• Magazine of the Korea Concrete Institute
• /
• v.10 no.2
• /
• pp.137-146
• /
• 1998

본 연구에서는 콘크리트 속에서 인장과 전단을 받는 FRP 다우얼의 거동과 파괴를 예측할 수 잇는 수리적인 파괴 해석 모델을 개발하였다. 다우얼 파괴해석 모델은 다우얼 작용과 파괴기준에 대한 두 개의 하위 모델로 구성되어 있는데 이들을 수정, 결합하여 만들어졌다. 다우얼 작용에 대한 모델로는 BEF 모델을 기초로 하여 두가지의 지수를 새로이 정의, 사용하였는데 하나는 콘크리트지지 강성을 변화시키기 위한 변위 정도 지수이고 다른 하나는 긴장된 케이블의 반력을 고려하기 위한 인장 지수이다. 인장과 전단이 작용하는 FRP다우얼의파괴 모델로는 Tsai-Hill 파괴기준이 사용되었고 이 기준을 적용하기 위하여 파괴 계수를 정의하였다. 개발된 파괴 해석 모델은 긴장된 FRP다우얼의 극한 전단력과 극한 변위를 예측하는데 사용하였고, 해석결과는 여러 인장응력을 가진 FRP 다우얼의 시험결과와 비교하였다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.6
• /
• pp.47-54
• /
• 2023

In this study, the tensile behavior of concrete specimens reinforced with GFRP (Glass Fiber Reinforced Polymer), BFRP (Basalt Fiber Reinforced Polymer), and CFRP (Carbon Fiber Reinforced Polymer) bars was experimentally analyzed. The tensile strength of the FRP bars is appeared to be similar to the design strength, but the elastic modulus was somewhat lower. Additionally, the specimens for tension stiffening effect were manufacured using OPC (Ordinary Portland Cement) and SFRC (Steel Fiber Reinforced Concrete), with dimensions of 150(W)×150(B)×1000(H) mm. The crack spacing of specimens was most significant for GFRP reinforcement bars, which have a lower elastic modulus and a smoother surface, while BFRP and CFRP bars, with somewhat rougher surfaces and higher elastic moduli, showed similar crack spacings. In the load-strain relationship, GFRP bars exhibited a relatively abrupt behavior after cracking, whereas BFRP and CFRP bars showed a more stable behavior after the cracking phase, maintaining a certain level of tension stiffening effect. The tension stiffening index was somewhat smaller as the diameter increased, and GFRP, compared to BFRP, showed a higher tension stiffening index.

• Tunnel and Underground Space
• /
• v.29 no.2
• /
• pp.124-134
• /
• 2019

Subcritical crack growth in rock material can occur under monotonic and cyclic loading. Subcritical crack growth plays an important role in evaluating the long-term stability of structures in rocks. This paper presents the results of studies conducted to determine subcritical crack growth parameters under monotonic and cyclic loading in rock-like material. The constant stress rate method was employed for monotonic loading. The subcritical crack growth parameter of n under cyclic loading was determined by the relation between the rate of crack growth per cycle and stress intensity factor range. The specimens contained pre-existing flaws with 45 and 60 degrees of inclination angle and flaws spacing and continuity were varied to arrange crack growth in shear or tensile manner. The results show that the parameter of n is almost constant regardless of the applied load conditions such as monotonic and cyclic or shear and tension.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2001.04a
• /
• pp.63-70
• /
• 2001

Sodium persulfate, prestogen W, prestogen EB, citric acid 및 thiourea의 첨가에 따른 $H_2O_2$ 표백 효과가 연구되었다. Sodium persulfate(1%), Prestogen EB(15.0%)를 $H_2O_2$ 활성제로 첨가하여 표백할 경우 기존 $H_2O_2$ 표백(86.0% ISO)보다 표백 펄프의 백색도가 2-3% ISO 더 증가하였다. $H_2O_2$ 표백 후 thiourea를 첨가하여 표백하는 산화-환원 연속표백(87.9% ISO)에서도 $H_2O_2$ 표백 후 FAS로 2단 표백(88.3% ISO)을 한 경우와 비슷한 백색도를 나타내었다. 한편 표백 펄프의 인장지수, 파열지수 그리고 인열지수는 기존 표백 또는 Prestogen EB를 첨가할 경우 높고 sodium persulfate 첨가에서 가장 낮았다. 산화-환원 연속 표백된 펄프의 강도도 기존 $H_2O_2$ 표백보다 미세하게 낮았다.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.441-444
• /
• 2010

대공간 구조물과 초고층 빌딩에 있어 건축물의 자중 감소에 대한 요구가 늘어나고 있으며 이에 대한 가장 효과적인 방법 중 하나는 경량 콘크리트를 사용하는 것이다. 본 연구는 최외단 철근의 순인장 변형률에 따른 경량콘크리트 보의 휨 거동 및 휨 성능을 평가하는 것에 그 목적이 있다. 크기와 형상이 동일한 보통중량 콘크리트 보 1개와 경량 콘크리트 보 4개의 총 5개 시험체를 제작하여 최외단 철근의 순인장 변형률을 변수로 실험을 수행하였으며 이를 통해 순인장 변형률에 따른 경량콘크리트 보의 강도와 연성의 변화를 분석하였다. 실험 결과 최외단 철근의 순인장 변형률이 증가할수록 시험체의 연성비는 증가하였으며 최대하중과 강성은 감소하였다. 특히 순인장 변형률 0.005 이상에서 연성지수 2 이상을 확보할 수 있었다.

• Tunnel and Underground Space
• /
• v.18 no.3
• /
• pp.194-201
• /
• 2008

In order to investigate the characteristics in tensile strength of transversely isotropic rock, a new anisotropic tensile failure function was suggested. According to the function, the tensile strength is minimum in the normal direction to a weakness plane and rises exponentially to its maximum on a plane perpendicular to the weakness plane. The anisotropic function is defined in terms of three strength parameters which can be identified trom direct tensile tests of transversely isotropic rocks. By incorporating the suggested function into the critical plane approach, a numerical procedure which enables to search the tensile strength and the direction of critical plane at failure was presented. The validity of the suggested numerical procedure was checked through the simulation of direct tensile tests reported in a literature. The numerical results from the simulation were in good agreements with those from the laboratory tests.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.05a
• /
• pp.729-734
• /
• 1995

원자력용 316L강에 질소를 첨가한 경우의 고온 인장성질을 조사하였다. 온도가 증가하면 인장강도는 감소하다가 온도범위가 30$0^{\circ}C$~50$0^{\circ}C$에서는 일정한 값을 나타낸 후 급격한 감소를 나타내었고 연신율은 감소하다가 40$0^{\circ}C$에서 최소값을 나타낸 후 다시 증가하는 경향을 나타내었다. 질소를 첨가하면 인장강도증가와 함께 연신율도 증가하였다. 동적변형시효 온도구간에서 변형속도변화에 따른 인장강도 및 연신율의 변화는 매우 작다. 동적변형시효를 위한 활성화에너지를 구해본 결과 동적변형시효를 일으키는 원소는 Cr이다. 질소를 첨가하면 동적변형시효가 발생되는 온도가 고온 쪽으로 이동되었는데 이것은 질소가 Cr과의 상호작용에 의해 Cr의 확산속도를 낮추기 때문이다. 가공경화지수는 동적변형시효와 회복의 영향으로 40$0^{\circ}C$에서 최대값을 나타내었으며 이 온도는 연신율이 최소값을 나타내는 온도와 인장강도가 일정하게되는 온도와 일치하므로 강도강화기구는 동적변형시효로 판명되었다.

• Journal of the Korea Concrete Institute
• /
• v.26 no.2
• /
• pp.159-169
• /
• 2014

This study generalizes the lateral load-displacement relationship of reinforced concrete shear walls from the section analysis for moment-curvature response to straightforwardly evaluate the flexural capacity and ductility of such members. Moment and curvature at different selected points including the first flexural crack, yielding of tensile reinforcing bar, maximum strength, 80% of the maximum strength at descending branch, and fracture of tensile reinforcing bar are calculated based on the strain compatibility and equilibrium of internal forces. The strain at extreme compressive fiber to determine the curvature at the descending branch is formulated as a function of reduction factor of maximum stress of concrete and volumetric index of lateral reinforcement using the stress-strain model of confined concrete proposed by Razvi and Saatcioglu. The moment prediction models are simply formulated as a function of tensile reinforcement index, vertical reinforcement index, and axial load index from an extensive parametric study. Lateral displacement is calculated by using the moment area method of idealized curvature distribution along the wall height. The generalized lateral load-displacement relationship is in good agreement with test result, even at the descending branch after ultimate strength of shear walls.

• Journal of Conservation Science
• /
• v.29 no.1
• /
• pp.47-54
• /
• 2013

The following study tests for the effects of mordants on the production of restoration papers during the conservation process of damaged paper artifacts. For this, four different types of synthetic mordants that are being marketed currently ($K_2CO_3$, $AlK(SO_4)_2{\cdot}12H_2O$, $Cu_2SO_4{\cdot}5H_2O$, $FeSO_4$) were selected to produce samples for measuring variable properties through artificial degradation. The research conducts tests for changes in color, tensile index, and pH level (degree of acidity). The results for changes in color have shown that the value of ${\Delta}E^*ab$ of $K_2CO_3$ mordant sample was the highest, and the tests for tensile index have shown that the strength of dyeing sample was decreased in accordance with the aging time, but Changes according to the mordant was not evident. Finally, the findings for pH level have shown that samples with $Cu_2SO_4{\cdot}5H_2O$ and $FeSO_4$ have pH levels drop below 6. As a result, the research have concluded that mordants used for dyeing restoration paper were identified to have an affect in the dyeing and aging characteristics of the paper.

• Explosives and Blasting
• /
• v.21 no.4
• /
• pp.23-35
• /
• 2003

This study is to clarify the comparative relationship and a mechanical anisotropy of rock on the subject of granite distributed in the Namwon area Uniaxial compressive and Brazilian strengths with respect to the horizontal and vertical axes of granite are shown the linear relation. In the case of the result of the p-wave velocity measurement. it is represented that the velocity of vortical direction is faster about 10 to 15% than other two horizontal directions. The difference between velocities is caused by a developmental pattern of microcracks distributed in rock. Moreover, this result is very consistent with the result investigated through thin sections. The proportion of uniaxial compression strength to Index of point load strength ($Is_{(50)}$) is 18~20 times in case of granite. Uniaxial compressive strength is relatively good relationship with point load strength, Schmidt hammer rebound value, and tensile strength point load strength of them is the best comparative relationship. It is indicated that point load test is the most useful tool to estimate uniaxial compressive strength, comparing with other experimental methods.