• Journal of the Korean Institute of Telematics and Electronics
• /
• v.21 no.1
• /
• pp.62-70
• /
• 1984

N+NPP+ HLEBSF (high low emitter back surface field) solar cells which have N+N high low junction in the emitter as well as N+PP+ BSF cells were designed and fabricated by using <111> oriented P type Si wafers with the resistivity of 10$\Omega$/$\textrm{cm}^2$ and the thickness of 13-15 mil. Physical parameters (impurity concentration, thickness) at each region of N+PP+ and N+NPP+ cell were made equally through same masks and simultaneous process except N region of HLEBSF cell to investigate the high low emitter junction effect for efficiency improvement. Under the light intensity of 100 mW/$\textrm{cm}^2$, total area (active area) conversion efficiency were typically 10.94% (12.16%) for N+PP+ BSF cells and 12.07% (13.41%) for N+N PP+ cells. Efficiency improvement of N+NPP+ cell which has high low emitter Junction structure is resulted from the suppression of emitter recombination current and the increasement of open circuit voltage (Voc) and short circuit current (Ish) by removing heavy doping effects occurring in N+ emitter region.

• Journal of radiological science and technology
• /
• v.40 no.1
• /
• pp.49-55
• /
• 2017

In the case of nuclear medicine practitioners in medical institutions, a wide range of exposure dose to individual workers can be found, depending on the type of source, the amount of radioactivity, and the use of shielding devices in handling radioactive isotopes. In this regard, this study evaluated the organ dose on practitioners as well as the dose reduction effect of the L-block shielding device in handling the diagnostic radiation source through the simulation based on the Monte Carlo method. As a result, the distribution of organ dose was found to be higher as the position of the radiation source was closer to the handling position of a practitioner, and the effective dose distribution was different according to the ICRP tissue weight. Furthermore, the dose reduction effect according to the L-block thickness tended to decrease, which showed the exponential distribution, as the shielding thickness increased. The dose reduction effect according to each radiation source showed a low shielding effect in proportion to the emitted gamma ray energy level.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.170-170
• /
• 2012

최근 주목받고 있는 amorphous InGaZnO (a-IGZO) thin film transistors (TFTs)는 수소가 첨가된 비정질 실리콘 TFT (a-Si;H)에 비해 비정질 상태에서도 높은 이동도와 뛰어난 전기적, 광학적 특성에 의해 큰 주목을 받고 있다. 또한 넓은 밴드갭에 의해 가시광 영역에서 투명한 특성을 보이고, 플라스틱 기판 위에서 구부러지는 성질에 의해 플랫 패널 디스플레이나 능동 유기 발광 소자 (AM-OLED), 투명 디스플레이에 응용되고 있다. 하지만, 실제 디스플레이가 동작하는 동안 스위칭 TFT는 백라이트 또는 외부에서 들어오는 빛에 지속적으로 노출되게 되고, 이 빛에 의해서 TFT 소자의 신뢰성에 악영향을 끼친다. 또한, 디스플레이가 장시간 동안 동작 하면 내부 온도가 상승하게 되고 이에 따른 온도에 의한 신뢰성 문제도 동시에 고려되어야 한다. 특히, 실제 AM-LCD에서 스위칭 TFT는 양의 게이트 전압보다 음의 게이트 전압에 의해서 약 500 배 가량 더 긴 시간의 스트레스를 받기 때문에 음의 게이트 전압에 대한 신뢰성 평가는 대단히 중요한 이슈이다. 스트레스에 의한 문턱 전압의 변화는 게이트 절연막과 반도체 채널 사이의 계면 또는 게이트 절연막의 벌크 트랩에 의한 것으로 게이트 절연막의 선택에 따라서 신뢰성을 효과적으로 개선시킬 수 있다. 본 연구에서는 적층된 $Si_3N_4/SiO_2$ (NO 구조) 이중층 구조를 게이트 절연막으로 사용하고, 완충층의 역할을 하는 $SiO_2$막의 두께에 따른 소자의 전기적 특성 및 신뢰성을 평가하였다. a-IGZO TFT 소자의 전기적 특성과 신뢰성 평가를 위하여 간단한 구조의 pseudo-MOS field effect transistor (${\Psi}$-MOSFET) 방법을 이용하였다. 제작된 소자의 최적화된 $SiO_2$ 완충층의 두께는 20 nm이고 $12.3cm^2/V{\cdot}s$의 유효 전계 이동도, 148 mV/dec의 subthreshold swing, $4.52{\times}10^{11}cm^{-2}$의 계면 트랩, negative bias illumination stress에서 1.23 V의 문턱 전압 변화율, negative bias temperature illumination stress에서 2.06 V의 문턱 전압 변화율을 보여 뛰어난 전기적, 신뢰성 특성을 확인하였다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.4
• /
• pp.16-25
• /
• 2004

Theoretical analysis for predicting the heat transport limitation of a copper powder sintered wick heat pipe was performed. The heat pipe diameter was 8mm and water was used for working fluid. The particle diameter was classified by 5 different meshes, and each capillary pressures and heat transport limitations. thermal resistances were analyzed according to the operating temperatures, wick thicknesses and inclination angles, based on the effective capillary radius($r_c$), porosity($\varepsilon$), Permeability (K). The wick capillary limitation was increased according as the particle diameter and the wick thickness and the operating temperature were increased. As the porosity and the capillary radius were larger. then the heat transport limitation was higher. The thermal resistance was greatly increased according as the wick thickness was increased.

• Journal of the Korean Vacuum Society
• /
• v.7 no.2
• /
• pp.104-111
• /
• 1998

The InGaAs/InP quantum wells(QWs) were grown by low pressure metalorganic chemical vapor deposition and the effects of growth interruption steps on their interfacial structures were investigated by measuring photoluminescence spectra. When InP or InGaAs surface was treated under the same group V ambient, the full width at half maximum (FWHM) of the QW peak increased possibly due to the incorporation of impurities during the growth interruption time. When InP surface was treated under $AsH_3$, howerer, the PL peak showed red-shift due to the As-P exchange reaction and the change of FWHM was not remarkable. The effective thickness of InAs interfacial layer formed during $AsH_3$, treatment on the InP surface was calculated to be 1~2 monolayers. In the case of InGaAs treatment under $PH_3$, the PL peak energy and the FWHM increasied. This results suggest that $PH_3$ treatment on the InGaAs surface suppresses the incorporation of As into the subsequent InP layer and the local replacement of As by P occurs simultaneously.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.3
• /
• pp.32-36
• /
• 2016

Test equipment was designed and manufactured to evaluate thermal reaction characteristic of internal insulators of solid rocket motor. Test is allowed up to chamber pressure 2,500 psi, burn-time 100 s. A cross section of test sample part is quadrature, and various test samples can be comparable at the same time. Inner temperature of test sample can be measured by thermocouples during burning. Test was executed in condition of efficient average chamber pressure 1,000 psi, efficient burn-time 10 s and safety of equipment was confirmed. Basic data for understanding thermal characteristics of internal insulator, that is, pressure-time curve, temperature-time curve in the test sample, and thermal destruction thickness of test sample was gained successfully.

• Korean Journal of Optics and Photonics
• /
• v.8 no.4
• /
• pp.277-282
• /
• 1997

The complex refractive index of Diamond-like Carbon (DLC) thin films, which can be applied to optical devices or electrical devices, have been determined using optical methods. DLC thin films are grown on Si(100) substrates and vitreous silica substrates respectively, using the technique of plasma enhanced chemical vapor deposition (PECVD). The spectroscopic ellipsometry data($\psi$, $\Delta$) and the transmission spectra of these DLC films are obtained. These optical spectra are analyzed with the help of the Sellmeier dipersion relation and a quantum mechanically derived dispersion relation. Using spectroscopic ellipsometry data at their transparent region, the refractive index and the effective thickness of DLC films on vitreous silica are model calculated, Then the transmission spectra are inverted to yield the extinction coefficient spectra k(λ) at absorbing region. These spectra are fit to the quantum mechanical dispersion relation and the best fit dispersion constants are determined. The complex refractive indices are easily calculated with these constants. The spectroscopic ellipsometry data at the absorbing region in model calculated to give the packing densities and the degrees of surface microroughness of DLC films. Discussions are made in correlation with the growth condition of DLC films.

• Journal of the Korea Concrete Institute
• /
• v.24 no.1
• /
• pp.15-23
• /
• 2012

This paper is about proposal of a calculation method and development of an analytical program for predicting crack width and deflection in structural concrete members. The proposed method numerically calculate stresses in steel rebar using a parabola-rectangle stress-strain curve and a modified tension stiffening factor considering the effect of the cover thickness. Based on the study results, a calculation method to predict crack width and deflection in reinforced concrete flexural members is proposed utilizing effective tension area and idealized tension chord as well as effective moment-curvature relationship considering tension stiffening effect. The calculation method was applied to the test specimens available in literatures. The study results showed that the crack width and deflections predicted by the proposed method were closed to the experimentally measured data compared the current design code provisions.

• Journal of Korean Ophthalmic Optics Society
• /
• v.13 no.1
• /
• pp.65-69
• /
• 2008

Purpose: To develop a dot sight device for a sighting shot using the doublet reflector. Methods: We designed the singlet reflector and the doublet reflector by Sigma 2000 program and compared the one to the other. Results: In analysis of finite ray aberration, we could confirm that it has the effective field of view with the free-parallax which is 3.3 times wider than the existing dot sight device using the singlet reflector. If you use the doublet reflector, the central thickness of optical system become more than two times bigger than the existing one. As a result, when the image of a target object is made on the observer's retina, if you make the first side's radius of curvature equal with the second one as the case of the singlet reflector, changes in magnification are appeared. To conquer this problem, we had to make be satisfied with the afocal condition in the case of doublet reflector. Conclusions: we could develop the dot sight device for a sighting shot using the doublet reflector which has the effective field of view with the free-parallax which is 3.3 times wider than the existing dot sight device using the singlet reflector.

• The Journal of the Acoustical Society of Korea
• /
• v.34 no.6
• /
• pp.470-478
• /
• 2015

A heuristic method treating a layered ocean bottom in a ray modeling is to use the plane wave reflection coefficient for multiple-layered structure, named an one-layer assumption in this paper. We examine the validity of one-layer assumption in the case of two-layered ocean bottom, and obtain a simple inequality condition depending on the sound speed ratio, the ratio of layer thickness to source-receiver range, and the grazing angle of first reflected ray. From this inequality condition, it is shown that an one-layer assumption can be applicable to ray propagation problems at mid frequencies. Finally, numerical experiments are performed in the ocean environment similar to the East Sea in Korea. Incoherent transmission loss is calculated by the geometrical beam model with the plane wave reflection coefficient for multiple-layered ocean bottom and compared with the result of SNUPE 2.0, which is a parabolic equation package developed in Seoul National University.