• Journal of IKEEE
• /
• v.23 no.4
• /
• pp.1280-1287
• /
• 2019

Grid-connected bidirectional PCS(Power Conditioning System) technology is a technology for implementing distributed renewable energy smart grid. And it is always charged by using power collected from solar modules and commercial grid power among vast smart grid systems, and stored when needed.It is a hybrid energy storage device that allows power to be released into the low voltage system. To this end, a PV input power converter with MPPT function, a bidirectional power converter for battery charging and discharging, and a DC Link input are output to a 3 phase 380V AC system, and if nessary, the bidirectional DC/DC converter We designed and developed a PCS with three power converter structures composed of inverters that perform battery charging. Currently, this system is applied to the site of Jeju, which is vulnerable to power outages and fire accidents.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.7
• /
• pp.706-712
• /
• 2014

The inverters used to drive Brushless DC motors (BLDC) include switching devices such as FETs and the faults in FETs cause severe performance degradation in systems where a BLDC acts as actuator. This paper presents a fault detection and isolation method for the FETs of an inverter for BLDC motor control systems, which is based on the EKF (Extended Kalman filter). Firstly, an equivalent circuit model for a BLDC motor plus its inverter system was derived. Secondly, a state-space equation was established, where the on-resistance of the FETs is expressed as a state variable and the EKF equation estimates the on-resistance. If the estimated resistance differs greatly from the known value, it can be asserted that there is a fault on that FET. Thirdly, the local convergence of the established EKF was proved. Finally, through the experiments, the performance of the proposed method was verified. The results show that the on-resistance is estimated close to the value specified in the FET data sheet in normal operation, whereas the estimated resistance is a much larger value than the normal one in case an FET fault occurs. Therefore, it is confirmed that the proposed fault detection and isolation method works appropriately in real systems.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.5
• /
• pp.482-485
• /
• 2016

In this work, a transcranial magnetic stimulation(TMS) experiment on animals is performed to stimulate the brain cortex of the mouse using modulated signals. The proposed TMS system is composed of the inverter, transformer, capacitor, variable inductor, and stimulation coil to generate 1.5 mT magnetic field in the brain cortex of the mouse. The stimulation signal is modulated to square wave where the carrier frequency is swept from 85 to 91 kHz to investigate the stimulation effect. The experimental result shows that when the carrier frequency of the stimulation signal is lower than 89 kHz, the reaction of the mouse does not change while the stimulation signal which has the carrier frequency higher than 89 kHz results in decreasing the threshold of the stimulus for the pressure.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.5
• /
• pp.305-311
• /
• 2016

Induction heating is the process in which an electrically conducting object (usually a metal) is heated by electromagnetic induction through heat generated in the object by eddy currents. The main advantage of an induction heating device is the generation of the heat inside the target object itself. Hence, non-contact and safe heating devices are widely used in many industrial and medical fields. Recently, a new dental implant system was developed using a shape-memory alloy, wherein an artificial tooth could be easily removed from the dental implant by heating. This paper discusses the development of an induction-heating device to remove the dental crown in the new implant system. First, the finite element simulation of electromagnetic and thermal coupling analysis was implemented to obtain the temperature distributions of the target object for various frequencies, input currents, and coil shapes. Based on the simulation results, experiments were conducted by using prototypes, and an induction heating device was developed to remove the dental crown from the implant.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.45 no.5
• /
• pp.44-51
• /
• 2008

UV lamp systems have been used for cleaning of display panels of TFT LCD or Plasma Display Panel (PDP). However, the needs for high efficient cleaning and low cost made high voltage plasma cleaning techniques to be developed and to be improved. Dielectric-Barrier Discharges (DBDs), also referred to as barrier discharges or silent discharges have been exclusively related to ozone generation for a long time. In this paper, a 6kW high voltage plasma power supply system was developed for LCD cleaning. The 3-phase input voltage is rectified and then inverter system is used to make a high frequency pulse train, which is rectified after passing through a high-power transformer. Finally, hi-directional high voltage pulse switching circuits are used to generate the high voltage plasma. Some experimental results showed the usefulness of atmospheric plasma for LCD panel cleaning.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.117-117
• /
• 2009

저항 점 용접 시스템은 SCR 방식과 Inverter 방식으로 나뉘어지는데 현재 공급전원의 안정화 및 고속의 제어가 가능한 Inverter 방식으로 점차 변해가는 추세이다. 이러한 추세에 따라 기존 SCR 방식에서는 구현하기 힘들었던 고속의 전류제어가 요구되고 있으며 여러 제어 알고리즘들이 적용되고 있다. 일반적으로 전류를 제어하기 위해 PI제어 알고리즘이 많이 사용되고 있다. PI제어보다 좀더 반응이 빠르고 정밀한 제어 알고리즘의 적용이 시도되고 있지만 실질적으로 현장에 적용하여 활용하기에 어려움이 있어 PI제어가 많이 선호되고 있다. 일반적으로 용접전류의 제어는 일정한 전류를 공급할 수 있게 하는 것이 주요하지만 저항 점 용접 시스템에서는 일정한 전류의 공급 이외에 목표 전류까지 도달하는 응답시간 또한 주요한 사항으로 작용하고 있다. 이는 짧은 통전시간으로 인해 응답성에 따라 입열량의 차이가 나타나기 때문이다. 응답시간이 느릴수록 그만큼 전류의 공급이 적어지고 이로 인해 입열량이 감소하게 된다. 국내의 Inverter 방식의 경우 응답시간이 15ms 이상이지만, 해외 선진 제품의 경우 10ms 이하의 응답시간을 가져 크게는 1cycle(16.6ms)의 차이가 나고 같은 용접전류 조건에서도 용접성의 차이가 나타나게 된다. 본 연구에서는 응답시간에 따른 용접성의 변화와 응답시간 제어의 필요성을 확인하기 위해 PI제어기를 응답시간에 따라 설계하고 이를 자체 제작한 Inverter DC 저항 점 용접기에 적용하여 용접실험을 실행하였다. 용접소재로는 현 자동차용 강판 소재인 SPFC590, 1mmt를 사용하였고 인장 및 단면시험을 통해 용접성을 비교하였다. 또한 각각의 로브곡선을 도출하고 비교하여 응답시간에 따른 용접성의 차이를 확인하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.10
• /
• pp.5310-5316
• /
• 2013

Maximum Power Point Tracking (MPPT) method for Photovoltaic (PV) system is implemented in PV inveter and it generate the maximum electric power from PV cell. MPPT method has been studied to have high efficiency and high tracking speed. However, these studies are basically focused on the performance under fixed irradiance condition. Based on the typical Perturbation and Observation (P&O) method, this paper presents the research results on modified P&O method to have a better performance under varying irradiance condition. The modified P&O method can have a better performance under varying irradiance condition because the additional measurements during the MPPT control period are conducted. The proposed MPPT method is verified by using 250kW PV inverter under linearly varying irradiance condition according to EN 50530.

• Journal of Korea Society of Industrial Information Systems
• /
• v.21 no.3
• /
• pp.29-33
• /
• 2016

Development of the distributed energy resources such as photovoltaic, wind, and fuel cell has increased rapidly due to the rising demand for clean energy utilization. On the other hand, the distribution system became complex and has problems such as degradation of power factor and current unbalance caused by power converters, reactive power and unbalanced loads. To solve these problems, this paper proposes a 3-phase 4-leg type power conditioning system with compensation control algorithm for the reactive power and unbalance current in distribution system using photovoltaic resource. It is simulated in PSCAD/EMTDC and the effectiveness is confirmed.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.4
• /
• pp.411-419
• /
• 2005

In this paper, a sliding mode observer for solar array current estimation in the photovoltaic power generation system is presented. The solar array current estimation Information is obtained from the sliding mode observer and fed into the maximum power point tracker to update the reference voltage. The parameter values such as inverter dc link capacitances cm be changed up to 50$\%$ from their nominal values and the linear observer can't estimate the correct state values under the parameter variations and noisy environments. The configuration of sliding mode observer is simple, but it shows the robust tracking performance against parameter variations and modeling uncertainties. In this paper, the method for constructing the sliding mode observer using equivalent control input is presented and the convergence of the proposed observer is verified by the Lyapunov method. The mathematical modeling and the experimental results verify the validity of the proposed method.

• The KIPS Transactions:PartA
• /
• v.12A no.6 s.96
• /
• pp.531-538
• /
• 2005

In the high performance Analog Information Processing Systems(AIPS), gain boosting or additional gain stage is required when the gain is not sufficient with one stage amplification. This work shows that high gain is neatly obtained by enhancing the gain using the negative resistance element. Compared to the conventional techniques, the proposed scheme enjoys full output swing, small circuit area and power consumption, and the applications to various configurations of amplifiers. The negative resistance element is placed between the differential output nodes when used in the Op-Amp. The HSPICE simulation indicates that enhancement of more than 40 dB is readily obtained in this simple configuration when the negative resistance element is implemented in the form of cross-coupled CMOS inverters.