• Journal of the Korean Society of Hazard Mitigation
• /
• v.1 no.2 s.2
• /
• pp.103-114
• /
• 2001

As the results of comparison with several anchorage design methods of PSC box girder, stress superposition effect by the order of prestressing force can't be considered in the case of multi-anchorage design with existing design methods. In anchorage design by 3-D finite element analysis, estimation of stress concentration region and stress flow are correctly defined, but the estimation of sectional forces in anchorage is very complicated. In the case of anchorage design by strut-tie model method, the stress superposition effect can be considered and sectional forces in anchorage are easily calculated. Therefore, strut-tie model method is remarkably suitable to anchorage design if geometrical conditions of the truss members are carefully considered.

• Magazine of the Korea Concrete Institute
• /
• v.11 no.1
• /
• pp.279-288
• /
• 1999

The creep of concrete structures caused by variable stresses is generally calculated by step-by-step method based on the superposition of creep function. Although most practical application is carried out by this linear assumption. significant deviations between predictions and experiments have been observed when unloading takes place, that is. stress is reduced. This shows that the superposition of creep function does not describe accurately the effect of sustained compressive preload. The main purpose of this study is to propose a creep analysis model which is expressed with both creep function and creep recovery function where increase or decrease of stress is repeated. In these two function method, the creep behavior is modelled by using linear creep law for loading and creep recovery law for unloading. To apply two function method to time analysis of concrete structures, the calculation method of creep strain increment under varying stress is proposed. The calculation results based on the present method correlates very well with test data, but the conventional superposition method exhibits large deviation from test results. This paper provides a more accurate method for the time dependent analysis of concrete structures subjected to varying stress, i.e. increasing or decreasing stress. The present method may be efficiently employed in the revision of future concrete codes.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.93-93
• /
• 2009

본 연구에서는 EGW, FCAW 공정 적용에 따른 고강도 극후판 EH36-TMCP강 용접부의 역학적 거동 및 파괴인성 $K_{IC}$ 을 규명하기 위해, 먼저 열분포, 열탄소성 수치해석을 통하여 용접부의 역학적 거동(용접잔류응력, 소성변형율 등의 크기, 분포, 발생기구)을 고찰하였다. 그리고 이때 얻어진 잔류응력을 초기응력으로 하여, 잔류응력과 외력의 복합하중에 대한 파괴인성 $K_{Ic}$ 특성을 해석하였다. 용접공정별 균열이 존재하는 용접부의 파괴기준을 살펴보면, EGW용접부의 경우가 FCAW용접부의 경우에 비해 균열의 성장이 다소 용이하여 $K_{IC}$ 값이 다소 낮게 나타났다. EGW용접부의 파괴인성 $K_{IC}$ 경우 중첩된 경우(복합하중)가 순수 외력만 작용하는 경우보다 파괴 인성치가 다소 감소하는 경향을 보이고, a/W가 작을 경우 중첩의 경우가 순수 외력만의 경우보다 파괴인성치 차이가 크나, a/W가 증가함에 따라 그 차이가 점차 없어지는 것으로 나타났다. 반면, FCAW용접부의 경우 균열길이가 작은 범위에서는 중첩된 경우가 순수 외력만 작용 할 경우보다 파괴 인성치가 다소 증가함을 보이지만, a/W가 증가함에 따라 순수 외력만의 작용의 경우와 중첩의 경우의 파괴인성 차이가 없는 것으로 나타났다.

• Korean Journal of Food Science and Technology
• /
• v.27 no.2
• /
• pp.193-198
• /
• 1995

The changes in the rheological properties of soybean curd upon the various storage temperatures ($5{\sim}25^{\circ}C$) were measured by the stress-relaxation test and analysed by time-temperature superposition theory. As the storage temperature was lower, higher initial and equilibrium stress of soybean curd were observed. When the stress-relaxation curves were moved horizontally by using the shift-factor on the basis of reference temperature, the master curve was obtained. By applying master curve and shift-factor to the WLF (Williams-Landel-Ferry) equation, activation energy (30kcal/mol) was calculated and storage time at the specific temperature could be predicted, suggesting the equivalent shelf-life of soybean curd texture.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.10
• /
• pp.1339-1344
• /
• 2010

MSM (Modal Superposition Method) is a technique for analyzing structural durability by taking the vibration characteristics into consideration. In this paper, MSR (Modal Stress Recovery) method, which is similar to MSM, was reviewed to check its validity as a durability analysis method. The MSR method directly calculates the modal displacement time history in multibody dynamics analysis; as a result, the total analysis time is shorter than that of MSM method. We conduct durability analysis using the MSR method and a durability test of a torsion beam axle that is affected by various road loads within the natural frequency of the beam axle. The analysis results for critical location and durability were in good agreement with the respective test results. Therefore, durability analysis using the MSR method is effective in predicting the durability of the structures of various dynamic systems.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.5
• /
• pp.428-431
• /
• 2005

In this paper, the displacement and stress of pile foundation constructed in the soft cohesive soils were measured and investigated at each construction phase. The piles belongs to compressive stress then extension due to lateral flow of soft soils. Battered piles showed different stress state according to construction direction. The lateral displacements of piles radically occurred at the embankment phase.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.172-181
• /
• 2003

In this study, the stress intensity factor of center crack tip is calculated by the superposition method when it is surrounded by symmetrically distributed small cracks. The values of stress intensity factors of center crack tips are compared with those of the center crack tips calculated by the superposition method. These compared errors are influenced by the locations of distributed small cracks. These errors are inspected. When small cracks overlap and approach near the center crack tip, the effect of interaction caused by these cracks becomes noticeable and these errors become larger. In case of multiple distributed small cracks except this case, the stress intensity factor of the center crack tip is easily calculated by the superposition method.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.11
• /
• pp.244-250
• /
• 1998

In this study, the stress intensity factors of center crack are analyzed when it is surrounded by symmetrically distributed small cracks. The values of stress intensity factors of the center crack are greatly influenced by the locations of distributed small cracks. When small cracks overlap or approach near the tip of a center crack, the effect of interaction arisen by these cracks becomes noticeable. In case of multiple distributed small cracks, the stress intensity factor of a center crack is found to be efficiently determined by the superposition method.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.22 no.6
• /
• pp.565-572
• /
• 2009

This work intends to establish the reliability and fracture toughness $K_{IC}$ criterion of welded joints by EGW for high strength EH36-TMCP ultra thick plate. For this, firstly thermo elasto-plastic analysis has been carried out on two pass X-groove butt joint model to clarify the thermal and mechanical behaviour(residual stress, plastic strain, magnitude of stress and their distribution and production mechanism). Moreover, to establish fracture criterion, analysis of fracture toughness $K_{IC}$ has been performed under the notch machined and residual stress with the load condition on EGW welded joints. A quantitative fracture criterion for EGW welded joints is suggested by using $K_{IC}$.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.3
• /
• pp.83-94
• /
• 2001

본 연구에서는 상.하단으로 구분된 2개의 동일한 보강토옹벽에 대해서 상호 이격거리에 따른 수치해석을 수행하여 전면벽체의 수평변위, 전면벽체 배면의 수평토압, 보강토체 배면의 수평토압 그리고 보강재의 최대인장력 분포 및 크기변화 양상 등 다단식 보강토옹벽의 거동을 살펴보았다. 또한, 하단 옹벽에 증가되는 응력을 산정하고자 중첩의 원리를 적용한 2:1 응력분포법을 제시하였다. 수치해석 결과 이격거리가 증가함에 따라 상단옹벽이 하단옹벽에 미치는 영향이 감소하였으며 하단 옹벽 높이의 두배 이상 이격시, 상호 거동은 독립옹벽으로 거동하였다. 하단 옹벽내 응력 산정방법에 있어서 NCMA의 방법이 가장 보수적인 결과를 보였으며 본 연구에서 제시한 2:1 응력분포법중 주동파괴면을 고려하지 않은 방법이 수치해석 결과와 가장 유사하게 나타났다.