• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.4A
• /
• pp.352-360
• /
• 2008

Recently Task Group (TG) 4 of the Institute of Electrical and Electronics Engineers (IEEE) 802.15a has been recommended a system with ranging capability in existence of multiple Simultaneous operating piconets (SOPs) as well as low-cost, low-power. According to the ranging service, coherent and non-coherent based ranging schemes using ternary code have been adopted as a standard. However it is hard to estimate an accurate time of arrival (TOA) in case of using direct sequence based TOA estimation method because pulse repetition interval (PRI) offered by TG is more limited than the maximum excess delay (MED) of channel. To mitigate inter pulse interference (IPI) problem, this paper proposes a non-coherent TOA estimation scheme using non-periodic transmission (NPT) pattern. The proposed receiver is based on a non-coherent energy detection considering with motivation of low rate wireless personal area network (LR-WPAN). TOA information is estimated via proper comparison with a prescribed threshold after the sliding correlation and search back window (SBW) process for reducing TOA error. To verify the performance of proposed ranging scheme, two distinct channel models approved by IEEE 802.15.4a TG are considered. According to the simulation results, we could conclude that the proposed scheme have performed better performance than the conventional method on the existence of multiple SOPs.

• Journal of Broadcast Engineering
• /
• v.19 no.3
• /
• pp.372-384
• /
• 2014

DTV field tests have been performed to measure field strength and to check reception ratio on indoor and outdoor sites. They use an antenna of 9m to measure DTV signal in case of outdoor measurement on the road. Modern skyscrapers require the analysis of vertical-directional wave propagation by measuring vertical-directional DTV signal. Even if the field strength is above the reception threshold of $43dB{\mu}V/m$, the reception is impossible in case of strong multi-path or high impulse noise. So, vertical-directional field measurement is essential in environment of tall buildings. In this paper, we developed an octo type multi-copter to measure vertical-directional DTV signal level. A compact and portable DTV signal level meter, an antenna, a microwave transmitter for data transmission, and a recording equipment are equipped in the multi-copter. Three different sites are selected to test the measurement system. Developed measurement system using the multi-copter is very useful in measuring vertical-directional DTV signal, especially in apartments, non-accessible area by vehicles, and forbidden areas.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05b
• /
• pp.37-40
• /
• 1998

Fe량을 0 - 0.4 wt.%까지 변화시켜 Zr-Fe 이원계 합금을 진공아크용해로 제조한 후 1050 $^{\circ}C$에서 30분 균질화 처리 및 700 $^{\circ}C$에서의 열간압연, 그리고 2회의 걸친 냉간압연 및 열처리를 통하여 판재로 제조되었다. 중간 열처리 시 열처리 온도 및 시간을 조절하여 최종 냉간가공에 앞서 각 시편의 결정립 크기 및 경도 값이 같도록 조절하였다. 최종 냉간가공 시 냉간가공량을 60%로 동일하게 조절하였고, 최종열처리 시 열처리 온도 및 시간을 300-750 $^{\circ}C$, 5-3000분으로 각각 변화시켰다. 재결정 정도는 미세조직 관찰 및 경도 측정으로 평가되었으며, 석출물의 구조, 분포 및 형상 등도 TEM으로 분석되었다. 0.1 wt.% 정도까지의 Fe 첨가는 Fe를 첨가하지 않은 순수지르코늄에 비하여 지르코늄입자의 빠른 성장을 야기해, 조대한 재결정 지르코늄 입자들이 나타났다. 그러나 Fe 첨가량이 0.1wt.%이상 첨가되면, Zr$_3$Fe 석출물에 의한 입자성장 억제효과로 지르코늄 입자의 크기는 오히려 작아졌다. 결론적으로, Fe의 첨가는 지르코늄의 확산을 가속시켰다는 것을 보여준다. 한편, 750 $^{\circ}C$에서 열처리 시 이차 재결정현상으로 지르코늄 입자가 비정상적으로 매우 커졌으며, 동시에 annealing twining 현상이 관찰되었다. 이러한 annealing twining 현상은, 입자성장속도가 임계치 이상으로 갑자기 커진, Zr$_3$Fe 석출물이 거의 없는 합금에서만 나타났다. 이 결과를 토대로 annealing twining 현상은 입자의 빠른 이동이 필요 조건이라는 결론을 도출하였다. .Ar-4vol.%H$_2$ 분위기보다 H$_2$분위기에서 소결했을 때 밀도가 더 높았다. 그러나, 결정립은 $UO_2$와 $UO_2$-Li$_2$O의 경우, 수소분위기에서 소결했을 때, (U,Ce)O$_2$와 (U,Ce)O$_2$-Li$_2$O에서는 Ar-4vol.%H$_2$분위기에서 소결했을 때 더욱 성장하였다.설명해 줄 수 있다. 넷째, 불규칙적이며 종잡기 힘들고 단편적인 것으로만 보이던 중간언어도 일정한 체계 속에서 변화한다는 사실을 알 수 있다. 다섯째, 종전의 오류 분석에서는 지나치게 모국어의 영향만 강조하고 다른 요인들에 대해서는 다분히 추상적인 언급으로 끝났지만 이 분석을 통 해서 배경어, 목표어, 특히 중간규칙의 역할이 괄목할 만한 것임을 가시적으로 관찰할 수 있 다. 이와 같은 오류분석 방법은 학습자의 모국어 및 관련 외국어의 음운규칙만 알면 어느 학습대상 외국어에라도 적용할 수 있는 보편성을 지니는 것으로 사료된다.없다. 그렇다면 겹의문사를 [-wh]의리를 지 닌 의문사의 병렬로 분석할 수 없다. 예를 들어 누구누구를 [주구-이-ν가] [누구누구-이- ν가]로부터 생성되었다고 볼 수 없다. 그러므로 [-wh] 겹의문사는 복수 의미를 지닐 수 없 다. 그러면 단수 의미는 어떻게 생성되는가\ulcorner 본 논문에서는 표면적 형태에도 불구하고 [-wh]의미의 겹의문사는 병렬적 관계의 합성어가 아니라 내부구조를 지니지 않은 단순한 단어(minimal $X^{0}$ elements)로 가정한다. 즉, [+wh] 의미의 겹의문사는 동일한 구성요 소를 지닌 병렬적 합성어

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.45 no.6
• /
• pp.122-130
• /
• 2008

In many applications of wireless sensor networks, sensed data can be classified either normal or urgent data according to its time criticalness. Normal data such as periodic monitoring is loss and delay tolerant, but urgent data such as fire alarm is time critical and should be transferred to a sink with reliable. In this paper, by exploiting these data characteristics, we propose a novel energy-efficient data-aware routing protocol for wireless sensor networks, which provides a high reliability for urgent data and energy efficiency for normal data. In the proposed scheme, in order to enhance network survivability and reliability for urgent data, each sensor node forwards only urgent data when its residual battery level is below than a threshold. Also, the proposed scheme uses different data delivery mechanisms depending on the data type. The normal data is delivered to the sink using a single-path-based data forwarding mechanism to improve the energy-efficiency. Meanwhile, the urgent data is transmitted to the sink using a directional flooding mechanism to guarantee high reliability. Simulation results demonstrate that the proposed scheme could significantly improve the network lifetime, along with high reliability for urgent data delivery.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.23 no.6
• /
• pp.558-564
• /
• 2013

Wireless sensor networks (WSNs) contain limited energy resources and are left in open environments. Since these sensor nodes are self-operated, attacks such as sinkhole attacks are possible as they can be compromised by an adversary. The sinkhole attack may cause to change initially constructed routing paths, and capture of significant information at the compromised node. A localized encryption and authentication protocol (LEAP) has been proposed to authenticate packets and node states by using four types of keys against the sinkhole attack. Even though this novel approach can securely transmits the packets to a base station, the packets are forwarded along the constructed paths without checking the next hop node states. In this paper, we propose the next hop node selection method to cater this problem. Our proposed method evaluates the next hop node considering three factors (i.e., remaining energy level, number of shared keys, and number of filtered false packets). When the suitability criterion for next hop node selection is satisfied against a fix threshold value, the packet is forwarded to the next hop node. We aim to enhance energy efficiency and a detour of attacked areas to be effectively selected Experimental results demonstrate validity of the proposed method with up to 6% energy saving against the sinkhole attack as compared to the LEAP.

• Korean Journal of Food Science and Technology
• /
• v.31 no.3
• /
• pp.625-630
• /
• 1999

This work was to study drying characteristics of the brown rice koji, an enzymic health food, using microwave under vacuum. Cooked brown rice was inoculated with Aspergillus oryzae and incubated at $32^{\circ}C$ for 6 days. The brown rice koji was dried by different drying methods: microwave vacuum drying, hot air drying, vacuum drying and freeze drying. Each drier except freeze drier was set to maintain the sample temperature at $40^{\circ}C$. During microwave vacuum drying, the sample reached $40^{\circ}C$ much faster (within $5{\sim}10\;min$) and was dried much faster (2 hrs) than the other drying methods. The initial drying rate of microwave vacuum drying was ten times faster than that of hot air drying. The microwave vacuum drying produced a dry sample of the highly retained enzymic activity, followed by freeze drying, vacuum drying, and hot air drying.

• Korean Journal of Food Science and Technology
• /
• v.30 no.5
• /
• pp.1107-1113
• /
• 1998

This work was to study the potential use of germinated and microwave-vacuum-dried brown rite as a raw material for enzyme food. Brown rice was soaked in water at $15^{\circ}C$ for 2 days and then germinated at $25^{\circ}C$ for 4 days. The germin ated brown rice was then dried by different drying methods: microwave vacuum drying 1(drying only), microwave vacuum drying 2 $(drying{\rightarrow}crushing{\rightarrow}drying)$, hot air drying, vacuum drying and freeze drying. Each drier except freeze drier was set to maintain the sample temperature to be $60^{\circ}C$. During microwave vacuum drying 1 and 2 the sample reached $60^{\circ}C$ much faster (5 min) and was dried much faster (2 to 3 hrs for microwave vacuum drying 1 and 2 than the other drying methods. The initial drying rate of microwave vacuum drying was ten times faster than that of hot air drying. The microwave vacuum drying produced a dry sample of the highly retained enzymic activity, followed by freeze drying, vacuum drying and hot air drying.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.12C
• /
• pp.1133-1143
• /
• 2005

In this paper, we propose an enhanced two-step search scheme for rapid and reliable signal acquisition in UWB systems under multipath channels. The proposed TSS-LS (Two-Step Search scheme with the Linear search based Second step) achieves rapid acquisition performance comparable to the conventional TSS-BS (Two-Step Search scheme with the Bit reversal search based Second step) already proposed by the authors, based on the single-dwell search with two-step thresholds and search windows. However, unlike the TSS-BS which employs the bit reversal search in the second step, the proposed TSS-LS utilizes the linear search in the second step to improve the reliability of signal acquisition. Simulation results with multipath channel models by IEEE 802.15.3a show that the two-step search schemes for the UWB signal acquisition can achieve sig nificant reduction of the required mean acquisition time as compared to general search schemes. In addition, we observe that the proposed TSS-LS achieves quite good bit error rate performance for large signal-to-noise ratios, which is favorably comparable to the case of ideal perfect timing.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.16 no.4
• /
• pp.33-41
• /
• 2006

RSA cryptosystem is of great use in systems such as IC card, mobile system, WPKI, electronic cash, SET, SSL and so on. RSA is performed through modular exponentiation. It is well known that the Montgomery multiplier is efficient in general. The critical path delay of the Montgomery multiplier depends on an addition of three operands, the problem that is taken over carry-propagation makes big influence at an efficiency of Montgomery Multiplier. Recently, the use of the Carry Save Adder(CSA) which has no carry propagation has worked McIvor et al. proposed a couple of Montgomery multiplication for an ideal exponentiation, the one and the other are made of 3 steps and 2 steps of CSA respectively. The latter one is more efficient than the first one in terms of the time complexity. In this paper, for faster operation than the latter one we use binary signed-digit(SD) number system which has no carry-propagation. We propose a new redundant binary adder(RBA) that performs the addition between two binary SD numbers and apply to Montgomery multiplier. Instead of the binary SD addition rule using in existing RBAs, we propose a new addition rule. And, we construct and simulate to the proposed adder using gates provided from SAMSUNG STD130 $0.18{\mu}m$ 1.8V CMOS Standard Cell Library. The result is faster by a minimum 12.46% in terms of the time complexity than McIvor's 2 method and existing RBAs.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.20 no.6
• /
• pp.84-99
• /
• 2021

As the micro-mobility market grows, the demand for route guidance, that includes uphill information as well, is increasing. Since the climbing angle depends on the electric motor uesed, it is necessary to establish an uphill road DB according to the threshold standard. Although road alignment information is a very important element in the basic information of the roads, there is no information currently on the longitudinal slope in the road digital map. The High Definition(HD) map which is being built as a preparation for the era of autonomous vehicles has the altitude value, unlike the existing standard node link system. However, the HD map is very insufficient because it has the altitude value only for some sections of the road network. This paper, hence, intends to propose a method to generate the road longitudinal slope using currently available data. We developed a method of computing the longitudinal slope by combining the digital elevation model and the standard link system. After creating an altitude at the road link point divided by 4m based on the Seoul road network, we calculated individual slope per unit distance of the road. After designating a representative slope for each road link, we have extracted the very steep road that cannot be climbed with personal mobility and the slippery roads that cannot be used during heavy snowfall. We additionally described errors in the altitude values due to surrounding terrain and the issues related to the slope calculation method. In the future, we expect that the road longitudinal slope information will be used as basic data that can be used for various convergence analyses.