• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.410-415
• /
• 2001

Hydraulic mounts have been used as an alternative to the conventional rubber mounts for they can provide more desirable stiffness and damping properties which may vary with frequency and excitation amplitude. Although a lumped-parameter non-linear model of the hydraulic mount developed by a simple fluid dynamic analysis can be successfully used for representing the inertia track dynamics, a linear model is still preferred. In this paper, an analytic technique for making a linear model of the hydraulic mount is proposed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.04a
• /
• pp.715-716
• /
• 2014

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.10a
• /
• pp.328-329
• /
• 2009

Air-Damping Mount is proposed to compromise between performance and weight & cost. The design of Air-Damping Mount was based on the specification from the engine mounting system analysis of a small car. To verify it's feasibility, R&H test was done on the small car and it is proven that Air-Damping Mount shows the performance between hydraulic mount and rubber mount.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.5
• /
• pp.393-399
• /
• 2003

Hydraulic mounts show strong1y frequency-dependent stiffness and damping characteristics in low frequency range, which result from so called inertia track dynamics. A lumped mass has been incorporated in several mechanical models of the literature to take the inertia effect of the fluid in the track into consideration. Although complex s%illness by the mechanical model showed good agreements with the measured values, there exists a critical pitfall. In this paper, the shortcomings of mechanical models with lumped mass for hydraulic founts are clearly identified by illustrating actual measurements of the stiffness parameters for a hydraulic mount. It is conclusively discussed that the inertia effect of the fluid flow through the circular track is significant but latent. As an alternative to the mechanical model, a hydraulic model is claimed to be used for further dynamic analysis of engine/mount system or whole car system.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.2 s.173
• /
• pp.370-377
• /
• 2000

This paper presents a mixed-mode type ER(electro-rheological) engine mount, and its vibration control performance for a passenger vehicle is presented. The field-dependent yield stress of a transfo rmer oil-based ER fluid is empirically distilled in both shear and flow modes. This is then incorporated with the governing equation of motion of the proposed mixed-mode(shear mode plus flow mode) type engine mount. The damping force is analyzed with respect to the intensity of the electric field and design parameters such as electrode gap. Subsequently, the ER engine mount which is equivalent to the conventional hydraulic engine mount in terms of the damping level is designed and manufactured. Both computer simulation and experimental test are undertaken in order to evaluate vibration isolation performance. In addition, this performance is compared with that of the conventional hydraulic engine mount.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.27 no.1
• /
• pp.80-86
• /
• 2017

This paper describes switching method of the cross-sectional area of the fluid passage way to improve the performance of a hydraulic engine mount with an inertia track and a decoupler. The mount has nonlinear dynamic characteristics depending on the vibrational frequency and amplitude. For the convenience of analysis, two linear motion equations were derived on the basis of the mechanical model according to the low-and high-frequencies. The properties of the transmissibility and dynamic stiffness derived from the equations were investigated according to switching the cross-sectional area of the inertia track and decoupler. Switching method of the cross-sectional area can be derived from the transmissibility plot. In comparison between transmissibility of passive and switchable mounts with an inertia track and a decoupler, the performance of the switchable mount is improved greatly than the passive mount. The resonant peak is remarkably reduced in the high frequency region.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.4
• /
• pp.291-298
• /
• 2011

According to the developments of automobile industry, the technology to enhance noise, vibration and harshness(NVH) performance has been studying in a point of view of ride comfort and quietness. Especially the use of computer aided engineering(CAE) simulation tools such as finite element(FE) analysis allows engineers to efficiently evaluate NVH performance. This paper presents the method to bulid FE models for full vehicle including engine, transmission. suspension and steering system, also to evaluate vibration performance of full vehicle. The full vehicle model, which is discussed, is correlated with the result of the frequency response measurement in the case of the car shake performance for high speed driving.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.4
• /
• pp.110-120
• /
• 2000

In order to improve the vibration characteristics of mid sized passenger car automatic transmission at idle experimental and theoretical studies have been carried out. Idle shake in "D" range occurs by various reasons such as characteristics of body bending resonance between subsystems and engine mounts etc. Using full vehicle finite element analyses and modal tests we introduce the way to reduce the idle shake in the early design stage. It shows that the exciting forces are the 2nd order torque and force of engine. A powertrain system modes in "D" range are entirely effected by the additional boundary conditions of drive line. As a result the frequencies of subsystems are arranged to be lined up at the idle frequency range in order to avoid the resonances with subsystems To reduce the idle shake mounts of radiator are tuned to act as a dynamic damper to 1st bending frequency of the body. In addition a hydraulic mount which is optimized by Phase Shift Method is applied to the rear engine mount.e rear engine mount.