• 한국가스학회지
• /
• 제13권4호
• /
• pp.15-21
• /
• 2009

섬유강화 복합재료는 비강성과 비강도등의 우수한 기계적 성질을 나타내므로 구조물의 경량화가 요구되는 여러 산업분야에서 널리 사용되고 있다. 이러한 복합재를 이용한 압력용기는 무게를 경량화함으로써 에너지를 절약할 수 있고 강한 내식성을 가지고 있기 때문에 장기간 사용에 유리하다. 본 연구에서는 유한요소법과 ANSYS 반응표면법을 이용하여 안정성 판단의 기준으로 Von-mises 항복 기준, Tasi-hill이론, 응력비를 만족시킬 수 있는 E-glass/epoxy로 필라멘트 와인딩된 CNG차량복합재 압력용기 적층판의 최적설계 모듈을 개발하였다.

• 한국자동차공학회논문집
• /
• 제8권6호
• /
• pp.208-219
• /
• 2000

In this study, static axial crush tests were performed with the new aluminum/GFRP hybrid tube. Glass/Epoxy prepregs were wrapped around an aluminum tube and co-cured. The failure of the hybrid tube was stable and progressive without trigger mechanism, and specific energy absorption was increased to the maximum of 33% in comparison with the aluminum tube. Effective energy absorption is possible for an inner aluminum tube because a wrapped composite tube constrains the deflection of an aluminum tube. The failure of a hybrid composite tube was stable without trigger mechanism because the inner aluminum tube could play the role of the crack initiator and controller. Mean crushing load could be calculated by modifying the plastic hinge collapse model for hybrid materials. The predicted results by this analytical model showed good agreement with the experimental results. It can be said that Aluminum/Glass-Epoxy hybrid tube is suitable for the vehicle front structure because this hybrid tube shows effective energy absorption, easy production, and simple application capability for RTM process.

• 해양환경안전학회지
• /
• 제5권2호
• /
• pp.15-26
• /
• 1999

The marine structures with sea water cooling system always expose to the oceanic atmosphere. Therefore, the protection of the equipments is very important. To investigate the effectiveness of advanced composite materials for the application in offshore environments, the tensile test, hardness test, undercutting property test, permeance test and the friction and wear test were carried out by using various applicable coating materials. The main results obtained can be summarized as follows; 1. The micro-hardness of the Archcoat 502B showed the highest value. 2. The coefficient of friction of the Rigspray coating at the speed of 2.21m/sec showed the lowest value, and that of the Archcoat 502B coating at 1.08m/sec and 0.18m/sec indicated the lowest values. 3. The wear mass at the speed of 0.18m/sec and 1.08m/sec in dry condition showed the smallest values. 4. The Archcoat 502B coating is fitted to the dynamic instruments in the range of low speed and middle speed. Rigspray coating is fitted to the dynamic instruments in the range of high speed. 5. The wear mass of five kinds of coating materials at the range of low speed was very small, and those of the Archcoat S02B, Archcoat 402B and Rigspray coating at high speed range were quitely smaller than those of the Modified Epoxy and Tar Epoxy.

• 한국전기전자재료학회논문지
• /
• 제11권3호
• /
• pp.174-180
• /
• 1998

In this work, the properties of FRP, which is applied recently in the composite insulating materials, by thermal treatment were investigated. The specimens were epoxy glass laminates fabricated by thermal press method and had the volume content of 46[%] cutted $45^{\circ}C$ in the fiber direction and 1.0[mm] thickness. The experimental results showed that the amount of weight loss, wettability, surface potential, and surface resistivity increased up to 200[$^{\circ}C$] as a function of temperature. Usually, most degradations caused the hydrophilic to decrease the contact angle. But, in this work on thermal-degradated FRP, we can confirm the introduction of hydrophobic properties by cross-linking and the ablation of polar small-molecules rather than chain scission and oxidation. Finally, weight loss and contact angle increased. These phenomena show the existence of hydrophobic surface. With the change to the hydrophobic surface and the electrical potential and resistivity on FRP surface increased. But, the dielectric properties and tensile stength are decreased.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.381-388
• /
• 2003

The material deficiencies in the form of pre-existing defects can initiated cracks and fractures. The stress distribution and fatigue crack initiation life of engineering materials may be associated with the size, the shape and the relative location of defects contained in the component. The objective of this study is to investigate the effect of arbitrarily located hole defect around the rivet hole of a wing section in monolithic aluminum and Al/GFRP laminates under cyclic bending moment during a service load. The stress distribution and the fatigue crack initiation behavior near a rivet hole of on the relationships between stress concentration factor ($K_t$) and relative position of defects were considered. The test results indicated the features of different stress field. Therefore, the stress concentration factor ($K_t$) and the fatigue crack initiation behavior was illustrated different behavior according to each position of hole defect around the rivet hole in monolithic aluminum and Al/GFRP laminates.

• Composites Research
• /
• 제32권6호
• /
• pp.349-354
• /
• 2019

복합재료 중심인장선의 구성은 강화재로 사용되는 탄소섬유 및 유리섬유와 기지재로 사용되는 속경화 열경화성 에폭시로 되어있다. 본 연구에서는 가공송전선의 복합소재 중심인장선(ACCC)에 사용되는 에폭시 경화물에 대하여 분석하였다. 다관능성 에폭시 중 4관능성 에폭시(PA 806)을 사용하고 MNAn, HHPA 두가지 경화제 및 경화 촉진제를 사용하여 에폭시 경화물을 만들고 이를 분석하였다. 경화제의 종류 및 경화 촉진제의 함량에 따른 최적조건을 도출하였다.

• 대한기계학회논문집
• /
• 제12권4호
• /
• pp.790-805
• /
• 1988

본 연구에서는 유리섬유 강화 에폭시 복합재료의 파괴 강도와 피로 수명을 정 규분포, 로그 정규 분포와 2모수 및 3모수 Weibull 분포 함수의 기대값으로 살펴 보았 다. 2연속 응력 피로 실험 [작은 응력에서 큰 응력으로의 실험(low-high test), 큰 응력에서 작은 응력으로의 실험(high-low test)]의 결과도 분포 함수들을 사용하여 분 석하였다. 비통계학적 누적 손상 법칙들(non-statistical cumulative damage rules) 을 2연속 응력 피로 수명 분산 예측에 이용하기 위해서 동등 순위 가정(equal rank assumption)을 확장하여 수정하였다. 수정한 누적 손상 모형은 Miner의 법칙, Brou- tman과 Sahu의 손상모형 및 Hashin과 Rotem의 모형 등이다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1615-1617
• /
• 1996

In this study, epoxidized bisphenolic resins laminated with glass fiber mat(GFRP) are ivestigated on surface, bulk aspect and dielectric constant(${\varepsilon}'$ and ${\varepsilon}''$) vs. frequency characteristics with temperature. The investigation shows the different characteristics accordig to the attachments of fiber surface, filler content, matrix properties, and the others. Especially, dielectric properties of this sample are highly increased above $100^{\circ}C$ and decreased with the rise of frequency. There is a resonance at the high frequency region ($1MHz{\sim}10MHz$). So, dielectric properties show the shift with frequency and temperature. Dielectric properties of EGL 10 are higher than those of EGL 40 with the frequency. Generally, dielectric properties of EGL 10 are more unstable than those of EGL 40 on the shift of frequency and temperature.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.553-553
• /
• 2000

The application as the parts of an automobile, using the property of GMT-Sheet, is increasing. In order to exchange the parts of an automobile for GMT-Sheet, at first, the establishment and joining problem of exact joining strength must be determined. We have studied it using composites which is not same each other fiber oriented condition so as to determine joining strength and joining condition of GMT-Sheet. h this study, the result of experiment of forming condition concerned joining problem of GMT-Sheet is this ; joining efficiency of of GMT-Sheet, increases as lap joint length L increases. Increase of compression ratio causes decrease of joining efficiency after of GMT-Sheet joining. In the viewpoint of recycling, randomly oriented composite of GMT-Sheet is desirable more than unidirectional oriented composite. We has better design the structure so as not to occur to stress centralizatien on the joining part.

• 한국자동차공학회논문집
• /
• 제13권1호
• /
• pp.45-50
• /
• 2005

Stick type ignition coil(called a Cigar coil) is a kind of transformer for an automobile modulaized of distributer and electric cable. A material of cigar coil is PBT $GF30\%$ resin. This is an excellent engineering plastic with both mechanical and electrical properties. When we insert an HV terminal into the PBT $GF30\%$ resin jacket, it breaks the jacket, because the HV terminal is bigger than the jacket. It is a fatal on durability of a part. In this study, We used ANSYS FEM tool in order to stress analysis by contact. In order to automatically estimate possible maximum diameter of an HV terminal, we used an APDL. In the contact part, we considered the relation of the HV terminal's diameter with the amount of stress that occurred. This relation is able to be applied, in part, to the dimensions of the part design.