• Composites Research
• /
• v.12 no.2
• /
• pp.62-69
• /
• 1999

During fatigue loading of composite materials, damage accumulation can be monitored by measuring their material properties. In this study, fatigue modulus is used as the damage index. Fatigue life of composite materials may be predicted analytically using damage models which are based on fatigue modulus and resultant strain. Damage models are propesed as funtions of applied stress level, number of fatigue cycle and fatigue life. The predicted life was comparable to the experimental result obtained using E-glass fiber reinforced epoxy resin materials and pultruded glass fiber reinforce polyester composites under two-stress level fatigue loading.

• Composites Research
• /
• v.31 no.5
• /
• pp.186-191
• /
• 2018

Condition and properties of composites with different chemical structure of epoxy matrix were observed after saline solution treatment. Epoxy was used as matrix and the flexibility was controlled by using 2 typed-epoxies and 3 types hardeners (amine, acid anhydride and amide). Saline water treatment was conducted with 6 wt% NaCl solution at $60^{\circ}C$ for 0, 15, and 30 days. Cross section was observed and interfacial and mechanical and properties was evaluated. Amine type exhibited the highest crosslinking density and mechanical and interfacial properties whereas water absorbance was lowest. It is because that the water molecules can be hardly penetrate into the epoxy matrix or the interface between epoxy and glass fiber and it leads to saline water resistance of composites.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.4A
• /
• pp.775-785
• /
• 2006

This study focused on the development of surface deformations of GFRP rebars with a better bond characteristic for reinforcing concrete, and simultaneously, of GFRP rebars with more simple and economic production process. This research paper describes a development and bond performance of GFRP rebar with molded deformations, which is composed of polymer resin and milled glass fiber. To determine proper mix ration of milled fibers, material test of hardened epoxy and pullout tests of GFRP rebar with various mix ratio were conducted. The test results indicate that the new strategy of using a mixture of epoxy resin and milled fiber could be successfully applied to a surface structure of GFRP rebar to enhance bond with concrete. The bearing resistance of the ribs was further enhanced by the milled fibers at mechanical and environmental loading state.

• Composites Research
• /
• v.31 no.1
• /
• pp.30-36
• /
• 2018

The curing behavior of glass fiber reinforced epoxy prepregs based on Bisphenol-A (BPA) was studied by differential scanning calorimetry (DSC). The total heat of reaction(${\Delta}H_{total}=280.3J/g$) was determined based on the results of the dynamic heating scanning experiments. Isothermal experiments were carried out at $110{\sim}130^{\circ}C$, and it was observed that the maximum conversion and the maximum reaction rate were increased as temperature increased. Also Kamal equation was applied to analyze autocatalytic reaction of epoxy prepregs. The higher temperatures, the greater reaction rate constants ($k_1$, $k_2$). Theoretical values were calculated by these reaction rate constants and compared with experimental values. And it was confirmed that they were in reasonable agreement. At the beginning of the reaction, the experimental data and theoretical prediction were shown the same tendency, but at the end of reaction, the experimental data were smaller than theoretical predicted values due to reaction rates controlled by diffusion.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2003.05a
• /
• pp.514-519
• /
• 2003

치수효과는 콘크리트나 암석과 같은 quasi-brittle 재료들의 물리적 특성에 영향을 미친다. 모든 재료의 경우에 체적이 크면 흠이 클 수 있다. 구조물의 섬유 묶음 크기가 증가하면, 섬 유 강도가 감소하는 현상을 흔히 경험해 왔다. 복합재료내의 강도 분배와 치수사이의 관계를 특성 짓는 효과적인 방법은 아직 완전하지 않다. 본 논문에서는 경험에서 얻어진 Filament Wound 튜브에 사용되는 유리 섬유와 에폭시의 인장강도 감소비율 실험데이터로 얻은 그래프로부터 Crasto와 Kim의 일방향 보강된 AS4/3501-6복합재료의 90$^{\circ}$방향 인장강도에 대한 실험결과로부터 복합재료 봉구조재의 강도 치수효과를 증명하였다.

• Electrical & Electronic Materials
• /
• v.1 no.2
• /
• pp.115-125
• /
• 1988

지금까지 발전기 전동기 및 전력용 변합기와 같은 중전기에 사용되고 있는 복합절연재료인 유리섬유 강화프라스틱은 단가가 높고, 기계적 특성이 비등방성이며 기게적 응력이나 서어비스 중에 계면보이드의 발생으로 문제성이 제기되어 왔다. 이러한 결점을 해소하기 위하여 플레이크상의 필라에 대한 연구가 활발히 진행되고 있다. 본 연구에서는 대표적인 플레이크상 재료인 마이카를 이용하여 현재 대형 발전기나 전동기의 고정자 권선 절연용으로 연구 개발되고 있는 마이카 페이프/에폭시 복합재료를 제작한 후, 이 재료의 전기적 및 기계적 특성과 최적 제작조건 등에 실험적으로 고찰하였다. 특히 아미노 실란 게면 결합제를 필라에 적용하여 시료의 전기적 및 기계적 특성에 미치는 효과를 검토하였다.

• Aerospace Engineering and Technology
• /
• v.13 no.1
• /
• pp.20-26
• /
• 2014

In this paper, yield stress, tangent modulus and failure strain were varied to ascertain the influence of impact response such as impact force histories and residual energy. And the buckling behavior of FML(Fiber Metal Laminates) were analyzed using numerical method. A number of analyses on FML and aluminum panel were conducted for shear and compression loading to compare the capability of stability. And to evaluate the static performance, static analysis has performed for box beam structure. Low-velocity impact analysis has performed on FML made of aluminum 2024 sheet and glass/epoxy prepreg layers. And the buckling and static performance of FML have been compared to aluminum using the analysis results. For the comparison of structural performance, similar analyses have been carried out on monolithic aluminum 2024 sheets of equivalent weight.

• Journal of Adhesion and Interface
• /
• v.21 no.2
• /
• pp.65-70
• /
• 2020

Epoxy adhesive was mainly used to combine different composite materials. Epoxy adhesive was a typical thermosetting resin that can be bonded by changing from a linear structure to a three-dimensional network structure by curing reaction of epoxy and hardener. The curing conditions of epoxy adhesive were different with different types of hardener such as mixing ratio, curing time, and temperature. These curing conditions affected to the adhesive property of epoxy adhesive. In industry, it was difficult to proceed the applying epoxy adhesive and combining two parts immediately. The adhesive property decreased by humidity and pre-curing of epoxy adhesive in waiting time between two processes. In this paper, the glass fiber reinforced composite (GFRC) was combined with epoxy adhesive and adhesion property between epoxy adhesive and GFRCs was evaluated using single lap shear test. The different waiting times and humidity conditions were applied to epoxy adhesive in room temperature and adhesive property decreased as the waiting time increased. In small amount of humidity, the adhesive property increased because a small amount of moisture in the surroundings accelerated the curing reaction. In certain amount of humidity, however, the adhesion property decreased.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.3
• /
• pp.177-183
• /
• 2023

Various failure modes occur in the concrete beams reinforced with GFRP(Glass Fiber Reinforced Plastic) under initial condition and repairing patterns. In this study, the failure behaviors of concrete beams restrengthened with GFRP sheet with slightly higher elastic modulus than concrete were investigated. For the tests, concrete beams with 24 MPa were manufactured, and the effects of initial notch, overlapping, end-strip reinforcement, and fiber anchors were analyzed on failure load. The cases of GFRP overlap around notch and the initial notch showed increasing failure loads similar to those of normal restrengthened case since the epoxy of the saturated GFRP sufficiently repaired the notch area. Compared to the control case without restrengthening of GFRP, the concrete with initial notch showed 0.78 of loading ratio and normal restrengthening showed 4.43~5.61 times of increasing ratio of failure loading, where interface-debonding from flexural crack were mainly observed. The most ideal failure behavior, break of GFRP, was observed when end-strip over 1/3 height from bottom and fiber anchor were installed, which showed increasing failure load over 150 % to normal restrengthening.

• Journal of Adhesion and Interface
• /
• v.21 no.1
• /
• pp.27-33
• /
• 2020

Adhesion property of epoxy adhesive was evaluated with different surface roughness of glass fiber reinforced composite (GFRC) and optimized condition of surface roughness was confirmed. Different sizes of alumina (Al2O3) particles were blasted to GFRC to control surface roughness of GFRC using sand blasting method. The surface roughness was measured and quantified via surface roughness tester. Contact angle was measured using four types of different solvents. Surface energies and work of adhesion between epoxy adhesive and GFRCs were calculated with different surface roughness of GFRC. Adhesion property between epoxy adhesive and GFRCs was evaluated using single lap shear test and adhesion property increased with surface roughness of GFRC. The fracture surface of GFRCs was observed to evaluate adhesion property. Finally, the optimized roughness condition of GFRCs was confirmed.