• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.4
• /
• pp.420-430
• /
• 2005

This study was performed to change the hydrophilic $NH_4Y$-zeolite to the hydrophobic one for removal of VOCs by removing the $Al^{3+}$ in the zeolite-structure to increase the Si/Al ratio, for which the three pelleted $NH_4Y$-zeolite samples were contacted separately with the steam of $400^{\circ}C$, $500^{\circ}C$ and $600^{\circ}C$, respectively, in a stainless steel column for 4 hours. Then extraction of the ex-structure aluminum of the hydrolyzed zeolites with the nitric acids of 0.25, 0.50, 0.75, and 0.10 M at $90^{\circ}C$ in 500 mL-flasks, respectively, according to steam temperature were followed. XRD analysises of the dealuminated zeolites showed that the peaks of the zeolites that had been hydrolyzed with the steams of both $500^{\circ}C$ and $600^{\circ}C$ are distorted more with the increase of the concentration of nitric acid used for extraction of the ex-structure aluminums, however, those hydrolyzed with steam of $400^{\circ}C$ became amorphous phase when treated with the all nitric acids of four concentrations. Also the EDX analysises showed that the BET surface areas and TPVS of the zeolites that had been hydrolyzed with the steam of $600^{\circ}C$ were increased with the concentration of the nitric acid when the nitric acids of 0.25 M and 0.5 M had been used but decreased when the nitric acids of 0.75 M and 1.0 M had been used. These results led to the conclusion that both the $600^{\circ}C$ and $500^{\circ}C$-steam and the 0.5 M-nitric acid are appropriate to change the hydrophilic $NH_4Y$-zeolites to the hydrophobic one, which were proven by the measurement of the benzene and tolune-adsorbing capacities showing the same trend as the BET surface area and TPV The Si/Al ratios and water-adsorbing capacities of the dealuminated zeolites were increased and decreased, respectively, with the concentration of the nitric acids so that it showed that the hydrophobicity is increased.

• Applied Chemistry for Engineering
• /
• v.22 no.4
• /
• pp.423-428
• /
• 2011

Hydration characteristics of cement containing zeolite mined at Daepo in Gyeongbuk province were studied for use as a mineral admixture. The cement paste containing zeolite was characterized by the measurement of heat evolution, XRD, EDS, nitrogen adsorption and mercury intrusion porosimetry. The cement paste containing zeolite exhibited tendencies toward acceleration of paste setting and promotion of cement hydration with the increase of zeolite content. The flow of mortar containing zeolite strongly reduced with increase of zeolite content. Compressive strength of the mortar containing zeolite increased very rapidly at an early age in comparison with plain mortar. These results would be related to aluminum species escaped from zeolite particles during the alkali dealumination of zeolite by the hydration process of cement.

• Journal of the Mineralogical Society of Korea
• /
• v.13 no.1
• /
• pp.1-14
• /
• 2000

알루나이트는 포항지역의 제3기 연일층군의 이암 층내의 탄산염 결핵체 주변에서 할로이사이트와 함께 극미립 변질물 (1-2 $\mu\textrm{m}$)로서 산출된다. 알루나이트는 정육면체와 유사한 능면체 결정형을 이루고 침상 내지 단주상의 할로이사이트와 밀접한 공생관계를 이룬다. X-선회절 분석에 의해서 이 알루나이트는 a=6.9897(1) $\AA$, c=17.2327(4)$\AA$, V=728.75(3) $\AA$3의 격자상수값을 갖는 것으로 밝혀졌다. X-선형광된 이 알루나이트의 화학식은 (K0.94N0.06)(Al2.55Fe3+0.45)(SO4)2(OH)6 으로서, 나트로알루나이트 단성분을 6-7 mole%정도 함유하는 것으로 분석되었다. 또한 시차열분석 (TG-DTG-DTA)을 통해서 알루나이트의 승화성 성분들 (H2O와 SO3)의 존재와 함유 정도를 조사하였고, 고온X-선회절분석을 병행하여 이 광물의 OH기의 이탈 반응 (52$0^{\circ}C$)과 고온상으로의 전이 반응 ($600^{\circ}C$ 및 $700^{\circ}C$)을 감정 하였다. K/Ar 법으로 측정된 알루나이트의 생성 연대 ($0.342\pm$0.008 Ma)와 안정동위원소들의 분석 결과 ($\delta$18Oso4=-1.7, $\delta$DSMOW=-31, $\delta$34S=-10.8)는 이 알루미늄 황산염 광물이 연일충군의 융기 이후에 야기된 민물의 유입에 의한 표성기원의 변질작용의 결과로 생성되었음을 지시한다. 알루나이트+할로이사이트 공생군의 침전은 이암 내에서 조성된 강산성 (pH=2-3)의 알루미늄 황산염 용액이 탄산염 결핵체를 만나 반응하여 pH가 국지적으로 증가되어 (pH=4) 과포화되는 과정에 의해서 야기되었다. 컴퓨터를 이용한 Al3+의 포화지수에 관한 화학적 평형 모델링 실험 결과, 알루미늄 황산염 용액으로부터의 알루나이트와 할로이사이트의 침전은 pH=4 및 \ulcornerSO42-=10-4M 조건에서 K+과 Si(OH)4의 농도가 10-4M 이상 유지되어야 가능한 것으로 밝혀졌다.

• Journal of the Korean Chemical Society
• /
• v.39 no.8
• /
• pp.627-634
• /
• 1995

Layered double hydroxides ($Mg-Al-CO_3$ systems, LDH), which are hydrotalcite-like anionic clay minerals, having different $Mg^{2+}\;to\;Al^{3+}$ ratio were synthesized by coprecipitation method. The subsequent products were characterized by the following methods; elemental analysis, X-ray powder diffraction, thermal analysis (DSC and TGA), FT-IR and $^{27}$Al-MAS NMR. X-ray powder patterns showed that the products formed were layered structure materials. Two heat absorption peaks were observed around 20 ∼280$^{\circ}C$ (surface water and interlayer water) and 280∼500$^{\circ}C$ (water from lattice hydroxide and carbon dioxide from interlayer carbonate) in DSC diagrams, and they were quantitatively analyzed by TGA diagrams (in case LDH4 16.2% and 28.6% respectively). FT-IR spectra indicate that the interlayer carbonate ions occupied symmetrical sites between two adjacent layers in a parallel direction. $^{27}$Al-MAS NMR spectra show only single resonance (8.6 ppm) of the octahedrally coordinated aluminum similar magnesium. When LDH4 was calcined at 560$^{\circ}C$ for 3 hours in air, its layered structure was destroyed giving a mixed metal oxide. However it readily became rehydrated in aqueous chromate solution to its original structure.

• Journal of the Korean Magnetics Society
• /
• v.25 no.3
• /
• pp.83-86
• /
• 2015

Nowadays the weapon systems are employed air bursting munition (ABM) as smart programmable 40 mm shells which have been developed in order to hit the target with programmed munition that can be air burst after a set distance in the battlefield. In order to improve the accuracy of such a bursting time, by measuring the speed of the munition from the barrel, weapon systems calculate the exact time of flight to the target and then the time information must be inputted to the munition. In this study, we introduce a device capable of detecting a shot at K4 40 mm automatic grenade. The shot is composed of a rotating copper band to convert linear motion into rotary motion when it passes through the barrel, the steel section is exert the effect of fragment and aluminum section to give fuze information. The aluminum section was used to detect munition using eddy current method. To measure muzzle velocity by means of non-contact method, two eddy current probes separated 10 cm was employed. Time interval between two eddy current probe detection times was used as muzzle velocity. The eddy current probe was fabricated U-shape Mn-Zn ferrite core with enamelled copper wire, and 200 kHz alternating current was used to detect inductance change. Measured muzzle velocity using the developed sensor was compared to the Doppler radar system. The difference was smaller than 1%.

• Journal of Welding and Joining
• /
• v.15 no.4
• /
• pp.109-115
• /
• 1997

Laser cladding is a technique for modification of metal surface. In this laser cladding experiment a metal powder feeding system was developed for more efficient laser cladding. This system can reduce processing time and be used simpler than the conventional method. The feeding of metal powder has given a rise to the process for sequential buildup of bulk rapidly solidified materials in the form of fine powder stream to the laser cladding process. The parameters of laser cladding have been investigated using this experimental equipment. Bronze on aluminum alloy and copper on aluminum alloy were experimented by using defocused beam, powder feeding system, and gas shielding. Good cladding was achieved in the range of beam travel speed of 2.25m/min. In the case of copper/aluminum and bronze/aluminum substrate, the absorption of laser beam was too high to produce low diluted clad. In the case of copper/1050 aluminum, the optimal laser cladding condition was of laser power of 2.8kW, powder feed rate of 0.31g/s and beam travel speed of 2.25m/min. In the case of bronze/aluminum the optimal condition is of laser power of 2.5kW, powder feed rate of 0.31g/s, and beam travel speed of 2.36m/min.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.8
• /
• pp.5406-5411
• /
• 2014

Car emblems are representative of both the car and driver. Each emblem had its own distinct history and meaning. Today, customers and car designers require high quality car emblems. Today's car emblems are made of plastic, metal, steel, and aluminum. The emblems need to represent the designer's creative idea and symbol of car. On the other hand, the development period of an emblem requires a minimum of 6 months. When the design of an emblem is changed, more time is required. The paradigm shift of a car emblem changes from analog to digital. In this research, a digital LCD emblem system and the method of attaching it to the airbag cover were developed. When the airbag is engaged, digital LCD emblem system is not separated from the airbag.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.2
• /
• pp.733-738
• /
• 2021

Recently, people's interest in marine leisure has been increasing, and research and development on leisure boats are actively being carried out to pioneer overseas markets. These days, the materials used for leisure boats are fiber-reinforced plastic (FRP) and aluminum alloy. However, FRP is hygroscopic and causes environmental problems, and aluminum alloy has high thermal conductivity and fire susceptibility. Therefore, titanium alloy is being adopted as a material for leisure boats instead. In this study, hull thicknesses and design pressures were calculated while considering dynamic effects for titanium boats. Four sets of rules and regulations were used: ISO 12215-5, RINA Pleasure Yacht, LR Special Service Craft, and KR High-speed Light Craft. The maximum bottom slamming loads were in the order of ISO, KR, LR, and RINA, and the required hull thicknesses were in the same order. This research might be helpful for understanding the rules, regulations, and overseas export of leisure boats.

• Elastomers and Composites
• /
• v.46 no.4
• /
• pp.284-289
• /
• 2011

Prismatic reflective sheets were prepared using microprisms, and their retroreflection and structural properties were investigated and compared with encapsulated lens type reflective sheets based on glass beads. As prepared, the prismatic reflective sheets show well arranged array of microprisms. The arrangement of glass beads in encapsulated lens type reflective sheets is also found to be uniform without any cracks. However, during the coating process of the PET layer, the beads are coming out and the gaps are formed due to the application of high pressure. Even though the preparation method for reflective sheets based on microprisms is similar to that of reflective sheets based on glass beads, the method is relatively simple and cost effective, and also needs less time. Prismatic reflective sheets show higher coefficient of retroreflection from all entrance angles compared to reflective sheets based on glass beads. The results prove that the prismatic reflective sheets can be used for preparing the traffic sign boards to secure a clear view.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2002.11b
• /
• pp.1547-1550
• /
• 2002

MANET은 전형적인 무선 네트워킹과는 다른 새로운 무선 네트워킹 파라다임으로써 기존 유선 망의 하부 구조에 의존하지 않고 이동 호스트틀로만 구성된 네트워크이다. Ad Hoc망에서 통신을 하기 위해서는 출발지 노드에서 목적지 노드까지 데이터 전송을 위한 라우팅에 관한 문제이다. Ad Hoc망에서는 모든 단말기의 위치변화가 가능하기 때문에 경로설정에 어려움이 따른다. 노드간에 정보를 보내고자 할 때 노트가 인접한 상태가 아니면 정보를 직전 보낼 수 없고 여러 중간 노드들을 거쳐서 정보를 보내는 다중-홉 라우팅 방식을 사용해야 한다. 따라서 중간 노드들은 패킷 라우터의 역할을 해야하는데 무선 통신 자체가 좁은 대역폭과 한정된 채널을 가지고 전송 범위가 제한되는 문제가 있다. 또한 노트 자체의 이동성과 전력 소모 등으로 인한 이탈은 망 위상을 수시로 변화시키므로 노트간에 정보를 전송하는데 가장 종은 경로는 수시로 변경될 수 있으므로 많은 어려움이 따르게 된다. 본 논문에서는 이러한 문제의 해결방안으로 경로유지 과정에서 Ad Hoc망 내의 노드들은 이동성의 특성으로 인해 현재 사용되는 경로 보다 더 짧고 효율적인 경로가 발생하고 중간 노트가 이동 될 때 새로운 경로로 갱신하여 솔기없는 최적의 경로를 유지할 수 있는 방법을 제안한다. 제안 방법은 ZRP의 IERP에서 감청모드를 통하여 사공중인 경로보다 최적의 경로를 감지하여 새로운 경로로 갱신하는 방법과 중간 노드가 이동하여 경로가 깨진 경우 부분적으로 경로를 복구하는 방법을 제시하여 항상 최적화된 경로를 유지함으로써 Ad Hoc망의 위상변화에 대한 적응성을 높일 수 있도록 한다. SQL Server 2000 그리고 LSF를 이용하였다. 그리고 구현 환경과 구성요소에 대한 수행 화면을 보였다.ool)을 사용하더라도 단순 다중 쓰레드 모델보다 더 많은 수의 클라이언트를 수용할 수 있는 장점이 있다. 이러한 결과를 바탕으로 본 연구팀에서 수행중인 MoIM-Messge서버의 네트워크 모듈로 다중 쓰레드 소켓폴링 모델을 적용하였다.n rate compared with conventional face recognition algorithms. 아니라 실내에서도 발생하고 있었다. 정량한 8개 화합물 각각과 총 휘발성 유기화합물의 스피어만 상관계수는 벤젠을 제외하고는 모두 유의하였다. 이중 톨루엔과 크실렌은 총 휘발성 유기화합물과 좋은 상관성 (톨루엔 0.76, 크실렌, 0.87)을 나타내었다. 이 연구는 톨루엔과 크실렌이 총 휘발성 유기화합물의 좋은 지표를 사용될 있고, 톨루엔, 에틸벤젠, 크실렌 등 많은 휘발성 유기화합물의 발생원은 실외뿐 아니라 실내에도 있음을 나타내고 있다.>10)의 $[^{18}F]F_2$를 얻었다. 결론: $^{18}O(p,n)^{18}F$ 핵반응을 이용하여 친전자성 방사성동위원소 $[^{18}F]F_2$를 생산하였다. 표적 챔버는 알루미늄으로 제작하였으며 본 연구에서 연구된 $[^{18}F]F_2$가스는 친핵성 치환반응으로 방사성동위원소를 도입하기 어려운 다양한 방사성의 약품개발에 유용하게 이용될 수 있을 것이다.었으나 움직임 보정 후 영상을 이용하여 비교한 경우, 결합능 변화가 선조체 영역에서 국한되어 나타나며 그 유