• Korean Chemical Engineering Research
• /
• v.47 no.6
• /
• pp.740-746
• /
• 2009

In the present study, the drowning-out crystallization of L(+)-calcium lactate was investigated in order to develop the crystallization separation process. The crystallization of the calcium lactate was induced by injecting the alcoholic anti-solvent into the aqueous solution of calcium lactate and the control of the calcium lactate crystal size during the crystallization was primarily investigated under the consideration of the anti-solvent species, anti-solvent composition and agitation speed as the key operating factors. Alcohols of methanol, ethanol, n-propanol and i-propanol were used as the anti-solvent for the drowning-out crystallization. Prior to the crystallization experiment, the solubility of calcium lactate in the water-alcohol mixture was measured along with the variation of the alcohol species and composition, which was necessary to estimate the supersaturation level of the crystallization. By the drowning-out crystallization, the calcium lactate crystals of the fabric shape were obtained. Using the ethanol as the antisolvent, the fabric crystals close to the needle shape were produced. However, the hairy crystals were obtained by using the propanol as the anti-solvent. Due to such morphological features, the crystals was highly apt to form the aggregates. The aggregation of the crystals was intensified as increasing the alcohol fraction in the water-alcohol mixture. Meanwhile, the agitation caused the breakage of crystals, resulting in the decrease of the crystal size. Therefore, the crystal size in the crystallization was predominantly determined by the competition between the crystal aggregation and breakage.

• Proceedings of the Korean Society for Food Science of Animal Resources Conference
• /
• 2005.05a
• /
• pp.317-321
• /
• 2005

본 연구결과, 콜레스테롤 제거 크림치즈를 만들기 위한 유지방 함량 36%의 크림의 콜레스테롤 제거 최적 조건은 adipic acid로 가교시킨 ${\beta}-CD$ 첨가량 10%, 교반온도 $20^{\circ}C$, 교반시간 30분, 교반속도 800rpm 이었으며, 이 때 콜레스테롤 제거율은 평균 91.42%로 나타났다. 가교화 ${\beta}-CD$ 처리 크림치즈의 관능검사 결과, 가교화 ${\beta}-CD$ 처리 크림치즈는 control과 powder ${\beta}-CD$ 처리한 크림치즈에 비해 저장 기간 동안 쓴맛의 증가가 거의 없었고, 빵에 발리는 정도도 매우 우수하였으며, 전체적인 기호도 또한 높았다. short-chain fatty acid의 경우 저장 기간이 지남에 따라 가교화 ${\beta}-CD$ 처리 크림치즈는 control과 powder ${\beta}-CD$ 처리한 크림치즈에 비해 저급 지방산 생성에 변화가 거의 없었다. 조직검사에서 가교화 ${\beta}-CD$ 처리 크림치즈는 저장 기간 동안 control에 비해 응집성, 탄력성, 점착성의 변화가 없으며 그 수치가 높게 평가되었다. 또한 가교화 ${\beta}-CD$의 재활용률은 97.82%로 매우 높게 나타났다. 위 실험 결과에 따르면, 가교화 ${\beta}-CD$는 콜레스테롤 제거율이 높으며, 제품에 적용 시 품질이 향상될 뿐만 아니라, 재활용률도 높아 이를 유가공 산업에 다양하게 활용이 가능할 것으로 기대된다.

• Applied Chemistry for Engineering
• /
• v.10 no.4
• /
• pp.509-514
• /
• 1999

In Preparing $BaTiO_3$ powder under hydrothermal conditions, effects of reaction period feedstock concentration and mixing rate on crystallinity, mean size and size distribution of particles were studied. Experimental results showed that the particle size became smaller with its narrow distribution as the reaction period and mixing rate increased, but feedstock concentration decreased in contrast with the results based on the classical nucleation-growth model. From these results, $BaTiO_3$ particles seem to be prepared hydrothermally through a multiple reaction procedure that includes dissolution, precipitation, hydrolysis-condensation, aggregation, diffusion and transformation.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1997.10a
• /
• pp.21-25
• /
• 1997

우수한 세라믹스 제조를 위해서는 작은 입자지름, 좁은 입도분포, 구형의 입자형태, dopant와 matrix가 균일한 고용체를 갖고, 응집입자가 없으며 고순도인 원료 분말의 제조가 선행되어야 한다. 이를 위하여 본 연구에서는 수열 합성법을 이용하여$\alpha$-Al$_2$O$_3$, $\alpha$-SiO$_2$, PZT, PSZT, BTO등의 미세분말을 제조하는 공정에서 반응온도, 광화제의 양과 종류, 반응시간, 출발물질의 양과 종류, 전처리공정, 교반공정 등이 평균입자지름과 결정성 및 입도분포에 미치는 영향을 조사하였다. 그결과 미세분말의 종류에 관계없이 반응온도, 반응시간, 성장기질의 농도, 종자결정의 농도 등이 증가할수록 평균입경은 커지며, 광화제의 농도가 증가할수록 평균 입자지름이 작아지고, 광화제의 농도가 종자결정의 농도가 증가할수록 입도분포가 좁아짐을 알 수 있었다. 특히 $\alpha$-SiO$_2$에 대해 수열합성실험으로부터 평균입자지름과 수열합성의 조업변수간의 특성방정식을 얻었다.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.33 no.5
• /
• pp.448-454
• /
• 2000

This study was to examine the physicochemical characteristics of coagulation reaction between ignited oyster shell powder (IOSP) and red tide organisms (RTO), and its feasibility, in developing a technology for the removal of RTO bloom in coastal sea,IOSP was made from oyster shell and its physicochemical characteristics were examined for particle size distribution, surface characteristic by scanning electron microscope, zeta potential, and alkalinity and pH variations in sea water. Two kinds of RTO that were used in this study, Cylindrotheca closterium and Skeletonema costatum, were sampled in Masan bay and were cultured in laboratory. Coagulation experiments were conducted using various c(Incentrations of IOSP, RTO, and a jar tester. The supernatant and RTO culture solution were analyzed for pH, alkalinity, RTO cell number, IOSP showed positive zeta potentials of $11.1{\~}50.1\;mV\;at\;pH\;6.2{\~}12.7$, A positive zeta potential of IOSP slowly decreased with decreasing pNa 4,0 to 2,0. When pNa reached zero, the zeta potential approached zero, When a pMg value was decreased, the positive zeta potential of IOSP increased until pMg 3.0 and decreased below pMg 3.0. IOSP showed 4.8 mV of positive zeta potential while RTO showed -9.2 mV of negative zeta potential in sea water. A positive-negative EDL (electrical double-layer) interaction occurred between $Mg(OH)_2$ adsorption layer of IOSP and RTO in sea water so that EDL attractive force always worked between them. Hence, their coagulation reaction occurred at primary minimum on which an extreme attractive force acted because of charge neutralization by $Mg(OH)_2$ adsorption layer of IOSP. As a result, the coagulation reaction was rapidly processed and was irreversible according to DLVO (Deriaguin-Landau-Verwey-Overbeek) theory. Removal rates of RTO were exponentially increased with increasing both IOSP concentration and G-value. The removal rates were steeply increased until 50 mg/l of IOSP and reached $100{\%}\;at\;400\;mg/l$ of IOSP. Removal rates of RTO were $70.5,\;70.5,\;81.7,\;85.3{\%}$ for G-values of $1,\;6,\;29,\;139\;sec^(-1)$at IOSP 100 mg/l, respectively. This indicated that mixing (i.e., collision among particles) was very important for a coagulation reaction.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.8
• /
• pp.641-648
• /
• 2009

The study presents sewage sludge flotation and thickening efficiencies which changes chemical conditioning and mixing conditions using a flotation thickening system with a microbubble generating pump. Flotation and thickening of sewage sludge are shown to significantly influence kinds of coagulants more than Gt values. It is found that the flotation and thickening efficiencies for kinds of coagulants follows the order: $Al_2(SO_4)_3$ < PSO-M < $Fe_2(SO_4)_3$. We shows that the flotation thickening system(1.6 $m^3$/d) could be continuously operated during two hours on operation conditions in the lab-scale experiments. Sludge thickening efficiency in the A/S ratio of 0.029 - 0.019 mL/mg was found to be very efficient, reaching to 300.0~335.7%.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.13 no.4
• /
• pp.107-117
• /
• 2005

The objective of this study was to investigate the proper operation conditions of fenton oxidation such as initial pH, $H_2O_2/Fe^{2+}$ ratio, $H_2O_2/Fe^{2+}$ dosage amount, and neutralizing agent for pretreatment of the livestock wastewater. Fenton oxidation reagents were reacted with the livestock wastewater for 2 hours at 120 rpm and the settling was performed for 2 hours using jar-tester apparatus under the different experimental conditions. And then the supernatant was sampled and measured for the residual $H_2O_2$, $COD_{Cr}$, and SS. The results are as follows; optimum initial pH=4, optimum $H_2O_2/Fe^{2+}$ ratio=10:1, optimum $H_2O_2/Fe^{2+}$ dosage amount=5,000/500 mg/L and $Ca(OH)_2$ as proper neutralizing agent. The removal efficiency of $COD_{Cr}$ and SS were 43% and 84% under those optimal fenton oxidation conditions.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.14 no.1
• /
• pp.151-159
• /
• 2006

In these days, the importance of sludge treatment is emerging due to the London Convention, so this study was conducted to propose the alternatives for the improved sludge treatment on the organic wastewater and sewage sludge with JAR test and settling column equipped with stirrer. The minimum coagulant dosage to earn the optimum sludge settling efficiency resulted from 200mg/l and each critical sludge settling interface showed no distinct difference when PAC was dosed over 200mg/l. Accordingly, Clarification Rate(CR) with 200mg/l dosage was calculated to CR=(Ho-Ht) / Ho=1-0.4=0.6 because the critical sludge settling height stopped at 0.4. The settling velocity of sludge interface was decreased with the increase of MLSS concentration but rather increased with MLSS concentration over 1,000mg/l. This resulted from positive effect of interacted coagulation for floc formation by transfer to the zone of compressed settling when MLSS concentration increased over 1,000mg/l. The settling velocity of sludge interface showed $28.66{\times}10^{-3}/min$ for average settling velocity of sewage sludge which is 6.7 times higher than $4.25{\times}10^{-3}/min$ for average settling velocity of organic wastewater sludge. The increasing rate of CR for organic wastewater activated sludge was higher than that of settling velocity under 200mg/l of PAC dosage but settling velocity was higher than CR over 200mg/l of PAC dosage. However, in case of sewage sludge, the differential rate of CR was low when PAC dosage was increased but the settling velocity was suddenly increased with over 200mg/l dosage. Therefore coagulation effect was more efficient to MLSS settling velocity rather than SS removal effect in the supernatant.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.33 no.5
• /
• pp.455-462
• /
• 2000

The objective of this study was to examine the physicochemical characteristics of coagulation reaction between loess and red tide organisms (RTO) and its feasibility, in developing a technology for the removal of RTO bloom in coastal sea. The physicochemical characteristics of loess were examined for a particle size distribution, surface characteristics by scanning electron microscope, zeta potential, and alkalinity and pH variations in sea water. Two kinds of RTO that were used in this study, Cylindrothen closterium and Skeietonema costatum, were sampled in Masan bay and were cultured in laboratory. Coagulation experiments were conducted using various concentrations of loess, RTO, and a jar tester. The supernatant and RTO culture solution were analyzed for pH, alkalinity, RTO cell number. A negative zeta potential of loess increased with increasing pH at $10^(-3)M$ NaCl solution and had -71.3 mV at pH 9.36. Loess had a positive zeta potential of +1,8 mV at pH 1.98, which resulted in a characteristic of material having an amphoteric surface charge. In NaCl and $CaCl_2$, solutions, loess had a decreasing negative zeta potential with increasing $Na^+\;and\;Ca^(+2)$ ion concentration and then didn't result in a charge reversal due to not occurring specific adsorption for $Na^+$ ion while resulted in a charge reversal due to occurring specific adsorption for $Ca^(+2)$ ion. In sea water, loess and RTO showed the similar zeta potential values of -112,1 and -9.2 mV, respectively and sea sand powder showed the highest zeta potential value of -25.7 mV in the clays. EDLs (electrical double-layers) of loess and RTO were extremely compressed due to high concentration of salts included in sea water, As a result, there didn't almost exist EDL repulsive force between loess and RTO approaching each other and then LVDW (London-yan der Waals) attractive force was always larger than EDL repulsive force to easily form a floe. Removal rates of RTO exponentially increased with increasing a loess concentration. The removal rates steeply increased until $800 mg/l$ of loess, and reached $100{\%}$ at 6,400 mg/l of loess. Removal rates of RTO exponentially increased with increasing a G-value. This indicated that mixing (i.e., collision among particles) was very important for a coagulation reaction. Loess showed the highest RTO removal rates in the clays.

• Applied Chemistry for Engineering
• /
• v.10 no.6
• /
• pp.889-894
• /
• 1999

Preparation of micron size polymer particles which have desired morphology, size, and structure by emulsion polymerization is very difficult due to coagulation of latex particles and formation of second generation particles. But there are attractive merits such as preparation of structural and functional polymer particles in seeded emulsion polymerization. Seeded emulsion polymerization of n-butyl acrylate(BA) was carried out to investigate the effects of stirring rate, reaction temperature, concentration of initiator, emulsifier, and cross-linking agent on the particle size and size distribution. By the combination of suitable reaction conditions, we succeeded in preparing $0.14{\sim}3.67{\mu}m$ diameter of poly(n-butyl acrylate)(PBA) particles using sequential seeded emulsion polymerization.