• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.977-981
• /
• 1996

A load sensing hydraulic system is widely used to military and commercial mobile applications fur its high running efficiency. Although concept and general control schemes are well known, the poor maneuverability of simultaneous multioperation of actuators still remains to be solved. In this paper, a new control algorithm is proposed to prevent the saturation of the system in such operating conditions, in which the total required flowrate of actuators may exceed the pump supply flowrate. The effectiveness of the proposed algorithm is verified through experiments.

• Journal of the Korean Society for Precision Engineering
• /
• v.9 no.4
• /
• pp.126-135
• /
• 1992

Up to now, there has been a lot of researches on the sliding mode control which has the insensitive characteristics to the variations of plant parameters, nonlinearities and external disturbances. One difficulty in applying the sliding mode control is the need for the knowledge of the full-state vector. The use of state observer is a natural step towards the relaxation of this condition. However, the exact plant-modeling is assumed to be known. Recently, there has been a remarkable advance in the microprocessor and one can construct the controller which could not realize due to hardware restriction in the past. Therefore in this paper, the PID sliding mode controller which has only one output feedback signal is suggested by means of microprocessor and the performance of electro-hydraulic servosystem compensated with this controller is proved.

• Journal of the Korean Society for Precision Engineering
• /
• v.8 no.3
• /
• pp.64-72
• /
• 1991

This paper deals with the state estimator and controller. All state variables' feedback in the system were used to improve electro hydraulic servo sysem were used to improve electro hydraulic servo system's responese charact- eristics. Many gains of the state variables'and estimator's are produced by the algebraic Riccati equation, and every state variables'optimal gain and estimator gain is selected by trial and error method. For the designed estimator performance's examination, this paper simulate the time response for the step input, the reduced velocity output in subjected to load torque, and the time response for the step input in changing the inertiamoment.

• The Journal of Korea Robotics Society
• /
• v.5 no.2
• /
• pp.160-168
• /
• 2010

In order to achieve a force controller with high performance, an accurate torque servo is required. However, the precise torque servo for a double vane rotary actuator system has not been developed till now, due to many nonlinear characteristics and system parameter variations. In this paper, the torque servo structure for the double vane rotary actuator system is proposed based on the torque model. Nonlinear equations are set up using dynamics of the double vane rotary hydraulic actuator system. Then, to derive the torque model, the nonlinear equations are linearized using a taylor series expansion. Both effectiveness and performance of the design of torque servo are verified by torque servo experiments and applying the suggested torque model to an impedance controller.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.5 no.3
• /
• pp.15-22
• /
• 2008

The road simulators have become common tools within the automotive industry for evaluation of vehicle and vehicle system durability performance. These simulators need appropriate input signal generation algorithms to realize the actual driving conditions due to non-linear vehicle and test rig behaviour. Although somewhat unconventional from a control standpoint, the iteration approach has proven to be a very effective method for control of complex, multiple degree-of-freedom systems where the tracking parameter is known a priori. In this paper, the road profile replication algorithm is verified by applying Belgian road to the developed road simulator. The simulation and experimental results are included to evaluate the performance of this simulator. This road simulator provides considerable savings in cost, development time, and testing risk during developing automotive components.

• Journal of the Institute of Convergence Signal Processing
• /
• v.10 no.1
• /
• pp.93-99
• /
• 2009

The fuzzy control, neural network and genetic algorithm(GA) are algorithms to make the intelligence of system more higher. In this paper, we optimized the fuzzy controller using a genetic algorithm for desire response. Also a compensated fuzzy controller has dual rules. One control rule used to decrease the overshoot and rise time occurring in transient response region and another fuzzy control rule use to decrease the steady state error and rapildy to converge at the convergence region. GA is necessary to optimal the exchange time of the two fuzzy control rule base. Fuzzy-GA controller have a process of reproduction, crossover and mutation and we experimented by hydraulic servo motor control system We could observe that compensated Fuzzy-GA controller have good control performance compare to the fuzzy control technique have two rule base table.

• Journal of Drive and Control
• /
• v.16 no.4
• /
• pp.93-100
• /
• 2019

Nuclear and thermal power plants must provide the turbines with an appropriate degree of high temperature and high pressure steam, to produce the optimum electricity. Additionally, in the event of system and power system failure during electrical production, the steam is immediately disabled, to protect the turbines and generators rotating at high speed. The plant thus uses a special steam control valve system for turbine control, which is opened by force of the hydraulic servo actuator and closed by a large steel spring force. In this study, the causes of failure of the turbine control valve system, a key device of the power plants, were analyzed, and the causes of failure were improved relative to reliability of the equipment.

• Aerospace Engineering and Technology
• /
• v.4 no.2
• /
• pp.21-26
• /
• 2005

In airframe structural tests, a control system which has many control channels and a data acquisition system which has many data acquisition channels are used. The more it is used many channels in airframe structural test, the more hardware resources are added in test system. Before test load is applied in test article, test engineer must check test system and components. Therefore, many problems which be likely to happen to system can be minimized. The checking method of test system and components is calibration verification. In this paper, it is described that calibration verification concept and method in relation to airframe structural test controller components.(MTS Aero90 Multifunction Input Output Processor and 497.22 Dual DC Conditioner)

• Journal of Navigation and Port Research
• /
• v.42 no.3
• /
• pp.237-244
• /
• 2018

When underwater rubble leveling work is carried out by a robot, real-time information on the topography around the robot is required for remote control. If the topographical information with respect to the current position of the robot is displayed as a 3D graphic image, it allows the operator to plan the working schedules and to avoid accidents like rollovers. Up until now, the topographical recognition was conducted by multi-beam sonars, which were only used to assess the quality before and after the work and could not be used to provide real-time information for remote control. This research measures the force delivered to the bucket which presses the mound to determine whether contact is made or not, and the contact position is calculated by reading the cylinder length. A variable bang-bang control algorithm is applied to control the heavy robot arms for the positioning of the bucket. The proposed method allows operators to easily recognize the terrain and intuitively plan the working schedules by showing relatively 3-D gratifications with respect to the robot body. In addition, the operating patterns of a skilled operator are programmed for raking, pushing, moving, and measuring so that they are automatically applied to the underwater rubble leveling work of the robot.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.13 no.3
• /
• pp.334-341
• /
• 2003

In this paper, we proposed a recurrent time delayed neural network(RTDNN) controller which compensate a output of neural network controller. Even if learn by neural network controller, it can occur an bad results from disturbance or load variations. So in order to adjust above case, we used the fuzzy compensator to get an expected results. And the weight of main neural network can be changed with the result of learning a inverse model neural network of plant, so a expected dynamic characteristics of plant can be got. As the results of simulation through the second order plant, we confirmed that the proposed recurrent time delayed neural network controller get a good response compare with a time delayed neural network(TDU) controller. We implemented the controller using the DSP processor and applied in a hydraulic servo system. And then we observed an experimental results.