiwadani's results. It is carried out a direct design method over a lip and a ramp of an inlet configuration wish pressure distributions obtained a result of the configuration analysis and the results show a good agreement compared to original configuration.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.5
• /
• pp.479-486
• /
• 2011

In image-based CFD modeling of carotid bifurcation hemodynamics, it is often not possible (or at least not convenient) to impose measured velocity profiles at the common carotid artery inlet. Instead, fully-developed velocity profiles are usually imposed based on measured flow rates. However, some studies reported a pronounced influence of inflow boundary conditions that were based on actual velocity profiles measured by magnetic resonance imaging which showing the unusual presence of a high velocity band in the middle of the vessel during early diastole inconsistent with a Dean-type velocity profile. We demonstrated that those velocity profiles were induced by the presence of modest secondary curvature of the inlet and set about to test whether such more "realistic" velocity profiles might indeed have a more pronounced influence on the carotid bifurcation hemodynamics. We found that inlet boundary condition with axisymmetric fully-developed velocity profile(Womersley flow) is reasonable as long as sufficient CCA inlet length of realistic geometry is applied.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.254-254
• /
• 2004

미세 방전 가공은 전도성 재료에 미세 구멍을 가공할 때 주로 적용되는 방법이다. 그러나 미세 방전가공을 이용하여 구멍을 가공할 때 직경이 일정한 공구를 사용하더라도 입구와 출구의 직경에는 차이가 생긴다. 구멍의 벽면과 공구사이에는 2차 방전이 발생하고 상대적으로 2차 방전의 영향을 많이 받는 입구가 출구보다 직경이 커지게 된다. 이 때문에 미세 구멍의 단면 형상은 깊이 방향으로 테이퍼가 생기게 되며, 이로 인해 진직 구멍을 가공할 수 없게 된다. 따라서 이 논문에서는 이러한 테이퍼 형상을 제거하여 진직 구멍을 가공하는 방법에 관해 연구하였다.(중략)

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.3
• /
• pp.271-277
• /
• 2014

Internal structures, especially those located in the upstream of a reactor core, may have a significant influence on the core inlet flow rate distribution depending on both their shapes and the relative distance between the internal structures and the core inlet. In this study, to examine the effect of the reactor internal structure geometry treatment method on the prediction accuracy for the scale-down APR+ flow distribution, simulations with real geometry modeling were conducted using ANSYS CFX R.14, a commercial computational fluid dynamics software, and the predicted results were compared with those of the porous medium assumption. It was concluded that the core inlet flow distribution could be predicted more accurately by considering the real geometry of the internal structures located in the upstream of the core inlet. Therefore, if sufficient computational resources are available, an exact representation of these internal structures, for example, lower support structure bottom plate and ICI nozzle support plate, is needed for the accurate simulation of the reactor internal flow.

• Journal of the Korean Institute of Gas
• /
• v.16 no.1
• /
• pp.1-7
• /
• 2012

The present study has been carried out to analyze the flow characteristics in the inlet expasion duct of a heat recovery steam generator by using numerical flow analysis. The inlet of HRSG corresponds the outlet of gas turbine exit and the flow after gas turbine has strong swirl flow and turbulence. The inlet flow condition of HRSG should be included the exit flow characteristics of gas turbine. The present numerical analysis adopted the flow analysis result of gas turbine exit flow as a inlet flow condition of HRSG analysis. Because the flow characteristics in the inlet duct of the tube bank is strongly related to the performance of a HRSG, it is most important for the optimal design of HGSG to understanding the flow phenomena in the inlet duct of HRSG. From the present study, the position of breakpoint in the inlet expansion duct should be lower than the reference breakpoint position for the optimal flow uniformity before the tube bank.

• Proceedings of the KAIS Fall Conference
• /
• 2012.05b
• /
• pp.743-747
• /
• 2012

본 논문에서는 HEV배터리의 Lay-Out 변화의 형상 및 개수와 위치 변화에 따른 냉각 특성에 관하여 연구 하였다. Lay-Out의 형상과 위치 변화에 따른 온도, 압력, 속도를 분석 하였고, 1가지 기본 형상을 기준으로 2가지 형상 변화를 통하여 온도, 압력, 속도를 비교해 보았다. 사각형의 입, 출구의 위치의 개수 추가 했을 때 온도강하가 일어나는 것을 알 수 있었으며, 입구 형상을 원으로 하고 위치변화와 개수를 변화 하였을 때 사각형의 입구 보다 더 좋은 온도강하의 결과를 도출해 낼 수 있었다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.2
• /
• pp.109-117
• /
• 2015

Aircraft needs an inlet duct to supply the airflow to engine face. A fighter aircraft that requires low radar observability has to hide the engine face in the fuselage to reduce the Radar Cross Section(RCS). Therefore, the flow path of the inlet duct is changed into S-shape. The performance of the aircraft engine is known to be influenced by the shape and the centerline curvature of the S-Duct. In this study, CFD analysis of the RAE M 2129 S-Duct has been performed to investigate the influence of aspect ratio of inlet geometry. The performance of the S-Duct is evaluated in terms of the distortion coefficient. To simulate the flow under adverse pressure gradient better, $k-{\omega}SST$ turbulence model is employed. The computational results are validated with the ARA experimental data. The secondary flow and the flow separation are observed for all computational cases, while the semi-circular geometry has been found to produce the best results.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.5
• /
• pp.107-114
• /
• 2019

In many military aircraft, s-shaped diffusers are used to prevent the fan blades of the turbofan engine from being exposed to the outside. The inlet configurations of the air intakes for military aircraft vary, such as the rectangular intake of the F-22, the crescent-like intake of the F-16, elliptical intake of the MQ-25. In this study, the aerodynamic performance of s-shaped diffusers with various inlet configurations was evaluated using numerical analysis. In addition, the configuration of the middle section of an s-shape duct was changed to the crescent shape, and the effects on its aerodynamic performance were investigated. As a result, there was a slight difference in total pressure recovery according to various inlet configurations with ellipse-shaped middle sections. Also, the total pressure distortion was the lowest in the rectangular inlet shape. When the configuration of the middle section was changed from an ellipse to a crescent shape, the total pressure recovery remained at a high level, except for the ellipse-shaped inlet configuration. In terms of total pressure distortion, the duct with the crescent-shaped middle section showed a significantly more uniform pressure distribution than that with the ellipse-shaped middle section.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.629-634
• /
• 2011

A prestudy on expendable turbine engine for high-speed vehicle was conducted. The two possible mission profiles were established to decide the engine requirements and Design Point, and Design Point analysis was performed with the values of design parameter which were obtained from similar class engines and technical references. The results showed that Specific Net Thrust is 2599.4 ft/s and Specific Fuel Consumption is 1.483 lb/($lb^*h$) at the flight condition of Sea Level, Mach 1.2. It was also found through the performance analysis on the two possible mission profiles that major design parameters for determining Net Thrust were Turbine Inlet Temperature for low supersonic flight speed and Compressor Exit Temperature for high supersonic flight speed. In addition, simple turbojet engine with axial compressor, straight annular combustor, axial turbine and fixed throat area converge-diverge exhaust nozzle was proposed as the configuration of simple low cost light engine.