• Korean journal of applied entomology
• /
• v.42 no.4
• /
• pp.315-321
• /
• 2003

Larval entrance and adult emergence holes of Japanese pine sawyer (Monochamus alternatus), primary vector of pinewood nematode (Bursaphelenchus xylophilus), were measured in dead pine logs from 1999 to 2002. Their distributions within pine log were also analyzed. More numbers of entrance and emergence holes were distributed on crown than trunk part as 56.2 and 27.7 holes/m$^2$, respectively Higher proportions of entrance (27.5％) and emergence holes (22.4%) were distributed on the log with 8 to 10 cm diameter; the larger or the smaller logs had fewer holes. Surface area of entrance hole was 65.8 $\textrm{mm}^2$ and diameter of emergence holes was 7.0 mm in average. Average depth of pupal chamber was 24.8 mm from surface to the bottom of the chamber, and its volume ranged from 200 to 2.000 ㎣ Average distance between entrance and emergence holes on bark surface was 3.3 cm. Gallery length from the beginning of entrance hole to the end of emergence hole was 46.2 mm.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.28 no.4
• /
• pp.49-63
• /
• 2010

This study focused on the method of separation - space organization- as one of the architectural methods that is considered by the view point of its location and arrangement of 'Byoul-seo' private garden pavilion in Honam province. As a result, the followings are conclusions; By this study, they can be found in the concept of '居敬窮理', '格物致知'. It is presumed that nature union is archived through the 'yan-sang(玩賞)' which is ultimate state of knowledge that is based on the premises of opened significance in emancipation from narrow view point in the past and cognition of value. Therefore, it is needed to know the unworldly point of space perception about the pavilion territory, furthermore to have conceptual method to distinct pavilion from the world. there are two methods in the distinct concept in this pavilion research: unworldly separation and meditative separation. It is concluded that the specific consideration of the method of separation that is applied in the Byoul-seo pavilion. And it is accomplished by the contemplation of separation method in approach and entrance of direct influence area. they could be 1) cross the hill, 2) cross over a brook, 3) lifted up in the mount, 4) penetrate the forest, and 5) narrow entrance, which could be part of location.

• Journal of Life Science
• /
• v.30 no.1
• /
• pp.32-39
• /
• 2020

Rhododendron mucronulatum, native to Korea, Mongolia, Russia and parts of northern China, is known not only for its medicinal properties but also as a tourist attraction. One of the most famous tourist destinations with R. mucronulatum is in Biseul Mountain County Park, Daegu, Korea. To investigate the relationship between R. mucronulatum and microbiome communities in the surrounding soil, three sites within the park were chosen for sampling in February and August. The soil samples were then passed through a pyrosequencing process for analysis of the bacterial communities, and a total of 404,899 sequencing reads were obtained. Between 2,349 and 4,736 operational taxonomic units (OTUs) were observed across the three sampling zones and two seasons; samples from the park entrance showed a higher number of OTUs than the other two sites, and samples from August had more OTUs than those from February. The sample from the second observation site displayed the fewest OTUs, particularly in February. According to Chao1 and Shannon indices, samples from the park entrance in August demonstrated the highest degree of species richness and diversity. Studying the bacterial communities across the six samples identified the common population as comprising 287 genera, 45 of which are only present in Biseul Mountain County Park and are expected to participate in the colonization of R. mucronulatum.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.13 no.6
• /
• pp.77-87
• /
• 2014

It has reported that a median bus-stop island on an exclusive median bus lane (EMBL) has shortened a crossing distance unit, encouraged a pedestrian's illegal crossing, and increased the number of accidents in the area. This study presents (1) the analysis of inappropriate pedestrian crossing patterns collected on exclusive median bus corridors and (2) the estimated performance of safety barriers restraining the occurrence of those. Total 19,649 pedestrian crossing data collected at the 'Sookmyung-university' median bus-stop, and the inappropriate pedestrian crossing patterns among those were grouped in terms of time and space violations. Physical safety barriers restraining illegal pedestrian crossings were considered as an alternative, and its performance in safety was quantified through microscopic simulation with conflict analyses by using surrogate safety assessment model. The findings suggest the number of conflicts reduced be 24.9 percentages compared to the one of the present condition when the physical safety barriers are placed at each of the eight ends of the EMBL pedestrian crossing.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.58-58
• /
• 2017

점적 호스의 원통형 미로 구조물내의 유동특성을 분석하기 위해 금속판에 동일한 구조의 미로가 가공된 시험부를 활용하여 압력과 유량의 변화에 대한 실험을 CFD 해석하였다. 해석은 미로의 길이에 따른 유량 특성을 정밀하게 분석하기 위해 전체 미로에 구간별 총 8개의 배출구를 배치하고 밸브 조절을 통해 구간별 압력에 따른 유량을 측정함으로서 실험에 의한 압력과 유량의 관계를 검증하고 새로운 경질 미로를 설계하는데 응용하고자 한다. 경질 미로의 이론적인 해석에서 정밀도가 실험을 대신할 가능성이 있는지에 관심을 두었다. 점적관수의 경질 미로는 디자인을 달리함으로써 성능이 높고 미세한 스케일이 침착되지 않는 고성능의 점적관수 장치의 개발이 가능할 것으로 판단하였다. 미로 입구의 공급 유체 압력(Gauge pressure)을 0.5, 1.5, 2.5, 3.0 bar로 나누어 공급하였으며, 8개의 구간별 유출되는 유량은 전자저울에서 측정하였다. 향후 최적 미로의 새로운 설계를 위해 미로구조 전체를 CFD 해석하였고 그 결과를 실험치와 비교 분석하였다. 또한 경질 미로내 각 구간별 세부적인 유동구조를 분석하였고 해석결과와 실험결과를 통해 향후 새로운 경질 구조의 개발이 가능 할 것으로 판단되었다. 경질 미로의 입구압력에 따른 미로의 길이 #1과 #2에 대한 CFD 분석에서는 전체적으로 경질 미로에 압력이 증가할수록 미로의 유체 속도가 증가됨을 알 수 있었으며 이것은 #2에서도 거의 같은 양상을 나타내었다. 미로 통로에서는 와류로 인한 이물질의 멈춤 현상이 발생하지 않을 만큼 흐름이 원활함을 알 수 있었다. 미로의 길이 #3과 #4에 대한 CFD 분석과 미로의 길이 #5와 #6에 대한 CFD 분석에서는 압력이 증가하고 미로의 길이가 길어질수록 속도에도 영향을 미치고 있는 것으로 나타났으며 미로와 미로 사이의 넒은 통로에서는 유속이 크게 떨어지고 있음을 알 수 있었다. 따라서 이 부분에는 유체속의 이물질이 침착할 수 있는 가능성이 있으며 통로가 좁은 곳에서는 유속이 증가되는 것으로 나타났다. #7과 #8은 미로의 상하단으로 유출되는 부분의 차이이므로 실질적으로 해석의 결과는 차이가 없었다. 경질 미로에 대한 압력에 따른 미로의 길이별 유출량은 지수적인 반비례 현상을 나타내어 앞서 실험한 연구의 결과와 1~2% 오차 범위에서 잘 일치하였다. 따라서 점적 호스의 경질 미로에 대한 설계는 이론적인 해석을 통하여 새로운 디자인이 가능할 것으로 판단되었다. 경질 미로의 미로의 길이에 따른 CFD 분석의 결과는 실험적인 유출량의 값과 거의 일치하였다. 미로와 미로 사이의 넒은 통로에서는 유속이 크게 떨어져 이물질들이 침착될 가능성이 있었으며 실질적으로 넓게 설계하는 것이 유리하지 않을 것으로 판단되었다. 경질 미로에 대한 압력에 따른 미로의 길이별 유출량은 지수적으로 반비례 하였으며 점적 호스의 경질 미로에 대한 새로운 설계는 이론적인 해석을 통하여 가능할 것으로 판단되었다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.12
• /
• pp.4721-4726
• /
• 2010

The performance characteristics of water-chilling heat pump using CO2 for the control of inverter frequency was investigated experimentally. An experimental apparatus is consisted of a compressor, a gas cooler, an expansion valve, an evaporator and a liquid receiver. All heat exchangers used in the test rig are counter flow type heat exchangers with concentric dual tubes, which are made of copper. The gas cooler and the evaporator consist of 6 and 4 straight sections respectively arranged in parallel, each has 2.4m length. The experimental results summarize as the following: for constant inlet temperature of evaporator and gas cooler, as mass flow rate, compression ratio and discharge pressure increases with the inverter frequency. And heating capacity and compressor work increases, but coefficient of performance(COP) decreases with the inverter frequency of compressor. As inlet temperature of secondary fluid in the evaporator increases from $15^{\circ}C$ to $25^{\circ}C$, compression ratio and compressor work decreases, but mass flow rate, heating capacity and COP increases with the inverter frequency of compressor. The above tendency is similar with performance variation with respect to the variation of inverter frequency in the conventional vapor compression refrigeration cycle.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2006.06b
• /
• pp.199-206
• /
• 2006

Today the harbor oscillation problems are the most significant factor to design harbors serving the very large ships. Large vessels moored in the elastic hawsers at the coastal harbors are often displaced due to the resonance between the long period waves and mooring system. The cargo handling may be interrupted and the hawsers may be broken, especially when the amplification becomes remarkable. The most significant harbor which is confronted with harbor oscillation problem in Korea is the Pohang New Port. Many cases of problems are being notified by the pilot association and local office of MOMAF. However, it is difficult to prevent the arrival of long waves causing oscillation within this harbor. Moreover, Government already started new port plan at the mouth of YoungIl Bay without treating problems occurred in the Pohang New Port. This study deals with the variation of harbor oscillation due to the construction of 4.1km breakwater at the bay mouth and new port plan. Numerical method used are fairly standard form from the extended mild slope equation. The obtained numerical results were compared with the field measurement from the previous study and this will bring a certain level of discussion and consideration of variation in the future port development.

• Clean Technology
• /
• v.29 no.4
• /
• pp.305-312
• /
• 2023

Due to the strengthening of environmental requirements, aging denitrification facilities need to improve their performance. The present study aims to suggest the possibility of improving performance using computational analysis techniques. This involved modifying both the geometric design and the operating conditions, including the flow path shape of the equipment such as the inlet guide vane and the curved diffusing part, and the flow control of the ammonia injection nozzle. The conditions presented in this study were compared with existing operating conditions in terms of the flow uniformity, the NH₃/NO molar ratio of the mixed gas flowing into the catalyst layer, and the total pressure drop of the facility. The flow field applied in the computational analysis ranged from the outlet of the economizer in the combustion furnace to the inlet of the air preheater, the full domain of the denitrification facility. The performances were derived by solving the flow fields using ANSYS-Fluent and the injection amount of ammonia was adjusted for each nozzle using Design Xplorer. Compared to the denitrification performances of the equipment currently in operation, the conditions proposed in this study showed an improvement in the flow uniformity and NH₃/NO composition ratio by 45.1% and 8.7%, respectively, but the total pressure drop increased by 1.24%.

• Journal of the Korean Arthroscopy Society
• /
• v.6 no.2
• /
• pp.195-199
• /
• 2002

This article is to report a new technique for reconstruction of the anteromedial and posterolateral bundles of anterior cruciate ligament by separate tensioning and fixation of the each bundle. Method : Tibial and femoral tunnels were made with conventional technique of anterior cruciate ligament reconstruction. Tibial tunnel was enlarged $5\~7$ mm in anterior-posterior direction to make oval it in cross section. When preparing the Achilles tendon allograft, bone plug portion was trimmed as the conventional technique. The tendinous portion was trimmed as two separate bundles by dividing the tendinous portion longitudinally, so the graft is shaped like 'Y'. The bone plug portion of allograft was inserted into the femoral tunnel and fixed with absorbable cross pins. Two ligamentous portionss of the distal part of the grafts were tensioned separately at the external orifice. Anteromedial bundle was fastened under maximum tension with the knee flexed 90 degrees by post-tie method. The posterolateral bundle was fixed by the same technique with the knee in full extension. Then, an absorbable interference screw was inserted between the two bundles upto the upper end of the tibial tunnel, to get more initial rigidity of the reconstructed graft as well as to locate the two bundles in more anatomic position.

• Conservation Science in Museum
• /
• v.22
• /
• pp.41-52
• /
• 2019

Inner walls of the stone chamber of West Ancient Tomb No. 1 and 2 in Neungsan-ri, Buyeo-gun have been inspected for possible trace of murals. Tomb No.1 has a rough surface finish of the stone wall and no traces of murals was observed in any part of the stone walls except the ceiling part of the main chamber. On the ceiling surface, there is black colored area, which showed same visual characteristics for both the surface and interior upon slight scratch of the surface, suggesting that it may not be a painted layer. In addition, this black material is not artificial stuff like black ink but is confirmed as biotite from X-ray diffraction analysis that is one of the constituents of the stone wall. In case of tomb No. 2, white material, that is confirmed as lime(calcite, CaCO3) by X-ray diffraction analysis, was observed on the wall surface of the east, west and north, suggesting possible existence of murals. The lime layers, however, are located mostly on the entrance of east wall of main chamber and the place of passage whereas they are observed only in lower parts on the other walls. It may have been formed by the inflow of soil and lime from the outside as the form of the lime layer in the east wall corresponds to the traces of soil and lime deposited from the thief pit. Furthermore, the filling material found in the gap between the stone slabs of the four directions and the ceiling was confirmed as clay soil, which is different material from the lime present on the stone wall surface. If the lime layer had been artificially constructed for the purpose of creating murals, it would have been more reasonable to use lime as well in the gap between the stone slabs of the four directions and ceiling. In this regard, we conclude that there are no murals in the Tomb No. 2 in the Neungsan-ri.