• Journal of the Korea Concrete Institute
• /
• v.14 no.6
• /
• pp.942-948
• /
• 2002

When fresh concrete is exposed to low temperature, the concrete may suffer frost damage due to freezing at early ages and the strength development may be delayed. One of the solution methods to resolve these problems is to reduce freezing temperature of concrete by the use of chemical admixture called Accelerator for freeze protection. In this study we Investigate the effect on the strength development of cement mortar using accelerator for freeze protection with the variable curing condition. As the result of this study, the mortar using accelerator for freeze protection show continuously the strength development in curing condition of -5$^{\circ}C$. And the compressive strength under variable temperature condition was higher than constant temperature condition in same maturity.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2015.11a
• /
• pp.143-144
• /
• 2015

In this research it was attempted to analyze the general engineering properties of low cement mortar according to the type of setting accelerator and substitution rate, when 1% substitution rate for setting accelerator was used a high rate of compressive strength manifestation was shown and that the WS-10 type setting accelerator was appropriate. For the rate of change of length, when 3% substitution rate for setting accelerator was used, it was shown that due to initial expansion the shrinkage compensation was not significant, and when taking into consideration strength and shrinkage, 1% of WS-10 was shown to be appropriate.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.14 no.3
• /
• pp.192-200
• /
• 2002

There is a volume change between the sediments and the dredged materials because the dredged materials is fully disturbed by the dredger and settled in the basin from the stabilized condition. The volume of the dredged materials is also affected by the coagulants and flocculants (hereafter C & F) which was used to speed up the settling of the suspended solids. In this study, the volume change of the dredged materials is analysed in detail due to the injection amount of the C & F. The dredged materials were sampled in the lagoon located in the East coastal zone, and the volume change of the samples is quantitatively analysed by the laboratory test due to the change of the clay content and the amount of the C & F. The optimal amounts of the C & F is determined by showing the minimal volume change due to C & F injection. From the experimental results, the volume of the dredged materials is increased 1.68 times on an average and the volume change rate is slightly increased, i.e., negligible, as the clay content increase in the case of the C & F injection.

• Journal of the Korean GEO-environmental Society
• /
• v.5 no.4
• /
• pp.5-11
• /
• 2004

When settled sediments in natural condition for long time were dredged by dredging process, it is natural that bulking change between sediments and dredged soils is affected by chemical injection; coagulant. Dredged sediments used in this study were sampled in the lagoon "Young rang lake" located at the east coast Sokcho city and the bulking change of dredged soils is quantitatively analysed by changing of the clay content and the amount of the flocculant and coagulant. From the experimental results, the bulking of dredged soils increased 1.69 times on the average bulking of settled sediments in natural condition in the case of the optimum chemicals addition.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.4
• /
• pp.257-264
• /
• 2003

Bulking change between sediments and dredged soils occurs when dredged soils are fully disturbed by dredging process and settled down to stabilized conditions in the basin. Bulking of dredged soils are affected by chemical injection, coagulant and flocculant, to speed up settling process of the suspended solids. In this paper, bulking changes of dredged soils are investigated by experimental works regarding injection effects of the coagulant and flocculant. Dredged sediments were sampled in the lagoon located at the East Coast, and the bulking change of dredged soils is quantitatively analysed by changing the clay content and the amount of the coagulant and flocculant. The optimal amounts of the coagulant and flocculant are determined based on minimal bulking change due to coagulant and flocculant injection. From the experimental results, the bulking of dredged soils increased 1.69 times on the average and the bulking change rate slightly increased as clay content increasea due to injection of the coagulant and flocculant.

• Journal of the Korea Institute of Building Construction
• /
• v.15 no.1
• /
• pp.25-33
• /
• 2015

In this study, initial crack index was evaluated by FEM analysis to find the crack propagation from hydration heat in precast concrete. As results, as the usage of hardening accelerator increased, initial compressive strength increased and setting time was shortened. Additionally, as amounts of hardening accelerators increased, the central temperature of concrete increased and the time to reach the highest temperature was shortened. It was demonstrated that the hardening accelerators accelerated the hydration reaction of cement, and caused the increase of hydration heat within the short period of time. Furthermore, the crack index for evaluating the heat level was performed by FEM. As results, there was no problem about the cracks, despite of the growth of initial high hydration heat. This is because of the increased tensile strength that is large enough to sustain the thermally induced-stress.

• Applied Chemistry for Engineering
• /
• v.8 no.5
• /
• pp.822-829
• /
• 1997

When $Al_2(SO_4)_3$ as an accelerator was added to $\beta$-hemihydrate gypsum, the setting time, mobility and compressive strength properties of $\beta$-hemihydrate gypsum were examined with the adding of two types grounded gypsum crushed by ball mill. By 15wt% adding of 7% $Al_2(SO_4)_3$ dilute solution, the setting time of $\beta$-hemihydrate gypsum was sharply accelerated than that of non-added $\beta$-hemihydrate gypsum. When ground phospho gypsum(PG) and chemical gypsum(CG) were added to $\beta$-hemihydrate gypsum, the initial and final setting time of $\beta$-hemihydrate gypsum were accelerated markedly with the increasing of grinding time and added amount of ground phospho gypsum. Especially, this trend largely presented when ground phospho gypsum was added to $\beta$-hemihydrate gypsum. The compressive strength of $\beta$-hemihydrate gypsum added by ground phospho and chemical gypsum was largely increased at initial curing time such as 1, 3 days. Particularly, the compressive strength of $\beta$-hemihydrate gypsum added by ground phospho gypsum was increased by 15~20% than that of ground chemical gypsum.

• Journal of the Korea Concrete Institute
• /
• v.29 no.4
• /
• pp.407-413
• /
• 2017

The fundamental property of magnesia phosphate cement (MPC) for concrete repair material was investigated in this research. For mechanical properties, setting time, compressive strength and tensile/flexural bond strength were measured, and hydration products were detected by X-ray diffraction. The specimens were manufactured with dead burnt magnesia and potassium dihydrogen phosphate was admixed to activate the hydration of magnesia and a borax was used as a retarder. To observe the pore structure and ionic permeability of MPC mortar, mercury intrusion porosimetry was performed together with rapid chloride penetration test (RCPT). As a result, time to set of Fresh MPC mortar was in range of 16 to 21 min depend on the M/P ratio. Borax helped delaying setting time of MPC to 68 min. The compressive strength of MPC with M/P of 4 was sharply developed to 30 MPa within 12 hours. The compressive strength of MPC mortar was in range of 11.0 to 30.0 MPa depend on the M/P ratio at 12 hours of curing. Both tensile and flexural bond strength of MPC to old substrate (i.e. MPC; New substrate to OPC; Old substrate) were even higher than ordinary Portland cement mortar (i.e. [OPC; New substrate] to [OPC; Old substrate]) does, accounting 19 and 17 MPa, respectively. The total pore volume of MPC mortar was lower than that of OPC mortar. MPC mortar had the entrained air void rather than capillary pore. The RCPT showed that total charge passed of OPC mortar had more than that of MPC mortar, which can be explained by the pore volume and pore distribution.

• Journal of the Korea Concrete Institute
• /
• v.25 no.2
• /
• pp.201-207
• /
• 2013

When hot weather concrete is utilized, the cooling methods of cooling pipe, liquid nitrogen, ice, etc., are used to prevent the poor consistency and cold joint due to high temperature. These methods, however, spike the production cost and energy consumption, and make quality control difficult. Among these methods is one that involves the use of a retarder. Although economical, retarder is caused difficulty of retarded hardening and setting time control due to inaccurate weighing and poor working condition. Therefore, how to make a tablet for hot weather concrete, as with the existing pharmacy and foods, is discussed in this study, including the following items: mortar setting time, flow test by elapsed time, physical and mechanical properties of concrete. As a result, gluconic acid is superior to lignosulfonic acid and the possibility of using them for such purpose without quality degradation was confirmed in this study, when retarder is tabletting.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.387-388
• /
• 2010

In this study, early-age properties of mortar containing calcium chloride as an accelerator was investigated. The time of setting of the mortar by ultrasonic tester and penetrometer was assessed to prove its acceleration effect on hydration and the compressive strength was also measured to examine the effect of calcium chloride on the early-age strength.