• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.12
• /
• pp.1027-1035
• /
• 2016

In this study, a strain-controlled fatigue test of widely-used 316L stainless steel with excellent corrosion resistance and mechanical properties was conducted, in order to assess its fatigue life. Low cycle fatigue behaviors were analyzed at room temperature, as a function of the strain amplitude and strain ratio. The material was hardened during the initial few cycles, and then was softened during the long post period, until failure occurred. The fatigue life decreased with increasing strain amplitude. Masing behavior in the hysteresis loop was shown under the low strain amplitude, whereas the high strain amplitude caused non-Masing behavior and reduced the mean stress. Low cycle fatigue life prediction based on the cyclic plastic energy dissipation theory, considering Masing and non-Masing effects, showed a good correlation with the experimental results.

• Geotechnical Engineering
• /
• v.10 no.4
• /
• pp.103-118
• /
• 1994

The rapid motion of granular material is microscopically observed, and investigated by continuum theory. From the binary collision phenomenon two different times are introduced : flying time and contact time. The former says the non -stationary motion and at a same time the variation of bulk volume. The latter is operative by a delayed time during the contact and describes the elastic properties of granular material. With both times a dynamic constitutive equation is postulated for four state variables : dispersive pressure, viscosity, thermal diffusivity and energy annihilation rate. The balance laws of mass, momentum and energy which are represented through above four variabls, are applied to the model, in which due to the elastic property the relaxation and energy absorption are explained.

• Journal of the Korean Geosynthetics Society
• /
• v.21 no.4
• /
• pp.69-78
• /
• 2022

Geotextile tubes are widely used to prevent erosion in coastal areas and to replace the backfill for shore slopes in the reclamation of land using dredged soil. In this study, The triaxial confining pressures were chosen as 10kPa, 50kPa, or 100kPa for the specimens reinforced with geotextile considering the condition in the site. The strain behavior under various compressive stresses was then identified. At strains 0% to 7%, the stress-strain behavior was the same due to the effect of initial strain hardening, in which the force was exerted according to the relaxation of the geotextile regardless of the confining pressure (≤100kPa). At strains of 7% or more, the specimen with the small confining pressure had smaller deformation under load, which increases the tensile resistance provided by the reinforcing geotextile. Brittle fracture was then observed due to strain softening and the deviator stress abruptly decreased. This is different from the phenomenon in which the shear strength increases as the confining pressure increases in general triaxial compression tests. In the geoxtile-confined tests, geotextiles are primarily subjected to tensile displacement. Thereafter, the modulus of elasticity increases rapidly, which exhibits the elastic behavior of the geotextile.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.2A
• /
• pp.261-271
• /
• 2006

Many uncertainties affecting to the structural behavior of prestressed concrete (PSC) bridges reinforced with the un bonded external tendons are analyzed on the basis of the analytical method introduced in the companion paper. Many design parameters, which must be considered in design procedure, such as friction slip at the deviators, number of deviators, time-dependent deformations of concrete, relaxation of tendon and influence of loading history in PSC bridges are reviewed, and a lot of valuable results are obtained through this parametric study. In advance, the structural responses according to the external tendon profiles are analyzed to grasp if an optimum tendon profile depends on the applied loading type, and the obtained results show that the most stable structural response is revealed when the locations of deviators are coincident with the loading points.

• Polymer(Korea)
• /
• v.36 no.5
• /
• pp.555-563
• /
• 2012

Warpage of injection molded product is caused by non-uniform shrinkage during shaping operation and relaxation of residual stress. Robust part design and glass fiber reinforced reins have been adopted to prevent warpage of part. Warpages for part designs have been investigated in this study according to the injection molding conditions. Part design contains flat specimen and two different rib designs in the flat part. Resins used in this study were glass fiber reinforced amorphous plastics, PC and ABS. Different rib designs showed significant differences of warpages in the parts. Various warpages have been observed in the three regions of the part, near gate region, opposite region to the gate, and flow direction region. Results of computer simulation revealed that the warpages were strongly related to glass fiber orientation. Flat specimen showed the smallest warpage and the specimen with ribs to the flow direction showed a high resistance to warpage. Warpage highly depended upon part design rather than molding condition. It was concluded that the rib design and selection of gate location in injection molding would be the most important factors for the control of warpage since those are directly related to the fiber orientation during molding.

• Proceedings of the Korea Inteligent Information System Society Conference
• /
• 2000.11a
• /
• pp.257-266
• /
• 2000

산업 및 가정용 기기들이 점차 복잡해짐에 따라 다양한 공학 분야의 해석 기술을 동시에 고려하면서 이들 원리를 적용한 최적의 설계를 결정하는 방법론의 필요성이 대두되고 있다. 다분야통합최적설계 또는 MDO(Multidisciplinary Design Optimization)라 일컫는 새로운 기술은 이러한 필요에 대응하는 기술로서 국내외적으로 활발한 연구가 진행되고 있다. 이러한 MDO 기술을 구현하는 소프트웨어와 하드웨어 복합 체계를 MDO 프레임웍(framework)이라 한다. 일반적으로 프레임웍이란 실제 응용프로그램의 용도에 맞는 주문제작(customization)이 가능한 일종의 전단계 프로그램이라 할 수 있다 MDO 프레임웍은 설계 및 해석 도구들간의 인터페이스를 제공하고, 이들 도구들이 사용하는 설계 데이터를 효율적으로 공유할 수 있도록 지원하여, 설계 작업을 정의, 실행, 관리하는 역할을 한다. 이러한 MDO 프레임웍은 설계 작업을 통합적으로 관리하고 자동화하여 설계 도구간의 데이터 전달과 변환에 소묘되는 설계자의 부담을 경감시키며 다분야 전문가가 참여하는 공통 작업 환경을 제공함으로써 설계 효율성을 증진시킨다. 본 논문에서는 이러한 효용을 달성하기 위한 MDO 프레임웍(framework)을 제시하고 프레임웍 설계의 논리적 근저와 타당성을 밝힌다. 본 논문에서 제안하는 다분야 통합 최적화를 위한 분산형 지능 시스템인 DisMDO는 사용자가 GUI를 동해서 편리하게 다분야통합최적화 문제를 해결할 수 있도록 지원하며, 제공되는 스크립트 언어를 동해서도 이를 정의할 수 있도록 지원하여 일괄처리도 가능하도록 한다. 또한, 집중화된 데이터베이스를 관리하여 다분야 전문가들이 공통의 데이터를 안전하게 공유할 수 있도록 지원하며, 외부에서 제공되는 해석 도구나 최적화 모듈을 손쉽게 프레임웍에 통합시킬 수 있도록 하는 인터페이스 제작기(factory) 기능을 제공한다.ackscattering spectroscopy, X-ray diffraction, secondary electron microscopy, atomic force microscoy, $\alpha$-step, Raman scattering spectroscopu, Fourier transform infrared spectroscopy 및 micro hardness tester를 이용하여 기판 bias 전압이 DLC 박막의 특성에 미치는 영향을 조사하였다. 분석결과 본 연구에서 제작된 DLC 박막은 탄소와 수소만으로 구성되어 있으며, 비정질 상태임을 알 수 있었다. 기판 bias 전압의 증가에 따라 박막의 두께가 감소됨을 알 수 있었고, -150V에서는 박막이 거의 만들어지지 않았으며, -200V에서는 기판 표면이 식각되었다. 이것은 기판 bias 전압과 ECR 플라즈마에 의한 이온충돌 효과 때문으로 판단되며, 150V 이하에서는 증착되는 양보다 re-sputtering 되는 양이 더 많을 것으로 생각된다. 기판 bias 전압을 증가시킬수록 플라즈마에 의한 이온충돌 현상이 두드러져 탄소와 결합하고 있던 수소원자들이 떨어져 나가는 탈수소화 (dehydrogenation) 현상을 확인할 수 있었으며, 이것은 C-H 결합에너지가 C-C 결합이나 C=C 결합보다 약하여 수소 원자가 비교적 해리가 잘되므로 이러한 현상이 일어난다고 판단된다. 결합이 끊어진 탄소 원자들은 다른 탄소원자들과 결합하여 3차원적 cross-link를 형성시켜 나가면서 내부 압축응력을 증가시키는 것으로 알려져 있으며, hardness 시험 결과로 이것을 확인할 수 있었다. 그리고 표면거칠기는 기판 bias 전압을 증가시킬수록 더 smooth 해짐을 확인하였다.인하였다.을 알 수 있었다. 즉 계면에서의 반응에 의해 편석되는 Ga에 의해 박막의 strain이 이완되면, pinhole 등의 박막결함

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.16 no.1
• /
• pp.123-136
• /
• 2018

The objective of this study is to propose a new methodology to fabricate a reliable engineering-scale buffer block, which shows homogeneous and uniform distribution in buffer block density, for in-situ experiments. In this study, for the first time in Korea, floating die press and CIP (Cold Isostatic Press) are applied for the manufacture of an engineering-scale bentonite buffer. The optimized condition and field applicability are also evaluated with respect to the method of manufacturing the buffer blocks. It is found that the standard deviation of the densities obtained decreases noticeably and that the average dry density increases slightly. In addition, buffer size is reduced by about 5% at the same time. Through the test production, it is indicated that the stress release phenomenon decreases after the application of the CIP method, which leads to a reduction in crack generation on the surface of the buffer blocks over time. Therefore, it is confirmed that the production of homogeneous buffer blocks on industrial scale is possible using the method suggested in this study, and that the produced blocks also meet the design conditions for dry density of buffer blocks in the AKRS (Advanced Korea Reference Disposal System of HLW).