• Transactions of the Korean hydrogen and new energy society
• /
• v.25 no.2
• /
• pp.191-199
• /
• 2014

Effects of design variables on the performance of a double-inlet centrifugal blower have been analyzed based on the three-dimensional flow analysis. Two design variables, blade inlet and outlet angles, are introduced to enhance a blower performance. General analysis code, ANSYS-CFX13, is employed to analyze internal flow and a blower performance. SST turbulence model is employed to estimate the eddy viscosity. Throughout the shape optimization of an impeller at the design flow condition, the blower efficiency and pressure are successfully increased by 4.7 and 1.02 percent compared to reference one. It is noted that separated flow observed near cut-off region can be reduced by optimal design of blade angles, which results in stable flow pattern in the blade passage and increase of a blower performance. The stable flow at the impeller also makes good effects at the outlet of a volute casing.

• The KSFM Journal of Fluid Machinery
• /
• v.8 no.2 s.29
• /
• pp.31-38
• /
• 2005

A low NPSH and high pressure fuel pump has been designed for a turbopump system. The fuel pump has an axial inducer and a centrifugal impeller. A meanline method has been established for the preliminary design and performance prediction of pumps at design or off-design points. KeRC(Kelyish Research Center) carried out a model testing of the fuel pump with water as a working fluid at the reduced speed. Predicted performances by the method are shown to be in good agreement with experimental results for cavitating and non-cavitating conditions. The established meanline method can be used for the performance prediction and preliminary design of high speed pumps which have a inducer, impeller and volute. In the current study, the three dimensional viscous flow in the fuel pump was investigated through numerical computation. A modified design of the fuel pump was generated to improve pump performance by utilizing CFD results. The modified fuel pump was experimentally tested by ROTEM and KARI(Korea Aerospace Research Institute). The measured non-cavitating and cavitating performance showed a good agreement with designed performance.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.2
• /
• pp.136-148
• /
• 1997

The present study has been carried out to develop a computational procedure for the analysis of the off-design performance in centrifugal compressors with vaneless diffusers by integrating empirical loss models and analytical equations. Losses in centrifugal compressors stem from a number of sources and their exact calculation is not yet possible. This study investigates several modeling schemes and shows that a fairly good prediction can be achieved by a proper selection of the most important flow parameters resulting form a meanline one-dimensional analysis. The performance maps for compressors are calculated and compared with measured performance maps. The off-design performance characteristics in terms of the pressure ratio vs. mass flow produced have generally correct forms. However, no universal means have been found to predict accurately the onset of surge. The prediction method developed through this study can serve as a tool to ensure good matching between parts and it can assist the understanding of the operational characteristics of general purpose centrifugal compressors.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.341-346
• /
• 2004

A low NPSH and high pressure fuel pump has been designed for a turbopump system. The fuel pump has an axial inducer and a centrifugal impeller. A meanline method has been established for the preliminary design and performance prediction of pumps at design or off-design points. KeRC carried out a model testing of the fuel pump with water as a working fluid at the reduced speed. Predicted performances by the method are shown to be in good agreement with experimental results for cavitating and non-cavitating conditions. The established meanline method can be used for the performance prediction and preliminary design of high speed pumps which have a inducer, impeller and volute. In the current study, the three dimensional viscous flow in the fuel pump was investigated through numerical computation. A modified design of the fuel pun was generated to improve pump performance by utilizing CFD results. The modified fuel pump was experimentally tested by ROTEM and KARI. The measured non-cavitating and cavitating performance showed a good agreement with designed performance.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.435-436
• /
• 2009

In the effort on cost reduction in marine equipment company, the medium sized impeller blade ($500mm{\times}200mm{\times}20mm$) of an axial flow pan was manufactured by the high pressure die casting, with which was replaced the gravity die casting. High pressure die casting is a practical alternative because of some advantages such as excellent accuracy and smooth cast surface as well as cost reduction if a certain amount of porosity in the parts can be minimized. In order to reduce the porosity in the center of the neck which is thickest region of the impeller blade, the several gate designs were proposed in this work. The flow simulations for each gate design were performed and then the optimal design was determined by considering the air pressure distribution in neck section. Finally, the size of porosity in the neck of the die cast impeller blade for optimal design was less than 1mm, which satisfied the requirement.

• The KSFM Journal of Fluid Machinery
• /
• v.17 no.1
• /
• pp.28-34
• /
• 2014

This paper presents the performance enhancement of a double-inlet centrifugal blower by the shape optimization of an impeller. Two design variables, a number of blade and a length of chord, are introduced, and analyzed by a response surface method. Three-dimensional compressible Navier-Stokes equations are used to analyze the blower performance and the internal flow of the blower. Throughout the numerical simulation of the blower, blower efficiency can be increased by reducing separation flow generating from the blade leading edge of a blade pressure surface. It is noted that recirculation flow observed inside the blade passage induces low velocity region, thus increases pressure loss. Efficiency and pressure of the optimum blower are successfully increased up to 3% and 3.9% compared to those of reference blower at the design flow condition, respectively. Detailed flow field inside the blower is also analyzed and compared.

• The KSFM Journal of Fluid Machinery
• /
• v.13 no.1
• /
• pp.23-28
• /
• 2010

A draft tube which has impeller to elevate bottom water and spread it over surface of lake water, induces convective circulation of lake water, a Long-Distance Circulation (LDC). Circulation of lake water make stratified water mixed and enhance DO (Dissolved Oxygen) of bottom water. Circulation rate of water is determined by draft rate of the tube, which is dependent on design parameters of the draft tube system, i. e. dimension of impeller and diffuser, inclined angle of impeller, impeller shape, and rotational speed. In this study, change in draft rate and power consumption of circulation equipment was investigated numerically with changing impeller dimension, angle and rotational speed. It was found that flowrate of draft water was increased as the dimensions of draft tube and impeller, and rotational speed and inclined angle of impeller increased. The power consumption was also elevated with increasing parameter values, and final selection of parameter values was made to satisfy target flowrates and power consumption.

• The KSFM Journal of Fluid Machinery
• /
• v.18 no.1
• /
• pp.20-28
• /
• 2015

The pump-turbine impeller is the key component of pumped storage power plant. Current design methods of pump-turbine impeller are private and protected from public viewing. Generally, the design proceeds in two steps: the initial hydraulic design and optimization design to achieve a balanced performance between pump mode and turbine mode. In this study, the 3D inverse design method is used for the initial hydraulic impeller design. However, due to the special demand of high performance in both pump and reverse mode, the design method is insufficient. This study is carried out by modifying the geometrical parameters of the blade which have great influence and need special consideration in obtaining the high performance on the both modes, such as blade shape type at low pressure side (inlet of pump mode, outlet of turbine mode) and the blade lean at blade high pressure side (outlet of pump mode, inlet of turbine mode). The influence of the geometrical parameters on the performance characteristic is evaluated by CFD analysis which presents the efficiency and internal flow results. After these investigations of the geometrical parameters, the criteria of designing pump-turbine impeller blade low and high sides shape is achieved.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2019.10a
• /
• pp.645-648
• /
• 2019

본 논문은 벽면 이동 로봇의 진공흡착 방법 개선에 관한 연구로서, 로봇의 무게에 따른 중력을 견딜고 벽면에 흡착 및 이동할 수 있는 동작 환경을 시뮬레이션을 통해 효율적으로 설계한다. 이동로봇에 미치는 다양한 힘의 조건들을 판단하며 특히 벽의 수직방향으로 미는 힘과 챔버 내의 저압조건 등과의 상관관계를 고려하여 흡착 능력을 개선하기 위한 방법을 제시하고 실험을 통해 성능을 검증하였다 또 한 본 연구에서는 압력센서를 이용하여 실시간으로 압력을 체크 하면서 모터의 속도인 PWM의 한계치를 설정하여 압력에 따라 필요한 임펠러의 속도를 PWM으로 적절히 조절해줌으로써 흡착에 관련된 제어 능력을 개선하고 흡착에 필요한 일정 압력 값에 도달하지 못할 때 작업이 종료되는 기술을 개발하였다.

• Transactions of the Korean hydrogen and new energy society
• /
• v.32 no.4
• /
• pp.277-284
• /
• 2021

This paper deals with multi-objective optimization using response surface method to improve the hydraulic performances of a 2 vane pump for wastewater treatment. For analyzing the internal flow field in the pump, steady Reynolds-averaged Navier-Stokes equations were solved with the shear stress transport turbulence model as a turbulence closure model. The impeller and volute variables were defined in the shape of the 2 vane pump. The objective functions were set to satisfy the total head at the design flow rate as well as to improve the efficiency. The hydraulic performance of the optimally designed shape was verified by numerical analysis results.