• The Korean Journal of Rheology
• /
• v.6 no.1
• /
• pp.49-59
• /
• 1994

높은 전기장 하에서 다분산, 비구형 실리카/실리콘 오일 현탁액의 전기유변 (electrorheological, ER)현상을 살펴 보았다. 전기유변유체는 전기장 방향으로 사슬구조를 형 성하는 특성을 보이며 이것이 유변물성의 향상에 기여하는 것으로 알려졌다. 동적(dynamic) 상태 실험에서 전기장 하의 실리카 현탁액은 매우낮은 임계변형율(${\gamma}$c =0.1%)이상에서 비선 형 점탄성을 보였다. 저장탄성계수(G＇)는 변형율 변화에 손실탄성계수(G＂)는 매질의 점도 에 더 민감한 의존성을 보였다. 또한 겉보기 항복응력은 입자의 부피분율과 전기장에$\Phi$1.9E1.4 의 의존성을 보였는데 부피분율에 대한 의존성이 큰 이유는 0.1 이상의 부피분율에서 복합 사슬 구조 내의 입자들 간의 상호 정전효과가 지배적으로 나타나기 때문이라고 생각된다. 정상상태 실험에서는 부피분율이 크거나 높은 전기장 하에서 전단속도가 0.1sec-1 정도 이하 로 감소함에 따라 전단응력이 급겨히 증가하는 현상을 보였다. 그러므로 본질적인 동적 항 복응력을 얻기 위해서는 매우 낮은 전단속도 영역의 특이한 응력거동을 고려해야한다. 큰 전단속도 하에서는 hydrodynamic interaction의 영향으로 전단속도의 증가에 따라 전단응력 이 증가하였다. 이같은 전단응력의 거동을 계단전단실험으로 확인하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.11a
• /
• pp.525-528
• /
• 2006

아임계 및 초임계수에 의한 목질바이오매스의 당화특성을 분석하기 위하여 분해공정 동안 압력을 23MPa(물의 임계압력)로 고정하고 물의 아임계 온도$(325^{\circ}C,\;350^{\circ}C)$와 초임계 온도$(380^{\circ}C,\;400^{\circ}C,\;425^{\circ}C)$에서 현사시나무 목분을 각각 60초 동안 처리하였다. 생성된 현사시나무의 분해산물에는 액상과 고형분의 분해산물이 섞여 있었다. 각 처리조건에 따른 목질바이오매스의 분해율은 온도가 상승함에 따라 증가하였으며 초임계 온도인 $425^{\circ}C$에서 최고 83.1%의 분해율을 나타냈다. 아임계 및 초임계수에 의해서 생성된 단당류는 고성능 음이온 교환 크로바토그래프(HPAEC)를 이용하여 분석하였다. 목질바이오매스의 초임계수 분해과정에서 처리 온도가 높아지면서 단당류 수율은 증가하는 경향을 보였으며, $425^{\circ}C$에서 가장 높은 7.3%의 단당류 수율을 나타내었다. 아임계 온도 범위에서는 현사시나무의 섬유소 성분 중에서 자일란이 우선적으로 분해되어 자일로스의 생성비율이 비교적 높았으며, 처리온도가 높아지면서 셀롤로오스의 분해에 의한 글루코오스 생성율이 급격히 상승하였다. 이렇게 생성된 단당류 성분들은 고온의 반응조건하에서 열분해 반응에 의해서 더욱 분해되어 퓨란계 화합물로 변형되었다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.1 no.1
• /
• pp.64-72
• /
• 1997

An analytical study has been performed to investigate the unsteady ignition characteristics of pulse combustion. In many combustion applications, strain rate of the flow can significantly affect the combustion features; ignition, extinction, and reignition. In the pulse combustion, two jets (hot combustion gases and fresh mixtures) coming from the opposite side of the combustor will collide in the combustor forming a stagnation region where the chemical reaction is suppressed by the strain rate until this becomes below the critical value. In this research, the method of large activation energy asymptotic is adopted with one step irreversible kinetics to examine the ignition response to the periodic variation of the strain rate of flow. The results show the variation of the maximum value of strain rate can determine whether the ignition or extinction occur.

• Composites Research
• /
• v.17 no.5
• /
• pp.61-67
• /
• 2004

This paper reports the electrical conductivity and the stress-strain behavior of silver particle-filled silicone composite pastes for electromagnetic interference (EMI) shielding gasket materials. The percolation threshold (critical concentration) of the composite paste obtained by incorporating irregular sphere-shaped silver particles and room temperature vulcanizing (RTV) silicone resin was determined from the electrical conductivity result. At about 28 vol% Beading of untreated silver particles, the percolation phenomenon occurred and at this critical concentration, the volumetric resistivity, the tensile strength, and the elongation of the pastes were investigated. This work also suggests that the stress-strain characteristics of a composite paste filled with metal particles above the percolation threshold may be effectively improved by properly selecting a coupling agent.

• Ceramist
• /
• v.12 no.5
• /
• pp.13-20
• /
• 2009

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.385-390
• /
• 2009

The gas turbine engine structures usually are placed on high thermal mechanical stress condition. For general low cycle fatigue evaluation, simple fatigue criterion based on critical plane approach is developed. LCF life of turbine wheel is evaluated with this criterion and process contrived together.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1306-1309
• /
• 2003

In the present paper, finite element analyses were carried out to evaluate the most important feature of a stent, that is. high radial strength and flexibility. Palmaz-Schatz 154 stent and two new models(stent A, stent B) were selected because they are the most representatives of tubular stents. Finite element analyses for the stent system were performed using ABAQUS/Explicit code. As a result, Palmaz-Schatz 154 stent shows sufficient radial strength but it needs some improvement in general properties such as high flexibility, low elastic recoil, low longitudinal contraction and low metal coverage area. Other two models show that sufficient flexibility, foreshortening and longitudinal recoil.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.5
• /
• pp.935-943
• /
• 1988

The forming limit diagram is assessed as a means of estimating the forming characteristics of sheet metal and is usually determined experimentally. The strain rates used in the determination are likely to be low. However, often in practice, the strain rates are much higher, so if forming limit diagram is determined at low rates, it may not be appropriate. This paper reconsiders the forming limit diagram for mild steel and aluminum sheet up to variation in strain rate from 10$^{-2}$ sec to 20/sec where its forming has been carried out under oil pressure using a hydraulic bulge test with circular and elliptical dies. To obtain higher strain rate, an impact bulge test had been employed with the same die sets as those used for a hydraulic bulge test. The results obtained are as follows: (1) As the strain rate increases, the fracture pressure increases and the polar height at fracture decreases. (2) Experiment has shown that, in the positive quadrant of the forming limit diagram, the diagram is lowered with increasing strain rate and the effect of strain rate changes according to strain paths and materials..

• Journal of the Korean Geotechnical Society
• /
• v.30 no.4
• /
• pp.35-45
• /
• 2014

Limit equilibrium methods of slope stability analysis have been widely adopted mainly due to their simplicity and applicability. However, the conventional methods may not give reliable and convincing results for various geological conditions such as nonhomogeneous and anisotropic soils. Also, they do not take into account soil slope history nor the initial state of stress, for example excavation or fill placement. In contrast to the limit equilibrium analysis, the analysis of deformation and stress distribution by finite element method can deal with the complex loading sequence and the growth of inelastic zone with time. This paper proposes a technique to determine the critical slip surface as well as to calculate the factor of safety for shallow failure on partially saturated soil slope. Based on the effective stress field in finite element analysis, all stresses are estimated at each Gaussian point of elements. The search strategy for a noncircular critical slip surface along weak points is appropriate for rainfall-induced shallow slope failure. The change of unit weight by seepage force has an effect on the horizontal and vertical displacements on the soil slope. The Drucker-Prager failure criterion was adopted for stress-strain relation to calculate coupling hydraulic and mechanical behavior of the partially saturated soil slope.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.6 no.1
• /
• pp.18-22
• /
• 2013

Input impedance of the inverted L antenna which is modified from a monopole antenna varies to very high input impedance value when the ratio of vertical height to horizontal length is reduced. So its impedance matching becomes very difficult. In this paper, we analyzed the input impedance variation range depending on the ratio of vertical height to horizontal length in the normal and ferrite thin film added configuration for the input impedance control. For the exact analysis involving the permittivity, permeability and conductivity of ferrite material, FDTD numerical method is used.