• Magazine of the Korean Society of Agricultural Engineers
• /
• v.28 no.2
• /
• pp.74-86
• /
• 1986

유동화콘크리트의 공학적 특성에서 시간-의존거동을 확인하기 위하여,나프타렌 설폰산염 폴리머 고축합물인 Rheobuild 1000과 메라민 설폰산염 고축합물인 NP-20의 고성능감수제를 사용한 유동화콘크리트와 보통콘크리트를 제조하여 비교.고찰을 행하였으며, 고성능감수제의 종류 및 함량이 콘크리트의 공학적 특성에 미치는 영향을 구명하기 위하여 재령 3일, 14일, 28일, 60일, 90일, 180일의 압축강도를 측정, 조기 및 장기압축강도를 조사하였고, 인장강도 및 탄성 변형에 미치는 영향을 조사하였다. 또한 습윤 및 에어콘디션의 양생조건하에서 시간의 경과에 따른 건조수축 및 크리이프 변형을 조사.분석함으로써 유동화콘크리트의 시간-의존거동을 확인하였다. 실험결과, 사용 고성능 감수제의 종류에 따라 차이는 있으나, 고성능 감수제의 사용은 일반적으로 워커빌리티 성능을 개선하고 압축 및 인장도를 크게 향상시키며, 탄성계수는 보통의 콘크리트에 비하여 높게 나타났다. 또한 건조수축 및 크리프 변형의 감소에 매우 양호한 결과를 나타내어 앞으로 건설용 용도로써 효과적인 것으로 판단되었다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.1A
• /
• pp.61-69
• /
• 2010

Unbonded precast concrete piers have better seismic performances than conventional reinforced concrete piers. In this research, seismic performances of unbonded precast prestressed concrete piers are analyzed using OpenSEES. Main parameters of analysis are concrete strength, jacking force ratio, ratio of tendon, and size of precast segment. In results, as the ratio of tendon and jacking force ratio increase, the flexural strength increases at softening state and ultimate state. Concrete strength and size of precast segment are negligible. But initial jacking force ratio leads to early yielding of prestressing tendon. Since compressive strain in core concrete is much less than ultimate strain, it can be expected that the amount of transverse steel reinforcement is to be reduced in comparison with conventional reinforced concrete column.

• Journal of Korean Society of Steel Construction
• /
• v.19 no.5
• /
• pp.473-482
• /
• 2007

When the material strength and ductility of shear studs is sufficient to carry the interface shear force, the composite beam can behave safely without premature structural failure in the interface and without ultimate moment reduction. In this study, the influence of the deformation capacity of shear studs embedded in high-strength concrete on structural behavior and design condition of composite beam is analyzed using FEM. In the analysis, load type, degree of shear connection and arrangement of studs are considered as analysis parameters. According to analysis results, in the case of partial interaction,the deformation capacity of studs embedded in high-strength concrete should be considered together with material strength. Especially in the case of uniform arrangement of studs and uniformly distributed load, a minimum available degree of shear connection is restricted by the deformation capacity of studs. In this case,shear studs should be arranged in consideration of the distribution of shear force at the composite section.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.965-968
• /
• 2008

The KS F 2403 method used on domestic sites for checking the compressive strength of a structure, sets the compressive strength of the concrete used in structural specimens as the compressive strength of testing specimens. Under this regulation, the curing method used for testing the specimens must be the standard ponding curing method (20$\pm$2$^{\circ}$C). However, because in-placed concrete is exposed to open air and cured under the seasonal temperature changes, the compressive strength of a real structure is different from the tested compressive strength. (Therefore,) This thesis first identifies the distinct characteristics of the strength development by applying the curing method listed under the KS and used for testing specimens on compressive strength tests; the atmospheric curing method, the sealed curing method, and the structural specimen core strength testing methods used for the in-sites quality checks including reckoning of the compressive strength of the structural specimens and form-demolding period; and the curing method suggested in this research, which sets the internal conditions of the structural specimens as the conditions of the applied curing method. Then, the thesis suggests the specimen curing method that most closely reenacts the compressive strength of the concrete used on the structural specimens

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.420-421
• /
• 2008

배전설비의 안정성검토 및 조형물과 충분한 측방이격거리 확보검토를 위해 일반지역 직선선로에서 2400mm 완철을 설치한 보통장주와 편출장주 일반용 콘크리트 전주의 강도를 검토하였으며, 편출장주시 완철의 길이변화가 전주강도에 미치는 영향을 살펴보았다. 표준경간[3]에서 보통장주형태의 전주는 대용량선로의 전선(ACSR/AW-OC $240mm^2$)을 설치한 경우에도 허용강도이내였으며, 표준경간에서 편출장주 형태의 전주는 보통장주일때 보다 전주의 휨모멘트는 증가하였고 일반선로 ACSR/AW-OC$160mm^2$ 이하의 전선을 설치한 경우 허용강도를 갖게 됨을 알 수 있었다. 또한, 편출장주 완철의 길이를 2400mm에서 3200mm로 증가시킨 경우, 전주의 휨모멘트는 증가하였으며, 전주는 표준경간이 40M 이하에서 대용량선로의 전선을 설치한 경우에도 허용강도를 갖게 됨을 알 수 있었다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.342-347
• /
• 2016

This study examined the effects of the coarse aggregate maximum size and grading of fine aggregates to acquire the characteristics of very low shrinkage on normal strength concrete mixed in the field. In addition, the shrinkage characteristics of concrete under construction were evaluated in accordance with the curing temperature. The compressive strength and drying shrinkage tests were performed for nine mixing factors composed of the coarse aggregate size (13, 20, and 25 mm), types of fine aggregate (see sand, crushed sand, and blended sand), and curing temperatures (5, 20, and $35^{\circ}C$). To acquire low shrinkage properties under $350{\mu}{\varepsilon}$ strain on normal strength concrete, a 25 mm maximum of coarse aggregate was available, and the grading of fine aggregate affected the shrinkage of concrete. In addition, very low shrinkage properties were acquired in the curing temperature range except cold and hot weather concrete.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.389-392
• /
• 2008

Ultra-high strength concrete becomes one of the main research areas because recently concrete structure is larger. The quality of aggregate (ultra-high strength and uniformity) as well as chemical admixture and mineral additives is a key factor for ultra-high strength concrete development. However, natural aggregate including crushed aggregate is inappropriate for ultra-high strength concrete because ultra-high strength quality cannot be maintained uniformly over whole natural aggregate lot. In this study ceramic aggregate was applied for ultra-high strength concrete in order to assure uniform quality of ultra-high strength aggregate. Ultra-high strength concrete was achieved by applying coated ultra-high strength ceramic aggregate to enhance the bonding strength between aggregate and cement paste. Also for actual application light weight ceramic aggregate(density 2.2 $g/cm^3$) with zero water absorption was tested.

• Journal of the Korea Concrete Institute
• /
• v.26 no.4
• /
• pp.533-543
• /
• 2014

Currently, composite construction of prestressed Precast Concrete (PC) and Cast-In-Place (CIP) concrete with different concrete strengths are frequently used in the modular construction. However, current design codes do not clearly define shear design methods for such composite beams. In this present study, simply supported prestressed PC-CIP composite beams without vertical shear reinforcement or only with horizontal shear reinforcement were tested to evaluate the effect of prestressing on the shear strength and the shear design method for such composite members. The test variables were the area ratio of PC and CIP concretes, prestressing force, shear span-to-depth ratio, and shear reinforcement ratio. The results showed that the shear strength was increased by the increase of prestressing force and prestressed PC area, and the decrease of shear span-to-depth ratio.

• Resources Recycling
• /
• v.31 no.5
• /
• pp.42-51
• /
• 2022

Aggregate resources in Korea are expected to run out owing to an increase in development demand and construction investment. Recycled concrete aggregates (RCA), extracted from waste concrete, have a lower quality than natural aggregates. However, RCA can produce concrete similar in quality to the normal concrete by aggregate pretreatment, use of admixtures, and quality control. RCA are most suitable for use in precast concrete products such as sidewalk blocks and revetment blocks. Herein, the feasibility of producing revetment blocks using recycled aggregate concrete (RAC), similar in quality to normal concrete, was analyzed. The amount of RCA was varied, and moderate high early strength cement and steam curing were used to produce the concrete test blocks. In the block test, the load resistance characteristics of the blocks were evaluated to determine optimal RAC and glass fiber reinforced polymer (GFRP) rebar compositions. Thus, the variable that reduced the cement content was determined at the same level as that of natural aggregate concrete by the control of steam curing. In the concrete block test, although this depends on the reinforcement ratio, the RAC block exhibited the same or better performance than a normal concrete block. Therefore, the low quality of RCA in RAC is no longer a problem when concrete mixing and curing are controlled and appropriate reinforcement is used.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.2
• /
• pp.98-104
• /
• 2018

Nondestructive strength Equations are commonly used to determine the strength of concrete. However, the application of the existing equations may include many errors because this method is proposed on the basis of limited experimental parameters while actual bridges have various parameters such as conditions of concrete mixtures, properties of concrete strength, etc. Also, the error among the existing equations causes the confusion when engineers select the proper estimation equation for the concerned bridge. In this study, a series of the field inspection and the test have been performed on 297 existing bridges, in order to evaluate the bridges, based on the test results of the in-depth inspection, and the estimated strengths by means of the nondestructive strength equations are analyzed and compared with results of the core specimen strengths. According to results of analyses, the nondestructive strength equation proposed by CNDT Committee of Architectural Institute of Japan had high relationship with core strength. However, the strengths predicted by this equation, are underestimated when concrete's strengths are over 30 MPa, otherwise, they are overestimated. Also in this paper, based on the relationship between the estimated nondestructive concrete strengths and the core specimen strengths the modified strength equation through simple correlation analysis is proposed.