• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.1
• /
• pp.28-40
• /
• 1991

Affine transformation was used to analyze the bending, buckling and vibration behaviors of a thick antisymmetric angle-ply rectangular simply supported laminate. Introducing the generalized parameters, the comprehensive solutions are found. The generalized parameters are a generalized rigidity ratio ( $D^*1), a generalized Poisson's ratio (.epsilon.) and a principal rigidity ratio (.alpha.). Hence, the transverse deflection decreases, the uniaxial buckling load and the fundamental frequency increase with increasing $D^*1 and decreasing .alpha., but the effect of .epsilon. is negligible. With decreasing the thickness ratio, the results by the classical plate theory are more erroneous. The transverse deflection is minimum, the uniaxial buckling load and the fundamental frequency are maximum if the fiber angle is 45.deg., and number of plies is more than 4. The time and efforts can be saved to understand the behaviors of composite laminates because these results can be applied to another composite material easily.sily.

• Journal of the Korean Ceramic Society
• /
• v.34 no.3
• /
• pp.257-264
• /
• 1997

The aim of this study was to investigate the degradation of piezoelectric properties with compressive cy-clic loading, the change in bending strength before and after poling treatment and fracture strength in MPB depending on the amount of MnO2 addition. The MPB with 0.25 wt.% MnO2 showed the best resistance against the piezoelectric degradation with compressive cyclic loading. Bending strength increased when pol-ing and loading directions are parallel, however decreased when poling and loading directions are per-pendicular each other. Because, during poling treatment, compressive residual stress is generated in the pol-ing direction but tensile residual stress in the perpendicular direction to poling direction.

• The Journal of Engineering Geology
• /
• v.30 no.1
• /
• pp.43-57
• /
• 2020

The objective of this study was to evaluate the performance of high-strength lattice girders as a possible superior alternative to conventional steel arch ribs. For this purpose, the structural characteristics of supports were analyzed using numerical analysis, and their performance was evaluated using maximum bending load tests and tensile tests of the welded joint. According to the results of structural analysis, the optimum size of the upper and lower members and plates is 50 mm × 31.8 mm × 25.4 mm, demonstrating excellent functionality and economic efficiency. High-strength lattice girders of dimensions 55 mm × 30 mm × 20 mm and 85 mm × 30 mm × 20 mm, determined from bending load tests, are found to meet both the reference values and the target values of H-profiles 100 and 125. A review of the ratio of theoretical deflection to actual deflection shows that the high-strength lattice girder developed during this study meets fewer than five of the evaluation criteria for lattice girder deflections proposed by the Federal Railway Department of Germany. Finally, tensile test results reveal that the welded joint of the high-strength lattice girder at the main steel bar-auxiliary steel bar-plate junction exceeds the target value, indicating that the welded joint has sufficient stability.

• Composites Research
• /
• v.20 no.6
• /
• pp.15-20
• /
• 2007

In this work, the structural response of thin-walled, composite beams with built-in twist angles is analyzed using a mixed beam approach. The analytical model includes the effects of elastic couplings, shell wall thickness, and torsion warping. Reissner's semi-complimentary energy functional is used to describe the beam theory and also to deal with the mixed-nature in the beam kinematics. The bending and torsion related warpings introduced by the non-zero pretwist angles are derived in closed-form through the proposed beam formulation. The theory is validated with available literature and detailed finite element analysis results for rectangular solid section beams with elastic couplings. Very good correlation has been obtained for the cases considered.

• Korean Journal of Agricultural Science
• /
• v.9 no.2
• /
• pp.569-575
• /
• 1982

Mechanical properties of rice plants were tested to determine compressive force, bending force, tensile force and shear force for improvement of harvesting machines and for efficient utilization of rice culm during the proper harvesting period. Rice varieties used in this study were two Japonica varieties with Irri 348 and Jinju, and two $Indica{\times}Japonica$ hybrids with Seogwang and Taebaeg, which were grown in the standard fertilization field of Chungnam Rural Development Office. Also Jinju and Taebaeg were tested to elucidate the shearing characteristics which included shear force-strain relationship, shear force and shear energy according to the position from the ground level, the shearing angle to the rice culm, and the moisture content. 1. Compressive force, bending force, tensile force and shear force were higher In Japonica varieties than $Indica{\times}Japonica$ hybrids. 2. Shear force to overall culm length decreased progressively to upper positions in Jinju variety but a constant shear force was approximately showed between the ground level and the position of 21cm in Taebaeg variety. 3. Shear force and shear energy increased with increase of the cross sectional area, and the rates of increase were high in general up to the cross sectional area of $10mm^2$ and then they became dull very much. 4. Shear force and shear energy decreased with decrease of moisture content of rice culm after cutting up to the moisture content of 60% (w. b.) and then they did not change significantly.

• Korean Journal of Materials Research
• /
• v.4 no.3
• /
• pp.253-258
• /
• 1994

The effect of hole size and hole-to-hole distance in the braided and laminated composite was studied in terms of tensile strength, pin bearing strength, and flexural strength of S2-glass fiber braided polyester. The tensile strength reduction with hole size was well fitted with he Whitney and Nuismer's prediction for the laminated composite. The characteristic distance was measured to be about 1.6mm for braided composite and 1.8mm for laminated one. The effect of distance between the centers of two circu lar holes on tensile strength was negligible when the distance between these two holes was larger than 4 times of the diameter of circular hole for both braided and laminated composite. The side effect was diminished when the center of hole was located 3 times farther than the diamet.er of the hole. The pin bearing strengths was decreased with the size of pin hole for both braided and laminated composite.

• Polymer(Korea)
• /
• v.31 no.2
• /
• pp.123-129
• /
• 2007

Toughening mechanisms and mechanical properties of three different polyolefin-based composite systems we studied using the tensile, Izod impact and double-notch lout-point-bending (DN-4PB) test, which is well known be an effective tool for probing the failure mechanism (s) around the subcritically propagated crack tip. Microscopy observations such as optical microscopy and transmission electron microscopy were carried out lot the test samples. A detailed investigation clearly shows that a variety of toughening mechanisms, i.e., shear yielding, craze, particle-matrix debonding, rubber particle cavitation, crack deflection and bifurcation, are observed around crack tip damage zone. These toughening mechanisms are responsible for the observed, improved fracture toughness. Based on this study, DN-4PB technique is sufficient to obtain the information needed to describe the fracture behavior of polyolefin-based composites as well as their corresponding toughening mechanisms.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.187-187
• /
• 2010

최근 해상풍력 블레이드가 대형화됨에 따라 보다 가볍고 강한 재료가 요구되고 있다. 현재 주로 사용되고 있는 복합재는 발사우드나 PVC 폼 등을 코어소재로 하고, 유리섬유나 탄소섬유 등을 보강섬유로 사용하고 있다. 본 연구에서는 현재 사용되고 있는 복합재에 대한 특성을 알아보고, 최근 흡음, 충격 및 열에 강한 발포 알루미늄을 이용한 복합재를 해상풍력 블레이드 제조에 적용하여, 구조 강도 실험을 실시함으로써 기존 복합재와 구조 강도 및 비용 등을 비교 검토하여 우수한 복합재를 제시하고자 한다. 이를 위해 대형구조물인 블레이드를 제작하기 위해 적절한 크기의 발포 알루미늄을 상호 접합하기 위한 방법을 연구하고자 하며, 목포대학교에서 보유중인 만능재료시험기(100 Ton)를 활용하여 인장, 압축, 굽힘 실험을 실시하고, 스킨재 변화, 코어재의 밀도와 두께 변화를 고려하여 다양한 복합재의 강도를 비교하고자 한다. 또한, 기존에 사용되고 있는 복합재와 발포 알루미늄을 이용한 복합재의 재료비 및 가공비를 추정하고 경제적인 복합재를 제시하고자 한다.

• Composites Research
• /
• v.12 no.3
• /
• pp.84-90
• /
• 1999

High alumina cement(HAC) and polyvinyl alcohol(PVA) based macro-defect-free(MDF) cement composites were reinforced using short carbon fibers, 3mm in length, 1-4% in weight fraction and insoluble polymers such as polyurethane, epoxy, phenol resin, in order to increase mechanical properties and water stability. The specimens were manufactured by the low heat-press(warmpress) method. In addition, the interface and the cross-linking reaction of cement and polymers was also studied by the SEM and TEM. Flexural strength of HAC/PVA based MDF cementitious composites was proportionally decreased with increasing fiber contents due to the undensified structure around fibers. The flexural strength of insoluble polymer added specimen was decreased with increasing fiber contents, while water stability was dramatically improved. Epoxy resin added specimen showed the highest strength with increasing fiber contents, compared with other specimens. The water stability of fiber content 4% added specimen immersed in water presented about 95%, 87% at 3 and 7 days immersed in water, respectively. The interfacial adhesive strength of fiber-matrix was very much improved due to cross linking reaction of polymer and metal ions of cement. Tensile strength of insoluble polymers added composites as linearly increased with increasing the fiber contents. The epoxy resin added specimen also showed highest tensile strength. The 4% fiber added specimen presented 30~80% higher strength than controlled specimen.

• Composites Research
• /
• v.14 no.6
• /
• pp.1-8
• /
• 2001

In this paper, the sandwich panel composites consisting of core material and face sheet were studied to evaluate the mechanical properties, noise level and fire resistance including flammability, smoke, and toxicity. Four types of sandwich panel were prepared using various kinds of panel and honeycomb materials. It was observed that Al honeycomb/Al skin composite materials had the excellent flatwise tensile strength and edgewise compressive strength compared with other types of composites. The flatwise compressive strength and flexural strength of Nomex honeycomb/Al skin composite were higher than those of other composites. PMI form/Al skin composite showed the higher core shear strength and facing bending strength. From the experimental results of flame resistance tests, it can be said that the phenol based skin composite has the excellent flame retardation properties, which are similar to those of the commercial skin composites.