• Journal of KSNVE
• /
• v.6 no.1
• /
• pp.35-44
• /
• 1996

This paper presents a new type of fuzzy-sliding mode controller for robust tip position control of a single-link flexible manipulator subjected to parameter variations. A sliding mode controller is formulated with an assumption that imposed parameter variations are bounded so that certain deterministic performance can be guaranted. In the design of the sliding mode controller, so called moving sliding surface is adopted to minimize the reaching phase and thus mitigate system sensitivity to the variations. The sliding mode controller is then incorporated with a fuzzy technique to reduce inherently ever-existing chattering which is impediment in position control of flexible manipulators. A set of fuzzy parameters and control rules are obtained from a relation between predetermined sliding surface and representative points in the state space. Computer simulations are undertaken in order to demonstrate superior control performance of the proposed methodology.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.383-386
• /
• 1996

In this paper, we propose a design method and control law for plannar type two-link flexible manipulator. In designing flexible links, we use Rayleigh's principle. To control flexible manipulator, input distribution controller is used, which is primarily on the basis of nonlinear variable structure control(VSC). The simulation results are also shown.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.7-11
• /
• 1991

The adaptive control of flexible joint manipulator is the focus of this paper. The full order flexible joint manipulator dynamic system does not allow the determination of a feedback linearization control as for rigid manipulators. This drawback is overcome by a model order reduction based on a singular perturbation strategy. The full order flexible joint manipulator dynamic model is adopted for derivation of the adaptive control law to damp out the elastic oscillations at the joints. It is shown that the joint position error will converge to zero asymptotically and that other signals remain bounded without precise knowledge of parameters of the manipulator and its joint flexibility.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.30-33
• /
• 1991

The natural frequency of an one-link flexible robot manipulator may be varied due to many kinds of causes and this natural frequency is regarded as the uncertain element. Utilizing measured state the robust controller is designed for bounding every system response within a certain neighborhood of the zero state.

• 제어로봇시스템학회:학술대회논문집
• /
• 1989.10a
• /
• pp.200-205
• /
• 1989

The performance of conventional robot arms is inhibited by trade-off between speed and accuracy. Because these systems measure only joint angles, in spite of slow speed, they must rely on a stiff structure in order to attain positioning accuracy. Lightweight links would allow faster motion, but their flexibility would also produce positioning errors. This research is involved with the development and evaluation of an End-point Control System whose major goal is to compensate for link deflections and thus mitigate the speed versus accuracy conflict in conventional manipulator.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.260-265
• /
• 1992

This paper presents an adaptive control scheme for flexible joint robot manipulators. This control scheme is based on the Lyapunov direct method with the arm energy-based Lyapunov function. The proposed adaptive control scheme uses only the position and velocity feedback of link and motor shaft. The adaptive control system of flexible joint robots is asymptotically stable regardless of the joint flexibility value. Therefore, the assumption of weak joint ealsticity is not needed. Also, joint flexibility value is unknown. Simulation results are presented to show the feasibility of the proposed adaptive control scheme.

• 제어로봇시스템학회:학술대회논문집
• /
• 1990.10a
• /
• pp.18-23
• /
• 1990

In this paper, the dynamic modeling and a tip-position controller of a single-link flexible manipulator are developed. To design the controller of a flexible manipulator, at first, it is required to obtain the accurate dynamic model of manipulator describing both rigid motion and flexible vibration. For this purpose, FEM(Finite Element Method) and Lagrange approach are utilized to obtain the dynamic model. After obtaining the dynamic model of a single-link manipulator, a controller which computes the input torque to perform the desired trajectory is developed using neural network.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.321-321
• /
• 2000

This paper presents a sliding mode controller based on variable structure for the tip position control of a single-link flexible manipulator. Dynamic equations of a single-link flexible manipulator are derived from the Euler-Lagrange equation using a Lagrangian assumed modes method based on Bernoulli-Euler Beam theory. Simulation results are presented to show the validity of the system modeling, controller design.

• Proceedings of the Korea Institute of Convergence Signal Processing
• /
• 2001.06a
• /
• pp.145-148
• /
• 2001

본 논문에서는 자기구성 신경회로망을 이용하여 3축 매니퓰레이터의 궤적제어기를 설계한다. 궤적 제어는 경유점을 정하고 각 경유점에 대한 역기구학을 적용하는 제어기로서 본 논문에서는 역기구학의 해를 자기구성 신경회로망을 통해 해결하는 제어기를 설계하고자 한 다. 또한 제어기에서의 은닉층의 활성화 함수는 가우 시안 함수를 사용하고, 은닉층의 파라미터는 오차를 기초로 하여 자동적으로 최적의 파라미터 값을 구함으로 서 유연한 궤적 제어가 되도록 한다.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.45 no.1
• /
• pp.123-130
• /
• 1996

Due to high payload capacity and high length-to -cross-section ratio requirements, long-reach manipulator systems are expected to exhibit significant structural flexibility. To avoid structural vibrations during operations, various types of input shaping filtering methods have been investigated. A robust notch filtering method and an impulse shaping filtering method were investigated and implemented. In addition, two very different approaches have been developed and compared. One new approach, referred to as a