• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.5B
• /
• pp.529-537
• /
• 2006

This paper investigates the impacts of the drag-related weighting coefficients on mean velocity and turbulence structures. The transport equations for the Reynolds stress of vegetated open-channel flows are derived by using the temporal- and horizontal-averaging scheme. It is found that the total Reynolds stress of vegetated open channel flows consists of the Reynolds stress due to temporally fluctuating velocities and the Reynolds stress due to spatially fluctuating velocities. The drag-related weighting coefficient $C_{fk}$ for the total Reynolds stress component is found to be unit, while the coefficient for the Reynolds stress due to temporally fluctuating velocities can be negligible. This is the reason why very small weighting coefficients in previous studies yield very good agreements with measured data. In other words, the Reynolds stress due to spatially fluctuating velocities remains still unknown, especially due to the large number of measuring locations. Through a developed Reynolds stress model, vegetated open-channel flows are simulated and compared with measured data from the literature. Comparisons reveal that the computed mean flow and Reynolds stress structures are hardly affected by the drag-related weighting coefficients. However, the computed turbulence intensity profiles are significant different with the drag-related weighting coefficients. A budget analysis of the transport equations for the Reynolds stress component is carried to investigate why turbulence intensity is affected by the drag-related weighting coefficients.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.4
• /
• pp.57-63
• /
• 2004

The range of stresses experienced in subgrade soils and subbase materials in pavement under working stress conditions is below about 150㎪. Therefore, the deformational characteristics of soils at low confining pressures are important properties in the analysis and design of pavement system. Subgrade soils and subbase materials were collected from the actual pavement projects for testing. To evaluate the effect of confining pressure on modulus of those materials at low confining pressures, RC and FFRC tests were performed. Interestingly, the relationship between modulus of soils and confining pressure is more appropriate in linear space than in logarithm space at low confining pressure. Based on those results, new model fur evaluating the effects of confining pressure on modulus at low confining pressures was proposed.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.14 no.4
• /
• pp.286-294
• /
• 2002

This study investigated the effects of stress and time history of overconsolidated clayey soils on pore pressure parameter, A. Laboratory tests were carried out under the conditions of both varying stress and time history. The stress history is classified into (i) rotation angle of stress path, (ii) overconsolidation ratio, and (iii) magnitude of length of recent stress path. The time history is divided into (i) loading rate of recent stress path and (ii) rest time. Pore pressure parameters are different both in the magnitude and trend with the rotation angle, depending on the magnitude of overconsolidation ratio but not in a trend. In addition, the pore pressure parameters have no effects on the magnitude of length of recent stress path except the level of initially small strain, while loading rates of recent stress path have effects on it. Finally, the pore pressure parameters of overconsolidated clays increase with the existence of the rest time, until either the deviator stress exceeds 70 kPa or the strain up to 0.1%.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.52-55
• /
• 2010

본 논문에서는 일반유한요소법(Generalized Finite Element Method)를 이용하여 응력확대계수를 계산하는 방법을 소개한다. 기존의 유한요소법을 사용하여 응력확대계수를 계산하기위해서는 J-integral 방법 등을 이용한 후처리 과정이 필수적으로 요구된다. 뿐만 아니라 균열선단 근방에서의 응력을 기술하기 위해서는 세밀한 요소망(mesh)이 요구된다. 후처리 과정과 균열선단 근방에서의 요소망은 수치적 오류를 발생시키고 이는 정확한 응력확대계수를 얻는데 어려움을 준다. 일반유한요소법은 근사함수를 요소망의 영향 없이 추가해서 사용할 수 있는 장점을 가지고 있지만, 활용성 측면에서 기존의 유한요소법보다 복잡하여 실용성이 떨어진다. 본 논문에서는 일반유한요소법의 장점을 충분히 살려 균열선단근방에서는 응력을 모델링하여 근사함수로 사용하고 균열선단에서 거리가 먼 곳은 기존의 유한요소를 써서 계산을 하였다. 특별한 후처리 과정(Post processing) 없이 비교적 정확한 응력확대계수를 손쉽게 얻을 수 있다. 일반유한요소법을 이용한 제시된 방법론이 타당함을 수치 예제를 통하여 확인하였다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.5
• /
• pp.1462-1471
• /
• 1991

본 연구에서는 미소 결함주위에서 발생, 전파하는 균열들에 미치는 초기 결함 깊이와 상호 간섭 영향을 검토하기 위하여 기존 재료가 갖고 있는 결함이나 비금속 개 재물로 대신할 수 있다고 생각되는 미소 원공의 크기를 변화시킨 모델에 대해 유한 요 소법을 이용하여 3차원적으로 응력을 해석하였다. 실제 사용하고 있는 부재에 결함 들이 존재할 경우 응력장의 간섭으로 피로 균열 진전이 가속화됨으로 미소 원공 주위 의 응력 분포 및 미소 원공사이의 응력장의 간섭과 미소 원공에서 발생, 전파하는 표 면 균열의 응력 확대 계수에 미치는 영향에 대하여 비교검토 하였다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.5
• /
• pp.1538-1550
• /
• 1991

본 연구에서는 접합된 두 층이 유한한 두께를 가지고, 또한 균열은 임의의 각 도로 기울어져 있는 경우의 문제를 해석하여 층의 두께 등이 응력강도계수에 미치는 영향을 살펴보았다.

• Geotechnical Engineering
• /
• v.14 no.5
• /
• pp.219-234
• /
• 1998

Modulus measurements in vertical boreholes under simulated horizontal in-situ stress conditions were performed on laboratory rock specimens. The experimental program was focused on the examination of modulus change with the variation of the orientation, magnitude and ratios of horizontal biaxial stresses. The experiment results show that the modulus increases when the magnitude of the horizontal stresses increases. The modulus measured in the minimum principal direction increased when the ratio between the horizontal principal stresses increased, while the modulus measured in the maximum principal direction decreased when the ratio of the horizontal principal stresses increased. These were caused by the tangential stresses that vary depending upon the magnitude of horizontal stresses, the applied pressure and the orientation of measurement. Also, the measured moduli were determined under tensile stress, compressive stress, or both stresses. Thus, the stress effect on deformation modulus should be considered, not only for the interpretation of the results of borehole deformability measurement, but also for the design of underground gas storage and pressure tunnel, and for the interpretation of tunnel monitoring.

• International Journal of Highway Engineering
• /
• v.8 no.4 s.30
• /
• pp.13-24
• /
• 2006

The stresses in concrete pavement systems are larger when vehicle loads are applied at pavement edges, and these large stresses significantly affect the behavior and performance of pavements. Therefore, in this study, the stress distribution and the critical stresses in concrete pavements were investigated using a finite element model when dual-wheel single-, tandem-, and tridem-axle loads were applied at pavement edges. First, the stress distribution along the longitudinal and transverse directions was analyzed, and then the effects of slab thickness, concrete elastic modulus, and foundation stiffness on the stress distribution were investigated. The effect of the tire contact pressure related to the tire print area was also studied. The location of the critical stress occurrence in concrete pavements was finally investigated. From this study, it was found that the critical concrete stress due to edge loads became larger as the concrete elastic modulus increased, the slab thickness increased, and the foundation stiffness decreased. The effect of the tire contact pressure on the critical stress was clear as the slab thickness became smaller. The critical stress location in the transverse direction was independent of the concrete elastic modulus and the foundation stiffness; however, it moved into the interior as the slab thickness increased. The critical stress location in the longitudinal direction was under the axle for single- and tandem-axle loads, but for tridem-axle loads, it tended to move under the middle axle from the outer axles as the concrete elastic modulus and/or slab thickness increased and the foundation stiffness decreased.

• Journal of the Society of Naval Architects of Korea
• /
• v.33 no.3
• /
• pp.1-7
• /
• 1996

The stress concentration factor gives the significant effect the fatigue strength of welded joints. The model used herein is the type of the load carrying fillet welded cruciform joint with full or partial penetration. In order to obtain the stress concentration factor at the weld toe of fillet joint, the reasonable element size of the toe part is investigated and the stress analysis for the series models by FEM under tensile load is performed. On the basis of the calculation results, the estimated formulae for the stress concentration factor(Kt) at weld toe part of the fillet welded joint, which the effect of toe radius, flank angle and other parameters are taken into account, is derived.

• Journal of the KSME
• /
• v.31 no.4
• /
• pp.356-363
• /
• 1991

선형 탄성 유한요소 응력해석과 평균응력 효과를 고려한 저주기 피로실험으로부터 결정된 피로 특성, 그리고 국부변형률 방법을 종합하여 외경에 흠이 존재하는 자긴가공된 두꺼운 압력 용기의 피로수명이 평가되었다. 직사각형의 매우 날카로운 흠에서의 응력집중계수는 타원형 홈에서의 응력집중계수의 약 두배의 값이 얻어졌으며, 고강도 압력용기강인 ASTM A723의 저주기 피 로거동에 대한 평균응력 영향은 Morrow 및 SWT 파라메타를 이용하여 충분히 고려되었다. 균열발생이 예상되는 위험한 부분인 홈의 뿌리부분에서의 국부적인 응력, 변형률이 계산되었으며 예측된 피로수명은 실험적으로 얻어진 수명과 비교했을 때 2에서 4배의 오차를 보이면서 일치 하는 결과를 얻었다.