• Proceedings of the Korea Concrete Institute Conference
• /
• 1990.04a
• /
• pp.102-107
• /
• 1990

The research program is directed at studying the behavior and the strength of reinforced concrete slabs subjected to certain combination of punching shear and in-plane tension. Major variables to be investigated are the shear span to depth ratio of reinforced concrete slabs and the degree of the in-plane tensile force which is acting tangent to the slabs. The experimental results are used for understanding of the degree of the interaction between the two loadings, and for developing a new practical design equation.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.197-200
• /
• 2005

This paper presents an analytical model for evaluation of Tension Stiffening Effect by actual Bond-Slip relationships between the reinforcement and the surrounding concrete. The presence of longitudinal splitting cracks was found to significantly after the tension stiffening. The model is applied to the longitudinal splittings cracks and derived to Tension stiffening model. The predicted values are shown to be in good agreement with the experimentally measured data.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05a
• /
• pp.374-377
• /
• 2006

The measured longitudinal reinforcement tensions in the shear-critical RC beams were significantly higher than the calculated values by the beam theory. This may be attributed to the reduction of the internal-moment arm length by the development of the arch action. In this paper, the measured longitudinal reinforcement tensions in the test performed by Kim were compared with those predicted by the new truss model on the basis of the compatibility condition of the shear deformation.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04a
• /
• pp.315-320
• /
• 1998

The experimental set-up and one-dimensional analytical model have been developed to investigate the tensile behavior of reinforced concrete member due to restrained drying shrinkage. The experimental results have been compared with the analytical prediction of the maximum residual stress of steel and concrete due to restrained shrinkage. The tensile residual stress concrete by one-dimensional bilinear model shows 0.19 and 0.63 of tensile strength for 0.83% and 3.29 of steel ratio. The residual tensile stress of concrete increases as the steel ratio increases. The effect of steel fiber has not influenced the residual stress due to restrained shrinkage of concrete.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1998.10a
• /
• pp.141-148
• /
• 1998

An analytical model which can simulate the post-cracking behavior of reinforced concrete structures subjected to in-plane shear and normal stresses is presented. Based on the force equilibriums, compatibility conditions, and bond stress-slip relationship between steel and concrete, a criterion to simulate consider the tension-stiffening effect is proposed. The material behavior of concrete is described by an orthotropic constitutive model, and focused on the tension-compression region with tension-stiffening and compression softening effects defining equivalent uniaxial relations in the axes of orthotropy. Correlation studies between analytical results and available experimental data are conducted with the objective to establish the validity of the proposed model.

• Journal of the Korean Society of Industry Convergence
• /
• v.9 no.2
• /
• pp.155-160
• /
• 2006

합성상판을 시공하는 경우 교축방향에 분할된 저강판을 접합 일체화해야 한다. 본 논문에서는 강 콘크리트 합성상판을 대상으로 3종류의 배력철근 방향 이음구조를 제안하며, 보 공시체에 의한 정적 정점피로 실험한다. 그 결과 보의 피로실험 결과 저강판 혹은 고력볼트가 피로파단 하였으며, 3차원 FEM해석에 이음부의 휨 강성도 및 피로강도에 대해서 해석적으로 검토된다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.1
• /
• pp.115-130
• /
• 2013

The sectional methods of current design codes have been broadly used for the design of various kinds of reinforced concrete pile caps. Lately, the strut-tie model approach of current design codes also became one of the attracting methods for pile caps. However, since the sectional methods and the strut-tie model approach of current design codes have been established by considering the behaviors of structural concrete without D-regions and two-dimensional concrete structures with D-regions, respectively, it is inappropriate to apply the methods to the pile caps dominated by 3-dimensional structural behavior with disturbed stress regions. In this study, the refined 3-dimensional strut-tie models, which consider the strength characteristics of 3-dimensional concrete struts and nodal zones and the load-carrying capacity of concrete ties in tension regions, are proposed for the rational analysis and design of pile caps. To examine the validity of the proposed models and to verify the necessity of appropriate constituent elements for describing 3-dimensional structural behavior and load-transfer mechanism of pile caps, the ultimate strength of 78 reinforced concrete pile caps tested to failure was examined by the proposed models along with the sectional and strut-tie model methods of current design codes.

• Journal of the Korea Concrete Institute
• /
• v.27 no.1
• /
• pp.37-44
• /
• 2015

This paper describes the effect of strain hardening cement composite (SHCC) material on structure performance of reinforced concrete (RC) beams with high-strength reinforcing bar. Also, this paper explores the structure application of SHCC in order to mitigation cracking damage and improve the ductility of flexural RC members. The prediction model for flexural strength of doubly reinforced SHCC beams are investigated in this study. To achieve the these objectives, a total of 6 rectangular beam specimens were tested under four point monotonic loading condition. The main parameters included the types of cement composite and reinforcing bar. Test results indicated that reinforced beam specimens with SHCC material were improved the structure performances and damage characteristics. Specifically, replacement of conventional high-strength concrete with SHCC materials has the potential of high-strength steel bar as flexural reinforcement on RC members. It is remarkable that suggested method of reinforced SHCC beams with high-strength reinforcing bar could be used usefully to the structure design.

• Journal of the Korea Concrete Institute
• /
• v.29 no.1
• /
• pp.33-42
• /
• 2017

This study conducted uniaxial tension tests on D10, D19, D29, and D35 SD400 steel-grade rebar and evaluated the strain distributions and necking regions to provide basic data for resolving differences between evaluation methods. Owing to the limitations of the existing measurement methods, this study conducted detailed evaluations of the strain of the rebar and necking regions using image processing, which is almost limitless on the measurement range and can easily distinguish measurement regions. The strain was concentrated at the region where necking occurred when the rebar approached its ultimate strength, which was successfully confirmed through image processing. The correlation between the length of the necking region and the diameter of the rebar could be analyzed by evaluating the necking region that occurs during the ultimate behavior of the rebar. According to the results, the length of the necking region is around 1.5~2.5 times the diameter of the rebar.

• International Journal of Highway Engineering
• /
• v.12 no.4
• /
• pp.101-110
• /
• 2010

In this paper, it has been studied about the CRCO to maintain or rehabilitate the aged JCP. The CRCO and JCO was constructed at useless section of Seo-Hae-Ahn express highway in South Korea. The performance evaluation was conducted. Especially, it was focused on the roll of longitudinal reinforced steels inserted into the CRCO. On crack survey results from field construction section, the reflection cracks at joint of the existing pavement occurred in CRCO. However, due to the constraints of longitudinal reinforced steels, crack width was small. Total crack length and quantity in the CRCO more than that in the JCO. And crack spacing in the CRCO was narrower than it in the CRCP. Through the bonding strength test results, if the cold milling and cleaning as well as surface treatment is applied, there will be no debonding problem at interlayer in the early age. From analysis of the horizontal behavior at the joint, the longitudinal reinforced steels constrained crack width which became wider than initial state over time. Also, that steel in the CRCO reduced the horizontal movement due to temperature variation(4 times than that in the JCO). But, if interface is debonded, the roll decreased. Vertical VWG data showed that CRCO did not occur debonding problem at steel location, but there was some problem in JCO. It was confirmed by field coring. The tensile strain appeared in the CRCO, But the compressive strain occurred in the JCO in early age. Through the FWD test result, deflection in the CRCO was less than that in the JCO. And K value in the CRCO was greater than it in the JCO.