• Korean Journal of Agricultural Science
• /
• v.13 no.1
• /
• pp.90-102
• /
• 1986

This study was performed to obtain the basic data which can be applied to the use of concretes. The data was based on the properties of concrectes depending upon water-cement ratios and addings to compare those of plain concrete. The results obtained were summarized as follows; 1. In case the proper quantity of water reducing agent was added, unit weight of water is decreased to 12.9% with WR-LG of water reducing set standarding agent and to 8.6% with HF-SP of high fluid agent and to 17.2% with AH-WR of water reducing set accelerating agent, respectively, as compared with plain concrete. With the increase of water reducing agent content unit weight of water was greatly decreased. 2. The adding rate of water reducing agent which produce maximum strength was 0.2% with WR-LG and 0.4% with HF-SP and AH-WR, respectively. The increasing rates of strengths were showed that WR-LG is 24.1% and that HF-SP is 41.8% and that AH-WR is 43.3%, respectively, as compared with plain concrete. 3. The correlations between compressive and tensile strength were highly significant as a straight line. the multiple regression equations of compressive and tensile strength were computed with the variables of curing age and addition of water reducing agent. They were highly significant. 4. In case the proper quantity of water reducing agent was added, the correlations between water-cement ratio and compressive strength were highly significant as a straight line. The increasing rates of strength were showed higher than the decreasing rates of water cement-ratio.

• Journal of Welding and Joining
• /
• v.32 no.6
• /
• pp.56-63
• /
• 2014

To develop and understand dissimilar metals joining of Stainless steel and Copper, ultra-high speed laser lap welding was studied using single mode fiber laser in this study. SUS304 and Cu have large differences in materials properties, and Cu and Fe have no intermetallic compounds by typical binary phase of Cu and Fe system. In this study, ultra-high speed lap welds of SUS304 and Cu dissimilar metals using single-mode fiber laser was generated, and weldability of the weld fusion zone was evaluated using a tensile shear test. To understand the phenomenon of tensile shear load, weld fusion zone of interface weld area and fracture parts after tensile shear test were observed using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) analysis system. And it was confirmed that Cu was easily melting and penetrating in the grain boundaries of SUS304 because of low melting temperature. And high thermal conductivity of copper occurred dissipate heat energy rapidly. These properties cause the solidification cracking in weld zone.

• Journal of Adhesion and Interface
• /
• v.17 no.4
• /
• pp.136-140
• /
• 2016

In this study, a series of dimer acid-based polyamides with different diamines were synthesized by condensation polymerization and the polyamides were characterized by Fourier transform infrared spectroscopy (FT-IR). Effects of diamine structures on mechanical and thermal properties of polyamides were investigated. The tensile strength and lap shear adhesion strength of aromatic-based polyamide (DAP) were higher than those of aliphatic-based polyamide (DAH). In DSC thermogram, DAP has a high $T_g$ and $T_m$ compared with DAH. DAP's and DAH's softening point were $112-115^{\circ}C$ and $98-121^{\circ}C$, respectively.

• International Journal of Highway Engineering
• /
• v.10 no.2
• /
• pp.205-219
• /
• 2008

The polymers, low-density polyethylene (LDPE) and styrene-butadiene-styrene(SBS) -modified asphalt mixtures are advanced asphalt pavement materials in which $3{\sim}6%$ of them, and/or some other additive, by weight of total binder are added. The purpose of modifying asphalt material is to improve typical weakness such as rutting and cracking resistance of normal asphalt mixtures. These materials have been proved to show many advantages and practical applicability in the plant and field. Wet processed PMA binder and/or dry processed asphalt mixtures are developed as field products for many years. The objective of this paper is to show the characteristics of the LDPE and SBS-modified asphalt mixtures by comprehensive evaluation and comparison with those of normal asphalt mixtures.

• Journal of the Korean Society for Heat Treatment
• /
• v.33 no.4
• /
• pp.161-172
• /
• 2020

The tensile property of A5082 and A6060 aluminium wrought alloys was investigated, in terms of the strain rate sensitivity on alloy conditions by heat treatment and bake hardenability on pre-strain prior to strain ageing. The tensile test was carried out in a range of strain rate of 4.17 × 10^-5 s^-1 ~ 4.17 × 10^-5 s^-1 in room temperature and the nominal range of pre-strain was 3.0 ~ 10.5%. The tensile deformation of A5082 alloys is characterized as typical case of dynamic strain ageing with negative strain rate sensitivity for all conditions, and the tensile strength indicates a similar level regardless of alloy conditions, except only in full annealed condition. The stress-relief annealing on A6060 alloys can induce practical decrease in strength level of over approximately 100 MPa without any ductility loss, compared to as-rolled condition, while a full annealed and aged condition leads remarkable strengthening effect with the decrease of tensile elongation. Additionally, the bake hardenability of A5082 alloy by strain ageing indicates a negative dependence upon the increase of pre-strain, while A6060 alloy exhibits a positive sign even in low level relatively compared with conventional SPCC.

• Applied Chemistry for Engineering
• /
• v.27 no.1
• /
• pp.50-55
• /
• 2016

Aromatic diamines containing hexafluoroisopropylidene and ester moiety were synthesized from 4,4'-hexafluoroisopropylidene diphenol and nitrobenzoyl chloride. The reaction of aromatic diamines with hexafluoroisopropylidene phthalicdianhydride (6FDA) or pyromellitic dianhydride (PMDA) gave four kinds of poly(amic acid)s. Their inherent viscosities ranged from 0.196 to 0.346 dL/g. Poly(amic acid)s were converted to polyimides by thermal imidization. The glass transition temperatures ($T_g$) of polyimides were between 241 and $289^{\circ}C$. The 5% weight loss temperatures were recorded in the range of $430{\sim}492^{\circ}C$. The tensile strength of polyimide films were measured as 29.84~64.38 MPa.

• Applied Chemistry for Engineering
• /
• v.16 no.1
• /
• pp.39-44
• /
• 2005

In this study, polyurethane-acryl emulsion resins were synthesized from HDI (hexamethylene diisocyanate), IPDI (isophorone diisocyanate), Polyol, 2-HEMA (2-hydroxy ethylmethacrylate), n-BA (n-butyl acrylate) and MMA (methylmethacrylate). The effects of polyol types on the properties of polyurethane-acryl emulsion resin, such as degree of strength and water resistance and on the manufacturing process were investigated. In addition, the results were compared with those of acrylic emulsion. The test results showed that polyester type polyol demonstrated stronger tensile strength and higher water resistance with time than did acrylic emulsion and polyether type polyol.

• Applied Chemistry for Engineering
• /
• v.16 no.1
• /
• pp.101-106
• /
• 2005

Photocurable modified 6 functional polyacrylate(PA-1) were prepared from dipentaerythritol derivatives (DPET) and acrylic acid, and 12 functional polymethacrylate(PA-2) were prepared from dipentaerythritol derivatives (DPET), trimellitic anhydride, and glycidyl methacrylate. And physical properties of photocurable modified poly(meth)acrylate were increased with increasing functionality of (meth)acrylate. Thermal stability of UV cured film obtained by using TGA was shifted to higher temperature as the increasing of functionality. Hardness, abrasion resistance and tensile strength of UV cured film were increased with increasing functionality of (meth)acrylate. Values of yellow index were increased with increasing functionality of (meth)acrylate.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.3
• /
• pp.955-960
• /
• 2012

In this study, pure Polyurethane and commonly used flame retardants $Al(OH)_3$ and $Mg(OH)_2$, the add-in sample and Cloisite Na+, Cloisite 15A added sample of flammability and mechanical properties are compared. Sodium silicate and a mixture of polyurethane that the lightweight filler Vermiculite, Perlite addition of flame retardant and mechanical properties of the sample was confirmed. As a result, the flame retardant additive in the Vermiculite and Perlite in a flame-retardant grade sample except sample were identified. Tensile strength is degrade accord to the filler amount. But, Sodium silicate in the case of the sample add-in, other than confirmed that the sample strength increases.

• Composites Research
• /
• v.12 no.6
• /
• pp.8-14
• /
• 1999

This research is focused on the investigation of impact strength and the microscopic observation of material behavior of glass fiber reinforced polypropylene in solid phase forming. The fiber weight per-centage of the composite materials was 20%, 30% and 40%. The solid-phase formed specimens were pre-strained to 10%,20%. and 30% strain levels. The forming temperatures of specimens were $100^{\circ}C$, $125^{\circ}C$ and $150^{\circ}C$. Izod impact test was performed with unnotched specimens. With increasing the glass fiber content ; the impact strength was increased.