• Proceedings of the Korea Water Resources Association Conference
• /
• 2008.05a
• /
• pp.1899-1903
• /
• 2008

대수층의 저유량이 풍부한 강변여과수 개발 예정지역의 충적층(지표면하 $25{\sim}35\;m$ 구간)에서 수리전도도와 종분산지수의 규모종속효과를 규명하기 위해 양수시험과 수렴흐름 추적자시험이 수행 되었다. 양수시험과 추적자시험의 규모는 2 m 와 5 m 이었으며 양수시험은 5개 공, 추적자시험은 3개 공을 이용하여 수행되었다. 양수시험은 일정한 양수율($2,500\;m^3/day$)로 수행되었으며, 양수 시작 후 경과시간에 따른 수위변화 자료를 AQTESOLV 3.5 프로그램에 입력하여 해석하였다. 시험 대수층의 수리전도도는 양수정에서 $1.745{\times}10^{-3}\;m/sec$, 양수정에서 이격거리가 2 m 구간에서는 $2.161{\times}10^{-3}\;m/sec$와 $2.270{\times}10^{-3}\;m/sec$ 이었으며, 이격거리가 5 m 구간에서는 $2.452{\times}10^{-3}\;m/sec$와 $2.591{\time}10^{-3}m/sec$로 산정되었다. 그리고, 양수정에서 회복시험 시 Theis(Recovery) 방법에 의해 해석된 수리전도도는 $1.603{\times}10^{-3}\;m/sec$이었다. 양수정에서 관측정의 이격거리(d)에 따른 수리전도도(K) 증가함수는 log K=0.0693 log d-2.671와 log K=0.0817 log d-2.655로 추정되었으며, 결정 계수는 각각 0.965와 0.979로서 매우 높게 나타났다. 따라서 양수정에서의 이격거리가 멀수록 수리전도도가 증가하는 규모종속을 확인하였으며, 또한 시험대수층의 수리전도도가 방사상으로 유사하게 분포하고 있음을 알 수 있었다. 수렴흐름 추적자시험의 양수율은 $2,500\;m^3/day$ 이었으며, 2개의 주입정에 염소이온 5 kg을 순간 주입하였다. 염소이온의 농도이력곡선을 작성하여 초기도달시간과 최고농도의 차이를 분석하였으며, 누적질량회수곡선을 통해 양수 후 경과시간에 따른 염소이온의 질량회수율을 분석하였다. 그리고, 염소이온농도 대 누적질량회수율의 이력그래프를 작성하여 누적질량회수율에 따른 염소이온농도의 증가와 감소 변화를 분석하였다. 또한, 염소이온농도의 증가/감소 구간에 대한 선형회귀분석을 수행하여 농도 증가율과 감소율의 변화를 파악하였다. 양수정에서 관측된 경과시간별 염소이온농도 자료를 CATTI 코드의 "Converging Radial Flow With Instantaneous Injection" 해석법에 적용하여 종분산지수를 추정하였다. 양수정에서 이격거리가 2 m인 경우의 종분산지수는 0.4152 m, 이격거리가 5 m인 경우의 종분산지수는 3.2665 m이었다. 따라서 양수정에서 이격거리가 멀수록 종분산지수가 증가하는 규모종속효과를 확인하였으며, 또한 이격거리에 대한 종분산지수의 비는 각각 0.21과 0.65 정도로서 증가하였다.

• Journal of Korean Society of Forest Science
• /
• v.109 no.4
• /
• pp.429-437
• /
• 2020

In this study we quantified the long-term change in discharge against precipitation in a forested watershed and investigated how the growth of forest trees influences these changes. We found a proportional relationship between precipitation and discharge for each year, and discharge decreased gradually with time. Precipitation and discharge were highest in July and August, and the changes in precipitation, discharge, and runoff rate did not always coincide, given that high runoff rate was shown in August and September. The monthly coefficient of variation (CV) for discharge was larger than that for precipitation, and the deviation between precipitation and discharge increased gradually. From 2011 to 2017, the gradient of the trend line for the change of total discharge and direct runoff against precipitation decreased, whereas the gradient of the base flow increased in this same time period. A possible explanation is that the water holding capacity of soil deposits increased as the forest soil of the Palgong Mountain watershed developed and the increase of base flow rose with groundwater level together with that of outflow quantity. The coefficient of flood recession was lower in the period 2011 to 2017 than in 2003 to 2010; thus, the reduction of discharge was mitigated and remained steady as time progressed. We conclude from these results that the discharge of surface runoff decreased as tree growth and base flow increased; however, the water yield function of the forest increased gradually.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.10
• /
• pp.916-927
• /
• 2010

In general water treatment process, the disinfection process by chlorine is used to prevent water borne disease and microbial regrowth in water distribution system. Because chlorines were reacted with organic matter, carcinogens such as disinfection by-products (DBPs) were produced in drinking water. Therefore, a suitable injection of chlorine is need to decrease DBPs. Rechlorination in water pipelines or reservoirs are recently increased to secure the residual chlorine in the end of water pipelines. EPANET 2.0 developed by the U.S. Environmental Protection Agency (EPA) is used to compute the optimal chlorine injection in water treatment plant and to predict the dosage of rechlorination into water distribution system. The bulk decay constant ($k_{bulk}$) was drawn by bottle test and the wall decay constant ($k_{wall}$) was derived from using systermatic analysis method for water quality modeling in target region. In order to predict water quality based on hydraulic analysis model, residual chlorine concentration was forecasted in water distribution system. The formation of DBPs such as trihalomethanes (THMs) was verified with chlorine dosage in lab-scale test. The bulk decay constant ($k_{bulk}$) was rapidly decreased with increasing temperature in the early time. In the case of 25 degrees celsius, the bulk decay constant ($k_{bulk}$) decreased over half after 25 hours later. In this study, there were able to calculate about optimal rechlorine dosage and select on profitable sites in the network map.

• Nuclear Engineering and Technology
• /
• v.26 no.1
• /
• pp.126-139
• /
• 1994

Best-estimate thermal-hydraulic codes, CATHARE2 V1.2 and RELAP5/MOD3, hate been assessed against the BETHSY 6.2 tc six-inch cold leg break loss-of-coolant accident (LOCA) test. Main objective is to analyze the overall capabilities of the two codes on physical phenomena of concern during the small break LOCA i.e. two-phase critical flow, depressurization, core water level de-pression, loop seal clearing, liquid holdup, etc. The calculation results show that the too codes predict well both in the occurrences and trends of major two-phase flow phenomena observed. Especially, the CATHARE2 calculations show better agreements with the experimental data. However, the two codes, in common, show some deviations in the predictions of loop seal clearing, collapsed core water level after the loop seal clearing, and accumulator injection behaviors. The discrepancies found from the comprision with the experimental data are larger in the RELAP5 results than in the CATHARE2. To analyze the deviations of the two code predictions in detail, several sensitivity calculations have been performed. In addition to the change of two-phase discharge coefficients for the break junction, fine nodalization and some corrections of the interphase drag term are made. For CATHARE2, the change of interphase drag force improves the mass distribution in the primary side. And the prediction of SG pressure is improved by the modification of boundary conditions. For RELAP5, any single input change doesn't improve the whole result and it is found that the interphase drag model has still large uncertainties.

• Journal of the Korean Data and Information Science Society
• /
• v.26 no.3
• /
• pp.687-693
• /
• 2015

Using 378,086 lactation records on dairy cattle, environmental factors influencing acetone and ${\beta}$-hydroxybutyrate acid contents in raw milk which are used as ketosis diagnosis indicator traits were analyzed in this experiment. Significance testing was conducted on farm, lactation stage, parity, milking time and month of age by traits. The results of this experiment indicated that there was a highly significant (p < 0.01) difference in all factors and lactation stage was the most significant factor. Linear regression coefficients of month of age on daily milk yields and acetone and ${\beta}$-hydroxybutyrate acid contents were all positive, while their quadratic linear regression coefficients were negative. Least square means for milk yield at second lactation stage (36~65 days) was 19.06kg which was higher than that of late lactation stage by 6.51kg. Least square means for acetone and ${\beta}$-hydroxybutyrate acid contents at the first lactation stage (5~35 days) were highest (0.1929mM/L and 0.0742mM/L, respectively), and there was a trend that they decreased as the milking progressed, but increased slightly at the late stage of milking. However, least square means for acetone and ${\beta}$-hydroxybutyrate acid contents at the first parity were 0.1414mM/L and 0.0522mM/L, respectively, which were higher than the average milk yield after the second parity. Least square means for acetone and ${\beta}$-hydroxybutyrate acid contents of PM milk yield (0.1372mM/L and 0.0534mM/L, respectively) were higher than those of AM milk yield collectively.

• Journal of Korea Soil Environment Society
• /
• v.1 no.1
• /
• pp.67-79
• /
• 1996

Clay soils typically have low hydraulic conductivities in the presence of high polarity pore fluid, such as water. Low polarity fluids, such as hydrocarbon fuels and halogenated organic solvents, typically cannot migrate into clay pores because they cannot displace the pore water. Oxygenated additives in gasoline, such as alcohols and methyl-tert-butyl ether, are increasingly used to control air pollution emissions. These relatively polar and highly water-soluble compounds may facilitate displacement of pore water and enhance migration of fuels and solvents through clay-rich soil strata. In the reported research, the migration of gasoline-alcohol fuel mixtures (gasohol) through consolidated clay was examined. Prepared kaolinite clay samples were consolidated from slurry, and various combinations of gasoline, alcohol, and water were applied to the clays under 152 Pa gauge pressure. Movement of the fluids into the clay samples was monitored by measur ing displaced pore fluid and by magnetic resonance imaging of the samples. The structures of selected samples were examined using environmental scanning electron microscopy. Results of the research suggest that alcohol added to hydrocarbon fuels can enhance migration through some clays significantly. Gasoline did not migrate appreciably into water saturated clay, even after 14 days under pressure. The gasohol mixture migrated readily into the clay in only 20 minutes. Increased hydraulic conductivity of the clay in the presence of gasohol is hypothesized to be due to the collapse of the clays pore structure when ethanol is present, creating larger pores. Increasing pore diameter decreases the capillary pressure needed for the gasohol to replace water and allows gasohol to migrate through the clay.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.9
• /
• pp.761-772
• /
• 2015

Microfin tubes having an outside diameter (O.D.) of 7.0 mm are widely used in residential air conditioning systems and heat pumps. It is known that the mass fluxes for air conditioners and heat pumps under partial load conditions are several tens of $kg/m^2s$. However, literature surveys reveal that previous investigations were limited to mass flux over $100kg/m^2s$. In this study, we conduct R-410A evaporation heat-transfer tests at low mass fluxes ($50-250kg/m^2s$) using a 7.0 mm O.D. microfin tube. During the test, the saturation temperature was maintained at $8^{\circ}C$, and the heat flux was maintained at $4.0kW/m^2$. For comparison purposes, we also test a smooth tube with a 7.0 mm O.D. The results showed that the heat-transfer enhancement factor of the microfin tube increased as the mass flux decreased up to $150kg/m^2s$, which decreased as the mass flux further decreased. The reason for this was attributed to the change of the flow pattern from an annular flow to a stratified flow. Within the test range, the frictional pressure drops of the microfin tube were approximately the same as those of the smooth tube. We then compare experimental data obtained with the predictions obtained for the existing correlations.

• Journal of the Korean Vacuum Society
• /
• v.20 no.6
• /
• pp.456-460
• /
• 2011

Recently, the size of currently-researched components and devices reduces nano-scale. Thus, it is important and emphasizes the analyses of physical properties in nano scale. Especially, the mechanical properties are not over micro-scale components but nano-scale components with different characteristics that has been reported. However, most analytical methods for currently studying in nano-scale are related to spectroscopy and electronics, affected the limitation of viewing size that these methods give only average information. In this research, the representative nanotribology analyses, nano-indenter study the physical and mechanical properties of W-N thin film for nano region and nano depth within nano-scale that the thickness of W-N diffusion barrier has less than tens of nanometers. The Scanning probe microscopy (SPM) study the surface image. From these results, the hardness of W-N thin film underneath the nano-surface decreased from 57.67 GPa to 9.1 GPa according to the increase of nitrogen gas flow. The elastic modulus of W-N thin film underneath the nano-surface also decreased from 575.53 GPa to 178.1 GPa.

• Korean Journal of Materials Research
• /
• v.9 no.3
• /
• pp.244-250
• /
• 1999

MOCVD TiN films were prepared from a new TiN precursor, tetrakis(etylmethylamino)titanium (TEMAT) and ammonia. Deposition of TiN films from a single precursor, TEMA T yielded the growth rates of $70 to 1050\AA$/min, depending on the deposition temperature. Furthermore, the excellent bottom coverage of -90% over $0.35\mu\textrm{m}$ contacts was obtained at $275^{\circ}C$. The addition of ammonia to TEMA T lowered the resistivity of as- deposited TiN film to ~ $800\mu\omega-cm$ from $3500~6000\mu\omega-cm$ and improved the stability of TiN film in air. Examination of the films by Auger electron spectroscopy(AES) showed that the oxygen and carbon contents decreased with the addition of ammonia. However, increasing ammonia flow rate decreased the bottom coverage of TiN films over $0.5\mu\textrm{m}$ contacts, probably due to the high sticking coefficient of intermediate species produced from the gas phase reaction of TEMA T and ammonia. Based on the byproduct gases detected by the quadrupole mass spectrometer (QMS), the transammination reaction was proposed to be responsible for TiN deposition. In addition, XPS analysis revealed that the carbon in the films made from TEMA T and ammonia was metallic carbon, suggesting that $\beta$-hydrogen activation process occurs competitively with the transammination reaction.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2006.05a
• /
• pp.840-845
• /
• 2006

본 연구는 수리.수문 모형화에서의 시공간 자료 분석기술 개발에 관한 연구로서, 국내 GIS엔진인 GeoMania를 기반으로 하여 개발된 HyGIS와 수리.수문 연계모형을 확립하였으며, 주요 연구 결과로, 현재 국내에서 가장 보편적이고 광범위하게 적용되고 있는 HEC-HMS 모형과 HEC-RAS 모형을 선정하여 사용자의 편의성을 도모하고, 모형의 입 출력 구조, GIS와의 연계방안 등을 분석하여 제시하였다. 또한 HyGIS-HMS 모형과 HEC-RAS 모형의 개발은 국내 GIS엔진인 GeoMania-Pro와 Add-ON 방식으로 연계되어 구동되며, 입력자료는 GeoMania-Pro 프로그램 상에서 GUI에 의한 대화식으로 구성되었다. 하나의 시스템 상에서 DEM의 구축과 종합적인 유역분석 및 체계적인 하천에 대한 지형학적 자료구축과정을 제시하였고, 국내 하천유역 및 하도망의 Geo DB와 연계되는 시스템으로 구성하였다. Thiessen 계수 계산 결과에 신뢰성을 제고하였고, CN값 구성과정은 국내 유역상황과 자료구축과정에 적합하도록 개발하였다. 또한, GRID를 이용한 하천에 대한 지형학적 자료구축 과정에 있어 보다 정확한 계산이 가능하도록 구성되었고, HyGIS-HMS 모형 및 HyGIS-RAS 모형에 대한 입력자료의 구성이 편리하도록 GUI를 이용한 입력자료 구성 모듈이 적용되었고, 이러한 입력자료가 파일로 구성이 되어 각 모형에 적용될 수 있는 형태로 구성되었다. 본 연구는 HEC-HMS 및 HEC-RAS를 이용한 HyGIS-HMS 모형과 HyGIS-RAS 모형을 개발함로써 국내유역에 대한 수리 수문 모델링시 사용자들이 하나의 GIS 엔진상에서 필요한 제반사항을 모두 구현할 수 있도록 구성되어, 엔지니어링 회사, 수자원기술자, 수자원관련 연구자들에 의해서 활용될 수 있을 것이다.이 보다 향상될 것이다.>에서 $0.0190m^3/s$로, 갈수량$(Q_{355})$은 $0.0176m^3/s$에서 $0.0189m^3/s$로 약 7%가 증가하는 것으로 분석되었다. 결과로부터 침투 트렌치는 저수량 및 갈수량을 증가시키는 보조수단이 될 수 있다.해 보았다. 뿐만 아니라 이와 관련된 수문요소기술을 확보할 수 있을 것이다.역의 물순환 과정을 보다 명확히 규명하고자 노력하였다.으로 추정되었다.면으로의 월류량을 산정하고 유입된 지표유량에 대해서 배수시스템에서의 흐름해석을 수행하였다. 그리고, 침수해석을 위해서는 2차원 침수해석을 위한 DEM기반 침수해석모형을 개발하였고, 건물의 영향을 고려할 수 있도록 구성하였다. 본 연구결과 지표류 유출 해석의 물리적 특성을 잘 반영하며, 도시지역의 복잡한 배수시스템 해석모형과 지표범람 모형을 통합한 모형 개발로 인해 더욱 정교한 도시지역에서의 홍수 범람 해석을 실시할 수 있을 것으로 판단된다. 본 모형의 개발로 침수상황의 시간별 진행과정을 분석함으로써 도시홍수에 대한 침수위험 지점 파악 및 주민대피지도 구축 등에 활용될 수 있을 것으로 판단된다. 있을 것으로 판단되었다.4일간의 기상변화가 자발성 기흉 발생에 영향을 미친다고 추론할 수 있었다. 향후 본 연구에서 추론된 기상변화와 기흉 발생과의 인과관계를 확인하고 좀 더 구체화하기 위한 연구가 필요할 것이다.게 이루어질 수 있을 것으로 기대된다.는 초과수익률이 상승하지만, 이후로는 감소하므로, 반전거래전략을 활용하는 경우 주식투자기간은 24개월이하의 중단기가 적합함을 발견하였다. 이상의 행태적 측면과 투자성과측면의 실증결과를 통하여 한국주식시장에 있어서 시장수익률을 평균적으로 초과할 수 있는 거래전략은 존재하므로 이러한 전략을