• Journal of Korean Society of Steel Construction
• /
• v.27 no.3
• /
• pp.333-345
• /
• 2015

This study evaluated the static and dynamic shear strength of cast-in-place anchors reinforced with hairpin bars in uncracked and cracked concrete. The anchors 30mm in diameter reinforced with D10 hairpin bar were designed with an edge distance of 150mm and an embedment depth of 240mm. The cracked specimens consisted of the orthogonal and parallel cracks to the direction of shear loads, respectively. The dynamic strength was evaluated using seismic qualification tests based on the ACI 355.2 standard. The shear strength of the hairpin reinforced anchor was hardly correlated to the concrete cracks and the dynamic strength was similar to its static shear strength. Finally, a consideration on the design strength of hairpin reinforced anchors was presented.

• Journal of Korean Association for Spatial Structures
• /
• v.9 no.3
• /
• pp.93-100
• /
• 2009

As interest in latest cultural heritance is increased, an importance about conservation of dilapidated cultural building asset is risen. Most of cultural building asset used wood by main material and conservation repair about corrosion and damage by deterioration of these cultural building asset considers cultural value of member and the basis principle is the archetype maintenance. Accordingly, conservation processing method that use synthetic is embossed. This paper experimented with reinforcement sectional area ratio, direction of section, length, strength of synthetic resins as variable and manufactures total 14 specimens as experimental study about compression reinforcement performance of circular section wood that strengthen by synthetic resins. The result of this paper has shown that adequate strengthen is more efficient than new member and the most important authenticity in strengthen and repair of cultural heritance can be ensured.

• Journal of the KSME
• /
• v.31 no.3
• /
• pp.293-299
• /
• 1991

단섬유보강 금속복합재료의 2차가공은 금속복합재료의 넓은 범위 응용을 위해 필히 요구된다. 여러 가공방법 중 하나인 열간압출시 보강섬유파괴 및 계면에서의 접합분리 및 균열발생이 없는 제조공정의 최적화를 위해서 가공시 내부조직의 소성변형 기구 규명보다 압출력에 의한 응력분 포와 기지재료와 보강섬유 사이 계면 변화 및 기계적 특성 관계규명이 정량적으로 요구된다. 본 글에서는 유한요소법을 이용하여 계면에서의 접합상태를 임의로 가정하여 압출조건에 따른 압 출후의 보강섬유 방향 및 계면균열 및 접합분리를 거시적으로 예측하고, advanced shear-lag을 이용하여 균열 전, 후의 응력. 변형관계를 미시적으로 규명할 수 있음을 제시하였다. 그러나 향후 현상적 모델인 shear-lag 모델을 수학적 모델인 균질화법에 도입하면 미시적. 거시적 거 동해석이 함께 요구되는 금속복합재료의 열간압출거동 해석을 일체적으로 행할 수 있어 효율적 이고 정확한 예측이 가능하리라고 사료된다.

• Proceedings of the KAIS Fall Conference
• /
• 2011.12b
• /
• pp.465-468
• /
• 2011

압축을 받는 판 구조의 경제적인 단면 보강을 위해 종방향 보강재인 U형 단면 리브를 적용하는 것이 효과적이나, 현재 국내에서는 명확한 설계지침이나 연구자료가 제시되지 못하고 있다. 따라서 U리브의 적정 크기 및 최적 간격에 대해 검토 후 이에 관한 지침이 제시될 필요성이 있다. 이에, 본 연구에서는 U리브의 단면 크기 및 강성에 따른 탄성좌굴강도 및 좌굴모드의 변화를 알아보고자 한다. 유한요소해석 프로그램인 ABAQUS를 이용하여 고유치 해석을 실시하였고, 이론값과 해석적 결과의 탄성좌굴강도를 비교하였다. 이러한 분석 결과를 토대로 향후 U리브의 최소소요강성 및 단면 선정방안을 제시하는데 기여할 수 있을 것으로 기대된다.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.622-640
• /
• 2009

원유 비축기지 저장공동과 같이 상하로 긴 형상의 대규모 공동에서 횡방향의 지압이 과도하게 작용하면 천정부의 응력집중과 측벽의 암반 변위가 과도하게 발생하여 저장공동의 불안정 요인이 된다. 특히 지압의 절대 크기가 암반 강도의 일정 비율 이상이 되면 응력 집중에 의한 암반의 취성 파괴를 유발하고, 이러한 현상은 터널 굴착 시 발생하는 파괴음(popping)과, 굴착면에 평행한 형태로 암편이 탈락하는 취성파괴(spalling) 현상을 동반한다. 이 글에서는 대규모 지하저장공동 굴착시 실제 발생한 과지압으로 인한 문제 사례에 대해 소개한다. 저장공동 굴착시 관찰된 암편 및 숏크리트 탈락과 균열 발생 현상을 관찰하고 암반 계측결과 분석을 통해 과지압의 현상을 진단하였다. 과지압 구간의 현재 상태 및 원안 설계안에 대해 연속체 및 불연속체 안정성 해석을 실시하여 문제의 심각성을 평가하였다. 이를 통해 굴착 형상 변경 및 특수 보강 방안을 제안하였으며 제안된 안의 보강효과에 대한 수치해석 평가 결과를 재검토 하였다. 이들 결과를 종합하여 과지압구간 보강안을 도출하였으며 상시 안정성 감시 대책으로 현장 암반의 미소파괴음 계측 방안을 제시하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.2
• /
• pp.949-954
• /
• 2013

Generally, structural plates under axial compression should be stiffened by longitudinal stiffeners in order to enhance the buckling strength. Though U-shaped ribs would be more efficient for the stiffened plate system, there is in the absence of a proper design guides or relevant research results. Thus this study is aimed to examine the local buckling behavior of stiffened plates with U-section ribs. 3-dimensional analysis models which include 3 types of U-shaped longitudinal stiffeners were simulated by using the finite element code ABAQUS. The bifurcation analysis were conducted and then the buckling analysis results are compared with the theoretical equation values. It is found that the rotational constraint effect provided by the U-ribs should increase the local buckling strength. Some features drawn from a series of parametric study results are summarized.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.1
• /
• pp.16-24
• /
• 2021

This experimental study was conducted to evaluate the in-plane and out-of-plane seismic performances of an unreinforced masonry walls (URMs) strengthened with prestressed steel-bar truss systems developed in the present investigation. The truss systems were installed on both faces of the walls. All the wall specimens were subjected to lateral in-plane or out-of-plane cyclic loads at the fixed gravity stress of 0.25 MPa. The seismic performance of the strengthened specimens was compared to that measured in the counterpart URM. When compared with the lateral load-displacement curve of the URM, the strengthened walls exhibited the following improvements: 190% for initial stiffness, 180% for peak strength, 610% for accumulated energy dissipation capacity, and 510% for equivalent damping ratio under the in-plane state; the corresponding improvements under the out-of-plane state were 230% for initial stiffness, 190% for peak strength, 240% for accumulated energy dissipation capacity, and 120% for equivalent damping ratio, respectively. These results indicate that the developed technique is very promising in enhancing the overall seismic performance of URM.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.28 no.4
• /
• pp.13-20
• /
• 2024

In this study, when subjected to in-plane shear such as a shear wall, the behavior characteristics of a concrete member using CFRP rebars were investigated when the longitudinal reinforcement ratio was kept constant at 2.96% and the transverse reinforcement ratio was changed from 0.30 to 2.98%. The evaluation was conducted based on MCFT theory and analyzed by comparison with the case of concrete members using steel rebars. When the reinforcement ratio ranged from 0.30 to 1.19%, concrete members employing CFRP rebars exhibited higher shear strength compared to those using steel rebars. In contrast, at high reinforcement ratios of 1.79 and 2.98%, it was observed that the shear strength of the member with CFRP rebar was lower compared to the member with steel rebar. Maximum shear strain was observed to be higher for members reinforced with steel rebars at lower reinforcing bar ratios, while for ratios of 0.97% and above, CFRP rebars resulted in higher maximum shear strain. As the reinforcement ratio increases, the use of CFRP rebar instead of steel rebar results in a greater increase in maximum shear strain. By analyzing the difference in strain in the reinforcing bar as well as the difference in principal strain in the element caused by differences in the mechanical properties of the steel rebar and CFRP rebar, the shear strength and shear strain when using steel rebar and CFRP rebar with different reinforcement ratios can be compared and analyzed.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.14 no.1
• /
• pp.63-70
• /
• 2010

The purpose of this study is to investigate experimentally the behavior of unreinforced masonry RC frames strengthened by CFRP sheet under cyclic lateral loading. Four test specimens were constructed as one-story, one-bay, 1/2 scale unreinforced masonry infilled RC frames and differences in strength and stiffness were evaluated in specimens on which had been applied different retrofitting methods. Test results indicated that the CFRP sheets significantly increased the strength and stiffness of the specimens, and the specimens retrofitted in columns and masonry indicated the most adequate retrofitting methods.

• Journal of the Korea Concrete Institute
• /
• v.28 no.5
• /
• pp.581-592
• /
• 2016

Tensile constitutive stress-strain model of steel fiber reinforced concrete (SFRC) in fib MC2010 was investigated. In order to model tensile behavior of SFRC, three point loading flexural tests were conducted on notched small beams according to BE-EN-14651. Design parameters for the constitutive model were determined from the flexural tests. Flexural test and finite element analysis were conducted on large SFRC beam without steel reinforcements and compared with each other. In addition, parametric study on the effect of compressive and tensile model, and characteristic length on flexural behavior of the SFRC beam was conducted also. In results, pre-peak load-displacement curves from the FE analysis was close to experimental curves but significant difference was shown in post-peak behavior. The reason of the difference is originated from the fact that the fiber distribution and orientation were not being properly considered in the MC2010 model. This study shows that modification and detail explanations on the orientation factor K in MC2010 might require to better reproduce the behaviour of large scale SFRC beams.