• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.20 no.5
• /
• pp.31-37
• /
• 2020

In this paper, we propose a novel sub-wavelength unit cell metamaterial absorber using multi-layer structure. The proposed absorber consists of 4 layers, and each layer has a spiral resonator connected by a via hole. This structure increases inductance of the unit cell, and therefore the resonant frequency can shift to lower frequency. We optimized the proposed absorber, and the electrical size of the unit cell is dramatically reduced to 0.013 times of the wavelength. The performance of the proposed absorber is demonstrated with full-wave simulation and measurement results. An absorption rate exceeding 97% is achieved at 1.74GHz. In addition, the proposed absorber attains a high absorption rate of 90% for different polarization and incident angles.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.4
• /
• pp.368-378
• /
• 2004

In this paper, we proposed the compensation structures for the enhanced directivity of CPW(Coplanar waveguide) directional couplers with finite-extent backed conductor. The proposed compensation structures are. realized by expanding the slot width between signal line and ground plane in center region of couplers. The CPW couplers with expanded slot have the same phase velocity for even and odd mode because of added inductance and changed capacitance appropriately, so the enhanced directivity is accomplished. The designed CPW directional couplers have good directivity and matching characteristic at center frequency in simulation and measurement.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.4
• /
• pp.113-119
• /
• 1989

With optimal inductors shunted at the ends of the waveguide of RF exciting laser, the voltage variation can be reduced dramatically. If multiple inductores are shunted at the appropriate positions, almost the perfect RF uniformity is possible. All the optimum inductances are derived from the unique method of transmission line theory, which illustrates visually the whole variation of standing wave pattern along the hollow waveguide.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.12 s.354
• /
• pp.75-82
• /
• 2006

In this paper, we design the meander line inductors with high sensitivity and high quality factor(Q) using high characteristic impedance of aperture ground plate. Sensitivity as a frequency is new defined by variation of effective inductance per analysis frequency range instead of self resonance frequency (SRF). An equivalent lumped circuit is derived to explain the characteristic of high frequency inductor. The 4 nH meander line inductor with aperture ground plate has 0.45 nH/GHz of good sensitivity and 86 of Q at 0.7 GHz.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.2
• /
• pp.59-64
• /
• 2001

The distribution of current in the conductors influenced by the armature geometry and velocity is an important parameter for determining performance of an electromagnetic launcher(EML). the electric current in the early launching stage tends to flow on the outer surfaces of the conductors, resulting in very high local electric current density. However, the tendency for current to concentrate on the surface is driven by the velocity skin effect later in launching stage. The high current density produces high local heating and, consequently, increases armature wear which causes several defects on EML system. This paper investigates the effects of rail/armature geometry on current density distribution, launcher inductance gradient (L'), and contact force. Three geometrical parameters are used here to characterize the railgun system. These are the ratio of contact length to root length, relative position of contact leading edge to root trailing edge, and the ratio of rail overhang to the rail height. The distribution of current density, L', contact force between various configurations of the armature and the rail are analyzed and compared by using the EMAP3D program.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.2
• /
• pp.1044-1050
• /
• 2014

Maximum torque per ampere vector controller is widely used to control permanent magnet synchronous motors. For the controller to work properly, it is important to know the exact values of motor parameters such as a stator resistance, inductances, and the flux linkage of the permanent magnet. In this paper, an adaptive control algorithm is proposed to estimate these parameters using MRAS(Model Reference Adaptive System). Simulation results demonstrate the effectiveness of the proposed algorithm.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.6
• /
• pp.522-525
• /
• 2009

We investigated the fault current characteristics of the separates three-phase flux-lock type superconducting fault current limiter(SFCL) according to the variation of inductances. The single-phase flux-lock type SFCL consists of two coils. The primary coil is wound in parallel to the secondary coil on an iron core. And superconductor is series connected on secondary coil. Superconductor is using the YBCO coated conductor. The separated three-phase flux-lock type SFCL consists of single-phase flux-phase type SFCL in each phase. To analyze the current limiting characteristics of a three-phase flux-lock type SFCL, the short circuit experiments were carried out fault such as the triple line-to-ground fault. The experimental result shows that fault current limiting characteristics of additive polarity winding was better than subtractive polarity winding and when the inductances of coil 2 was lower, resistances of YBCO CC was more generated.

• Journal of the Korean Vacuum Society
• /
• v.15 no.4
• /
• pp.380-386
• /
• 2006

In this study, we had designed and fabricated the plasma focus device which can generate the light source for EUV(Extreme Ultra Violet) lithography. And we also have investigated the basic electrical characteristics of currents, voltages, resistance and inductance of this system. Voltage and current signals were measured by C-dot and B-dot probe, respectively. We applied various voltages of 1.5, 2, 2.5 and 3 kV to the anode electrode and observed voltages and current signals in accordance with various Ar pressures of 1 mTorr to 100 Torr in diode chamber. It is observed that the peak values of voltage and current signals were measured at 300 mTorr, where the inductance and impedance were also estimated to be 73 nH and $35 m{\Omega}$ respectively. The electron temperature has been shown to be 13000 K at the diode voltage of 2.5 kV and this gas pressure of 300 mTorr. It is also found that the ion density Ni and ionization rate 0 have been shown to be $N_i = 8.25{\times}10^{15}/cc$ and ${\delta}$= 77.8%, respectively by optical emission spectroscopy from assumption of local thermodynamic equilibrium(LTE) plasma.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.4
• /
• pp.316-329
• /
• 2012

In this paper, optimum design process of ICP (Inductively Coupled Plasma) torch, which has been used widely in aerospace application, such as supersonic plasma wind tunnel, is presented. For this purpose, the behaviors of equivalent circuit parameters (equivalent resistance and inductance, coupling efficiency) were investigated according to the variations of torch design parameters (frequency, $f$, confinement tube radius, $R$ and coil turn numbers, $N$) in the basis of analytical and numerical MHD (Magneto Hydro-Dynamics) models combined with electrical circuit theory. From the results, it is found that equivalent resistance is increased with the increase of $f$ values but vice versa for equivalent inductance. For elevated values of $R$ and $N$, however, both parameters tend to increase. Based on these observations, ICP torch with a power level of 10 kW can be optimized at the design ranges of $f$=4~6 MHz, $R$=17~25 mm and $N$=3~4 to maximize the electrical coupling efficiency, which is the ratio of equivalent resistance to equivalent inductance.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.230-230
• /
• 2007

전력선 통신(Power Line Communication)은 최근 전력선을 이용한 통신기술의 발달과 더불어 세계적으로 관심도가 높아지고 연구 개발 및 자본 투자가 활발히 진행되고 있으며, 안정적인 네트워크를 구성하기 위해서는 고주파 전력선 통신 신호를 차단하는 블로킹 필터가 반드시 적용되어야 한다. 전력선 통신용 블로킹 필터는 광대역의 주파수 특성과 높은 신호감쇄 특성 및 대전류 특성이 요구되며, 이러한 특성을 구현하기 위해서는 블로킹 필터의 핵심부품인 자심재료의 고투자율 및 대전류화가 이루어져야 한다. 따라서 본 연구에서는 우수한 전 자기적 특성이 균일하게 유지되고, 전력선에 흐르는 대전류에 의한 자심재료의 포화가 발생하지 않도륵 새로운 자심 재료를 설계하여, 전력선 통신을 적용한 홈 네트워크 구축의 핵심 부품인 광대역 블로킹 필터를 개발하고자 하였다. 2350과 0.3 T의 투자율과 포화자속 밀도를 갖는 EI 형상의 자심재료를 해석모델로 설정하고 다중 에어 갭의 위치에 따른 전류와 자속밀도 변화를 유한요소 해석법으로 분석한 결과 자심재료의 대전류 특성에 지배적인 영향을 미치는 에어 캡의 삽입 위치를 알 수 있었고, 새로운 해석 모델인 I 형상의 로드(ROD) 코어에 대해 수치해석을 수행하여, 100A의 통전 전류에서도 자기적으로 포화되지 않고 인덕턴스의 정밀 제어가 가능하고, 특성의 신뢰성과 대전류에 대한 안정성을 증가시킬 수 있는 인덕터를 설계하였다. 또한 수동소자를 이용한 LC 공진회로를 기본 구성으로 하고, 주파수 대역, 신호 감쇄율과 대전류 특성, 상용화를 고려하여 블로킹 필터 회로를 설계하였으며, 유한요소해석법을 적용한 전자장 모의해석을 통하여 최소의 크기를 갖는 I 형상의 자심재료에 $6{\Phi}$의 에나멜 동선을 6.5턴, 6턴 권선하여 2.5, $2.15\;{\mu}H$의 인덕턴스를 갖는 직렬 인덕터를 구현하였고 블로킹 필터를 구성하였다. 주파수에 따른 신호감쇄 특성을 5 Hz~1 MHz의 주파수 범위에서 측정한 결과 약 490 kHz~450 kHz의 주파수 대역에서 -70dB의 신호감쇄 특성을 나타냈다. 본 연구를 통해 개발된 100A급 광대역 블로킹 필터가 적용되어 상용화 될 수 있을 것으로 판단되며, 또한 모뎀 통신 주파수 대역에서 -70dB 이상의 높은 감쇄 특성을 갖기 때문에 신호차단 특성이 보다 우수할 것으로 사료된다.