• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1987.06a
• /
• pp.57-60
• /
• 1987

근래에 들어 축의 고속회전이 요구되고 윤활제로 물이나 액체금속과 같은 동점성계수가 낮은 윤활제가 사용됨에 따라 베어링내의 유동은 층류상태를 벗어난 난류상태에 이르고 있다. 이와같이 고속에서 사용되는 저어널베어링에서의 윤활제의 유동은 더욱 복잡하게 되어 이들에 대한 정확한 특성을 예측하기 위한 연구가 필요하게 되었다. 최근에는 열유체윤활에 대한 연구가 행하여지고 있으나 저어널베어링의 온도특성에 대한 실험적 연구는 부족한 상태이다. 그리고 저어널의 하중을 지지하는 유막내의 압력에 대한 실험을 보면 거의 베어링면에서 국부적으로 측정하므로 유막에서 발생하는 압력의 분포를 정확히 알기는 어렵다. 본 연구에서는 저어널의 중앙단면에 압력계를 부착하여 연속적인 압력분포를 측정하고 베어링내면의 온도분포를 측정하며 편심율과 위상각, 배유량을 측정하여 저어널베어링의 성능특성을 예측하기 위한 실험자료를 제공하는 것을 목적으로 한다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.5
• /
• pp.698-705
• /
• 1986

The dynamic behaviour of bearing-rotor system with flexible and damped supports is systematically investigated. To find out the obvious trend of the influence of the external damping on the resonance peak of a rolling bearing-rotor system and on the stability linit of a cylindrical journal bearing-rotor system, some important characteristic design parameters are derived. Those are the dimensionless stiffness and damping ratio of the external damping refered to the rotor stiffness. For an optimal design of the external damping a relation between the stiffness and damping coefficients can be obtained from the dynamic analysis of the whole system.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.4
• /
• pp.9-17
• /
• 1994

Effect of Newtonian and non-Newtonian oils on minimum ol film thickness in engine journal bearing were investigated at various oil viscosities. The influence of oil viscosity and engine operating conditions on minimum oil film thickness of main bearing and con-rod bearing was examined. Minimum oil film thickness for Newtonian oils increased uniformly with kinematic viscosity. But the correlation between kinematic viscosity and minimum oil film thickness was very poor for non-Newtonian oils. According to the straight-line regression analysis for non-Newtonian oils, high temperature high shear viscosity at 1 $1{\times}10^6Sec^{-1}$, $150^{\circ}C$ increase the coefficient of determination from 0.41 to 0.77. Con-rod bearing showed better correlation between minimum oil film thickness and engine operating conditions than main bearing.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1986.11a
• /
• pp.42-46
• /
• 1986

회전축계가 위험한 공진 또는 불안한 상태를 나타내지 않고 조용하고 안정된 운전상태를 유지하려는 목적은 축의 휨강성, 몸체형상, 베어링의 크기 및 형상과 같은 설계변수를 최적화하는 것으로 이루어질 수 없는 경우가 빈번하다. 이런 경우에는 베어링 외부에 작용하는 "외부댐핑"을 이용하여 진동문제를 근본적으로 개선할 수 있다. 이를 위하여 베어링 외부에 별도로 설계한 스프링과 댐퍼를 설치한다. 본 연구에서는 윤활이론에 따라 명확히 계산되고 그 신빙성이 실험적으로 검증된 "동압유막 댐퍼"의 감쇄계수를 이용하여 외부댐핑을 갖는 회전축-구름베어링\ulcorner와 회전축-저어널 베어링계의 진동특성을 해석하고 회전축-구름베어링계의 실험적 모델을 제시하고자한다. 또한 해석결과와 실험을 토대로 회전축계의 진동특성에 미치는 특성수 및 설계변수를 명확히 도출하여 동특성을 고려한 회전축계의 최적 설계에 기여하고자 한다.축계의 최적 설계에 기여하고자 한다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.1
• /
• pp.120-126
• /
• 1991

An expanded scheme of a direct numerical solution method for solving the Navier-Stokes equation considering the modified boundary conditions for gas lubrication with ultra low clearance at high .LAMBDA. region is presented. Many examples are calculated by this scheme and their results are compared to the previous solutions using P$^{2}$H$^{[-992]}$ . This scheme has the advantages of fast calculation time and stable convergence in high .LAMBDA. region, and gives very good results in the case of fluid film thickness discontinuity.

• Journal of Advanced Marine Engineering and Technology
• /
• v.19 no.4
• /
• pp.61-71
• /
• 1995

Nowadays the thin-walled metal bearing, which is made seperately from the bearing housing and has the ratio of wall thickness/bearing diameter being less than 1/30, are used in many newly developed large-sized slow speed diesel engines for the purpose of upgarding lubication performance and easy maintenance according to the trends of increasing output per cylinder and lowering engine speed. The type of this bearing has been used generally in many small-sized high speed engines applied for automobile, high speed craft and industrial power generation systems since 1950s. But the tranditional thick-walled bearings, whice are linned white metal on the bearing housing directly, have been installed on the large and slow speed engines until 1990s due to the easy manufacturing procedures. In this study we have calculated optimum dimensions of the metal bearing, fabricated special zigs for crush measurement, model test machine, 2 sets of specimens.(crosshead pin bearing, $\phi$818*552*20mm) for B & W 6S70MC(20, 940*88rpm), and evaluated metal constact phenomena of white metal, its friction coefficient, temparature rise through the model test and field performance test.

• The Journal of the Acoustical Society of Korea
• /
• v.32 no.3
• /
• pp.208-213
• /
• 2013

To get vibration responses, a camshaft is modelled as an unbalanced multiple rotor bearing system. Because of complex geometry and complicated load conditions, the finite element method is used. After the finite element equation of the system is constructed, Newmark's method is used to get the vibration responses. Whirl vibration responses of a V-8 engine camshaft are estimated and compared with measured responses. After the fluctuating stresses are obtained, fatigue analysis is performed based upon the modified Goodman's equation. Stress concentration effects are considered. In the whirl vibration of camshafts, the bending effect is dominant, and the bending deformation is dependent upon the span length between the adjacent bearing journals. For high speeds, the fluctuations of excitation forces are large, and it is known that nonlinear time varying bearing coefficients should be used for analysis.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.8
• /
• pp.521-529
• /
• 2017

Three-dimensional flow characteristics within a high-acceleration first-stage turbine vane passage has been investigated in a newly-built vane cascade for propulsion. The result shows that there is a strong favorable pressure gradient on the vane pressure surface. On its suction surface, however, there exists not only a much stronger favorable pressure gradient than that on the pressure surface upstream of the mid-chord but also a subsequent adverse pressure gradient downstream of it. By employing two different oil-film methods with upstream coating and full-coverage coating, a four-vortex model horseshoe vortex system can be identified ahead of each leading edge in the cascade, and the separation line of inlet boundary layer flow as well as the separation line of re-attached flow is provided as well. In addition, basic flow data such as secondary flow, aerodynamic loss, and flow turning angle downstream of the cascade are obtained.