• Journal of the Korean Geosynthetics Society
• /
• v.4 no.4
• /
• pp.39-46
• /
• 2005

A series of numerical analyses on soft clay ground improved by plastic board drain(PBD) were carried out, in order to investigate the consolidation behavior considering viscosity of the improved ground. The applicability of numerical analyses, in which an elasto-viscoplastic three-dimensional consolidation finite element method is applied in this study, was confirmed through comparison between experimental and analytical results. As the analytical results, consolidation behavior of both settlement and excess pore pressure and effective stress in clay were elucidated. Then secondary consolidation characteristics of improved ground were estimated through compare with results of typical one-dimensional consolidation analysis.

• Magazine of the Korea Concrete Institute
• /
• v.9 no.5
• /
• pp.157-164
• /
• 1997

일반적으로 콘크리트와 철근간의 경계면을 나타내는 유한요소법에는 균열의 부근에서 발생하는 부착열화 현상을 고려하지 않고 있다. 이것은 균열 부근에서 과도한 부착을 초래하고 , 국소 변형과 균열의 진전에도 영향을 준다. 본 연구에서는 철근콘크리트 구조물의 균열부근에서 일어나는 부착거동의 변화를 고려한 비선형 부착응력-미끄럼 모델을 제안하였다. 철근과 콘크리트간의 경계면에는 링크요소를 이용하였고, 링크의 특성은 철근을 가로지르는 균열의 상태에 따라 변하도록 조정하였다. 균열의 형성상태를 정량화하고, 부착거동을 두 포락선 1) 균열로부터 충분히 떨어진 위치에서의 부착상태를 모델링한 외연포락선, 2)횡균열면에 있어서의 부착상태를 모델링한 내연포락선의 사이에 변이시키기 위하여 비국소적 손상도 개념을 도입하였다. 이 방법의 유효성을 알아보기 위하여 편재하중을 받는 T형 교각의 실험 및 해석결과를 제시하였다. 제안된 모델의 결과를 실험결과와 비교하여 본 모델의 유용성을 검증하였다.

• Journal of the Korean Society of Industry Convergence
• /
• v.3 no.1
• /
• pp.53-59
• /
• 2000

단섬유 보강 복합재료의 종횡비(aspect ratio)를 변화시키며 기계적 특성(탄성계수, 인장강도)을 평가하였다. 2차원 다중 파이버(multi-fiber) 모델을 이용하여 엇갈린(staggered) 배열과 규칙적(aligned) 배열에 대해 유한요소 해석을 하였다. 단섬유 복합재료의 유효탄성계수 및 인장강도는 섬유와 기지의 탄성계수비, 섬유 배열상태, 그리고 단섬유 종횡비의 함수로 표현되었으며, 해석결과의 탄성계수와 인장강도는 이론 모델의 결과와 사출 성형된 PEEK 복합재료 시험편의 결과와 비교하였다. 시험결과는 낮은 종횡비에서 이론 모델 결과와 일치함을 보였다. 단섬유 보강 복합재료의 배열 및 종횡비 변화에 따른 섬유보강 효과에 따른 계면응력 상태는 기계적 특성 결정에 중요한 영향을 보였다.

• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.2
• /
• pp.73-78
• /
• 1992

Numerical method by Abdi et al. for obtaining a stress singularity near a crack perpendicular to the interface between two elastic materials is reviewed. More efficient and simple method to obtain crack singularity by shifting a mid-side node of 8-node isoparametric element is presented. It is observed that the present analysis provides increased accuracy for the expression of the opening displacement and the determination of the optimal position of the mid-side node for a wide range of material properties.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.6
• /
• pp.27-44
• /
• 2015

An analytical solution of dynamic responses for seabed in finite and infinite thicknesses including shallow has been developed under flow and partial standing wave with arbitrary reflection ration coexisting field at a constant water depth condition. In the analytical solution, a field was simply transited to a coexisting field of progressive wave and flow when reflection ratio was 0 and to a coexisting field of fully standing wave and flow when reflection ratio was 1. Based on the Biot's consolidation theory, the seabed was assumed as a porous elastic media with the assumptions that pore fluid is compressible and Darcy law governs the flow. The developed analytical solution was compared with the existing results and was verified. Using the analytical solution the deformation, pore pressure, effective and shear stresses were examined under various given values of reflection ratio, flow velocity, incident wave's period and seabed thickness. From this study, it was confirmed that the dynamic response of seabed was quite different depending on consideration of flow, which causes changing period and length of incident and reflection waves. It was also confirmed that dynamic response significantly depends on the magnitude of reflection ratio.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.12
• /
• pp.959-966
• /
• 2013

In this study, based on P-3CK project using aging aircraft without any design information, the structural assessments of fastener holes to repair the short edge distance defects are investigated. For this purpose, the nacelle longeron which has many defects is selected and then conservative stress is calculated by performing the static analysis of 1.5ED, 1.8ED, 2.0ED defects of longeron fastener holes. This result applies to TWIST standard load spectrum to generate flight load spectrum. Then the crack growth analysis is performed by using flight load spectrum. Through this, the validity of a repaired fastener hole is evaluated. Finally, the standard of repair and the period of maintenance for a defected fastener hole are established.

• Tunnel and Underground Space
• /
• v.24 no.2
• /
• pp.143-154
• /
• 2014

In this study, we simulated both dissociation of gas hydrate and mechanical deformation of hydrate-bearing sedimentary formation using geomechanical model. The geomechanical model analysis consists of two distinct codes of TOUGH+Hydrate and FLAC3D. The model is characterized by the fact that changes of temperature, pressure, saturation and their influence on the consequent evolution of effective stress, stiffness and strength of hydrate-bearing sediments during gas production could be well simulated. We compared the results of simulation for two different production methods, and showed that combination of depressurization and thermal stimulation results in the enhancement of production rate especially at early stage. We also presented that the hydrate dissociation-induced geomechanical deformation in unconsolidated clay is much larger than that in sandstone.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.11
• /
• pp.1079-1089
• /
• 2015

In this paper, we propose a method to evaluate the material properties of high-yield strength materials exceeding 10GPa from spherical indentation. Using a regression equation considering four indentation variables, we map the load displacement relation into a stress-strain relation. To calculate the properties of high-strength materials, we then write a program that produces material properties using the loading / unloading data from the indentation test. The errors in material properties computed by the program are within 0.3, 0.8, and 6.4 for the elastic modulus, yield strength, and hardening coefficient, respectively.

• Journal of the Korea Concrete Institute
• /
• v.14 no.1
• /
• pp.58-66
• /
• 2002

The objective of this study is to examine the fracture characteristics of concrete at early ages such as critical stress intensity factor, critical crack-tip opening displacement, fracture energy, and bilinear softening curve based on the concepts of the effective-elastic crack model and the cohesive crack model. A wedge splitting test for Mode I was performed on cubic wedge specimens with a notch at the edge. By taking various strengths and ages, load-crack mouth opening displacement curves were obtained, and the results were analyzed by linear elastic fracture mechanics and the finite element method. The results from the test and analysis showed that critical stress intensity factor and fracture energy increased, and critical crack-tip opening displacement decreased with concrete ages from 1 day to 28 days. By numerical analysis four parameters of bilinear softening curve from 1 day to 28 days were obtained. The obtained fracture parameters and bilinear softening curves at early ages may be used as a fracture criterion and an input data for finite element analysis of concrete at early ages.

• Composites Research
• /
• v.25 no.4
• /
• pp.98-104
• /
• 2012

In recent years, degenerative spinal instability has been effectively treated with a cage. However, little attention is focused on the stiffness of the cage. Recent advances in the medical implant industry have resulted in the use of medical carbon fiber reinforced polymer (CFRP) cages. The biomechanical advantages of using different cage material in terms of stability and stresses in bone graft are not fully understood. A previously validated three-dimensional, nonlinear finite element model of an intact L2-L5 segment was modified to simulate posterior interbody fusion cages made of CFRP and titanium at the L4-L5 disc with pedicle screw, to investigate the effect of cage stiffness on the biomechanics of the fused segment in the lumbar region. From the results, it could be found that the use of a CFRP cage would not only reduce stress shielding, but it might also have led to increased bony fusion.