• The korean journal of orthodontics
• /
• v.20 no.2
• /
• pp.363-379
• /
• 1990

The purpose of this study was to evaluate the effects of the mandibular retractive force on the mandibular condyle of growing dog. The experimental animals were six mongrel dogs of two-month old. Their deciduous dentition were completed. Two of them was used as control group, and experimental group was composed of remaining four. Head band and chin cup were made of cotton tape, and hooks are fabricated on the chin cup and had band for closed coil. Mandibular retractive force was 100g/side and chin cap appliance was used for 14 hours/day during night. Experimental group were sacrificed at 2, 4, 6, 8 weeks from beginning of the experiment. Right TMJ was prepared for histologic study and left TMJ was examined grossly for disc, fossa, and condyle. The conclusions are: 1. Two-month old control animal showed active cartilaginous growth on the mandibular condyle, therefore showed thick proliferative and hypertrophic zones. Remodeling process in the condyle head was observed in which there were bone resorption on the anterior surface and bone apposition on the posterior surface. 2. Four-month old control animal showed marked reduction of hypertrophic zone but the condylar bone remodeling was more pronounced. 3. In experimental group, there are marked reduction of hypertrophic zone at 4 weeks from beginning of experiment, and hypertrophic zone disappeared at posterior-superior portion of condyle in 6-week experimental animal. 8 week experimental animal showed slight recovery of hypertrophic zone. 4. In experimental group, bone deposition was increased at anterior surface of condyle, and bone resorption was increased at posterior surface of condyle. 5. In control group, the glenoid fossa and surrounding bone showed mainly bone apposition. But experimental group showed bone resorption at anterior surface of articular eminence and increased bone apposition at posterior surface of postglenoid spine. 6. No marked traumatic change was seen but 4 weeks and 8 weeks experimental animal showed flattening of posterior surperior condylar surface. Bone marrow of condyle showed minute focal bleeding in 2 weeks and 4 weeks experimental animal, and congestion and depression of hematopoietic bone marrow during all experimental period.

• The korean journal of orthodontics
• /
• v.26 no.5 s.58
• /
• pp.591-599
• /
• 1996

This study was undertaken to investigate the cytotoxicity of orthodontic wires after doing various treatments to the wires. 018x025 inch Stainless steel(A) and Co-Cr(B) wires were used and each of them were divided into 4 groups. A-1 and B-1 groups were as received state, and A-2 and B-2 groups were heat treated. A-3 and B-3 groups were electropolished after heat treatment, and A-4 and B-4 groups were soldered with Ag-solder. Each group had 3 wires and these were sterilized with Ethylene Oxide gas. We used human gingival fibroblast cell culture and agar overlay technique to investigate the cytotoxicity of each group of wires. The cytotoxicity of wire was assessed using reaction index (zone index/lysis index). The findings of this study were as follows. 1. Both of the stainless steel wire and Co-Cr wire showed no cytotoxicity in as received state. 2. Heat treatment or electropolishing of the wires had no effect on the cytotoxicity of the wires 3. Soldered stainless steel wires showed a little wider zone of discoloration than soldered Co-Cr wires, but the zone index and cytotoxicity(reaction index) was not different. 4. Soldered wires showed moderate cytotoxicity in both of the wires.

• The korean journal of orthodontics
• /
• v.36 no.6
• /
• pp.402-411
• /
• 2006

Objective: This study was carried out to evaluate the distribution and clinical features of patients with degenerative change of the mandibular condyle. Methods: Six thousand and seventy patients with TMD (temporomandibular cisorder) were selected for this study, who had complete initial clinical records and radiographs. Panorama and TMJ panorama radiographs were used to screen the degenerative change in the condyle, and the patients were divided into DJD (degenerative joint disease) and non-DJD groups. Results: The distribution. and clinical features of the two groups were compared. Out of the total number of patients, 31.7% were in the DJD group, and 68.3% were in the non-DJD group. The portion of females was larger in the DJD group (80.8%) than in the non-DJD group (67.5%), and the DJD group had high prevalence in the second and third decades. Lack of incisal contact, retrusive chin, facial asymmetry, and mouth opening limitation were the chief complaints of the patients who had positive relation to DJD. Conclusion: Patients with an orthodontic treatment history, CO-CR discrepancy and crepitation were at possible risk of having DJD.

• The korean journal of orthodontics
• /
• v.35 no.2 s.109
• /
• pp.137-147
• /
• 2005

The purpose of this study was to investigate the stress distribution in the periodontal tissue and the displacement of teeth when active torque was applied to the maxillary incisors by three-dimensional finite element analysis A three-dimensional finite element model consisted of the maxillary teeth and surrounding periodontal membrane, $.022{\times}.028$ Roth prescription bracket and stainless steel, NiTi and TMA rectangular ideal arch wires which were modeled by hexahedron elements. Applied active torques were 2, 5 and 10 degrees ThHe findings of this study showed that the reaction force acting or the bracket was the extrusion force on the mesial side of the incisors and canine and the intrusion force on the distal side of the incisors and canine. The amount of force and moment was greatest at the lateral incisor. When active anterior labial crown torque was applied. labial crown and distal tipping and Intrusion of the incisors took place. and lingual crown distal tipping and extrusion of the canine occured. An excessive force was concentrated on the lateral incisor, when the stainless steel wire was used NiTi or TMA wire is desirable for torque control.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2023.05a
• /
• pp.514-514
• /
• 2023

댐 건설은 하천의 유황, 유사량을 변화시켜 이·치수 및 생태계에 영향을 미치고 있다. 그러나 현재 댐 운영에 사용하고 있는 하천 기본계획은 10년마다 수립하고 있어 하천 지형 측량자료, 식생 및 수생태를 고려한 하천 관리 계획은 대부분 과거자료이다. 또한 홍수소통에 영향을 미치는 하도식생에 대한 연구가 거의 없어 최근 기후변화로 인해 빈번하게 발생하는 홍수 등 물재해에 적극적 대응이 어려운 실정이다. 따라서 최신의 하천 기초조사 자료 기반, '20년 댐 하류하천에 홍수가 발생한 4개 댐(대청, 합천, 용담, 섬진강댐)을 대상으로 하상변동, 식생 영향 등을 고려한 댐 직하류 하천관리방안을 마련하는 연구를 진행하였다. 최신 하천 기초조사 자료 확보를 위해 하천기본계획 등 문헌정보를 수집하고 댐 직하류의 수중부·육상부 측량, 유사량·하상재료 조사, 식생조사, 홍수흔적조사 등을 실시하였다. 확보한 기초자료를 바탕으로 하상변동 분석 모델 및 물리적 서식처 모의 모델을 통해 이수, 치수, 생태 측면으로 분석을 진행하였다. 이수 분석으로 HEC-RAS의 유사이송 분석을 통해 현재부터 20년 뒤의 하상변동을 분석하였다. 치수 분석으로 HEC-RAS 2D 등의 유사이송 분석을 사용하여 한 개의 홍수기 사상 발생 시 하상변동을 분석하였으며, 식생의 유무가 하상변동에 미치는 영향을 함께 분석하였다. 생태 분석으로는 PHABSIM을 사용하여 대상어종에 대한 하상변동 및 식생 유무에 따른 환경생태영향의 영향을 분석하였다. 분석을 바탕으로 각 대상 댐 직하류에 이수, 치수, 생태 측면의 하천관리방안을 수립하였다. 이수 분석을 통해 20년 뒤의 취양수장의 제약수위를 예측, 검토하고 취약구간 모니터링 구간을 산정하였다. 또한 침식과 퇴적이 크게 일어나는 구간을 산정하여 장·단기 하상변동 모니터링 구간을 제시하였다. 치수 분석을 통해 식생이 댐 하류에 미치는 영향을 분석하여 식생 저감 구간을 선정하는 등 적정 식생 밀도 조절 방안을 제시하였다. 또한 하상변동량이 큰 구간은 하상 안정 유지를 위한 수제 설치를 모델 결과를 통해 검토하였으며 제방 정비가 필요한 구간은 드론을 활용한 모니터링을 제안하였다. 생태 분석을 통해 대상 어종이 서식하기 가장 적합한 환경생태유량을 산정하고 댐 하류 하천의 자연성 회복을 위한 증가방류, 유사환원 등의 방안을 검토하였다.

• Journal of Korea Water Resources Association
• /
• v.57 no.2
• /
• pp.139-150
• /
• 2024

This study introduced a method of estimating water surface evaporation using the physical-based Penman combination equation (PCE) and the Penman wind function (PWF). A set of regression parameters in the PCE and PWF models were optimized by using the observed evaporation data for the period 2016-2017 in the Yongdam Dam watershed, and their effectiveness was explored. The estimated evaporation over the Deokyu Mountain flux tower demonstrated that the PWF method appears to have more improved results in terms of correlation, but both methods showed overestimation. Further, the PWF method was applied to the observed hydro-meteorological data on the surface of Yongdam Lake. The PWF method outperformed the PCE in the estimation of water surface evaporation in terms of goodness-of-fit measure and visual evaluation. Future studies will focus on a regionalization process which can be effective in estimating water surface evaporation for the ungauged area by linking hydrometeorological characteristics and regression parameters.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.29 no.3
• /
• pp.336-342
• /
• 2019

Introduction: An unexpected death was reported in a beginner immediately after starting the work at a plating factory. After the incident, air sampling was performed using a simulation of the situation as it had been at the time. Methods: To evaluate the airborne concentration of hydrogen cyanide, a total of six samples were collected: one personal sample, three area samples, and two background samples (office and outdoors). Hydrogen cyanide measurement was performed according to the standard sampling protocol recommended by the U.S. NIOSH (National Institute of Occupational Safety and Health). Results: The highest concentration of hydrogen cyanide was 0.938 ppm measured in a sample collected from the plating bath area with local exhaust ventilation. This value was approximately 20% of the ceiling occupational exposure limit. The personal sample showed a concentration of 0.135 ppm. Samples collected near the bath in which the incident occurred and a dehydrator showed hydrogen cyanide concentrations of 0.236 ppm and 0.101 ppm, respectively. Hydrogen cyanide was not detected in the background samples (office and outdoors). Conclusions: It is necessary to use proper ventilation systems and respirators in plating factories to prevent acute poisoning. Furthermore, it is important to educate and train new workers dealing with toxic substances.

• The korean journal of orthodontics
• /
• v.35 no.3 s.110
• /
• pp.182-195
• /
• 2005

The purpose of this retrospective study was to estimate the pretreatment characteristics of growing patients with Class II malocclusion. who had been treated with maxillary second molar extractions The sample comprised of 51 subjects; 18 subjects were classified into the molar extraction group, and 33 subjects were treated without extraction and classified into the nonextraction group. Pretreatment lateral cephalograms were calculated and analyzed by independent t-test and stepwise discriminant analysis. In measurements for skeletal pattern, no anteroposterior measurements and proportions of various vertical dimensions were significantly different. and only some measurements such as $AB-MP(^{\circ)$, Na-We(mm), AVD (mm) were significantly different between the two treatment groups (p<0.05). In measurements for dentoalveolar pattern. some measurements, which were related to the position and angulation of the upper and lower permanent first molars, and the angulation of the upper third molars, were significantly different between the two treatment groups In particular, the maxillary second molar extraction group exhibited more mesial angulation of maxillary first molar to the occlusal plane.

• Korean Journal of Applied Biomechanics
• /
• v.15 no.2
• /
• pp.11-20
• /
• 2005

This study has a purpose on contributing to apprehend safe and right way to stop to the inline skate beginners and to the instructors who teaches line skating on the basis for the result of the kinematical analysis on Heel brake stop movement of the inline skate, focusing on the displacement on COG, angle displacement of ankle joint, angle displacement of knee joint, angle displacement of hip joint, using a 3D image method by DLT. To achieve this goal, we analysed the kinematical factor of the 3 well-trained inline skating instructors and obtained the following results. 1. During the movement of heel-brake stop, when strong power was given to a stable and balanced stop and the lower limbs, if the physical centroid is lowered the stability increases, and if it is placed high from the base surface, as the stability decreases compared to the case of low physical centroid, we should make a stop by placing a physical centroid in the base surface and lowering the hight of physical centroid. 2. To make a stable and balanced stop and to provide a strong power to the lower limbs, it is advisable to make a stop by decreasing an angle displacement of ankle joint during a "down" movement. In case of the left ankle joint, in all events and phases the dorsiflexion angle showed a decrease. Nevertheless, in the case of the right ankle joint, the dorsiflexion angle shows an increase after a slight decrease. The dorsiflexion angle displacement of ankle joint can be diminished because of the brake pad of the rear axis frame of the right side inline skate by raising a toe, but cannot be more decreased if certain degree of an angle is made by a brake pad touching a ground surface. To provide a power to a brake pad, it is recommended to place a power by lowering a posture making the dorsiflexion angle of the left ankle joint relatively smaller than that of the right ankle. 3. To make a stable and balanced stop and to add a power to a brake pad, the power must be given to the lower limbs in lowering the hight of physical centroid. For this, it is recommended to make a down movement by decreasing the flexion angle of a knee joint and it is necessary to make a down movement by a regular decrease of the angle displacement of knee joint rather than a swift down movement in every event and phase. 4. The right angle displacement of hip joint is made by lowering vertically the hight of physical centroid as leaning slightly forward. If too narrow angle displacement of hip joint is made by leaning forward too much, the balance is lost during the stop by placing the center in front. To make a stable and balance stop and to place a strong power to the lower limbs, it is recommendable to make a narrow angle by lower the hip joint angle. However, excessive leaning of the upper body to make the angle too narrow, can cause an instable stop and loss of physical centroid. After this study, it is considered to assist the kinematical understanding during the heel brake stop movement of the inline skate, and, to present basic data in learning a method of stable and balanced stop for the inline skating beginners or for the inline skate instructors in the present situation of the complete absence of the study in inline skating.

• The korean journal of orthodontics
• /
• v.31 no.1 s.84
• /
• pp.121-136
• /
• 2001

This study was performed to analyse the expression of VEGF and it's receptor(VEGFR) in the tension side of the periodontal ligament following orthodontic tooth movement. Upper first molars of Sprague-Dawley rats were moved medially using closed coil spring for 1, 2, 24 hours and 3, 7, 14 days. H&E staining, immunohistochemical staining and in situ hybridization methods were used to analyse the change of the expression of VEGF and VEGFR. The results from this study were as follows : 1. Following tensional force, periodontal ligament showed elongation of fibers, compression and congestion of vessels and regional hemorrhage. These tissue changes were recovered within 3 days of force application. New bone formation was seen after 3 days of force application and continued for the remaining experimental periods. 2. Following tensional force, VEGF and VEGF mRNA expression was increased in the periodontal ligament cells, osteoblasts and cementoblasts. This change was followed by increased vasculature in the periodontal ligament. 3. After 3 days of tensional force, VEGF and VEGF mRNA expression was confined mainly to the osteopaths and the periodontal ligament cells adjacent to the alveolar bone. After 2 weeks of force application, VEGF and VEGF mRNA expression was reduced to the level of control sample. 4. VEGFRs(Flt-1, Flk-1) showed similar expression pattern and it's expression was mainly seen in the endothelial cells and osteoblasts. Following tensional force VEGFR expression was increased in the endothelial cells and osteoblasts. In conclusion, in the tension side of the penodontal ligament, ligament cells, osteoblast and cementoblast showed increased expression of VEGF & VEGF mRNA. It preceded the increase of vasculature and new bone formation. The increased expression of VEGF mRNA in cementoblast may induce periodontal vessels, which distribute mainly the bone side half of periodontal ligament, grow in the direction of tensional force. Increased expression of VEGFR & VEGFR mRNA not only in endothelial cell but in osteoblast, osteocyte and periodontal cells showed VEGF acts not only in paracrine manner but in autocrine one.