Journal of the Korea Organic Resources Recycling Association
/
v.8
no.1
/
pp.77-82
/
2000
Seven constructed and three natural tidal flats were compared to evaluate state-of- the-art of creation and restoration technology for tidal flats. parameters studied were physico-chemical and biological characteristics of soils and rate of respiration. The natural tidal flats had higher contents of silts, nitrogen and organic matter compared to the constructed ones. The natural ones had reductive Bone below 2 cm whereas the constructed ones had oxidative zone from the surface to below 20 cm. The bacterial population in the soil of the constructed tidal flats was one to two magnitudes lower than that in the natural ones. Biomass of macrobenthos and microbial respiration rate, however, were not different significantly between the natural and the constructed tidal flats. The purification capacity by diatom+bacterial+meiobenthos and macrobenthos in the constructed tidal flats was higher than that in the natural ones due to deeper permeable layer for purification in the constructed tidal flats. There was an exceptional constructed tidal flat with similar physico-chemical and biological characteristics to natural ones. Shearing stress to the surface of the tidal flat by the flow of seawater was as low as that of natural ones. These hydraulic conditions seemed to be a controlling factor on structures and functions of tidal flats. The control of hydraulic condition seemed to be one of the most important factors to create natural-like tidal flats.
Kim, Taeyoung;Kang, Sukwon;Chang, In Seop;Kim, Hyun Woo;Sung, Je Hoon;Paek, Yee;Kim, Young Hwa;Jang, Jae Kyung
Journal of Korean Society of Environmental Engineers
/
v.39
no.10
/
pp.591-598
/
2017
Power overshoot phenomenon was observed in microbial fuel cells (MFCs) used non-catalyzed graphite felt as cathode. Voltage loss in MFCs was mainly caused by cathode potential loss. Cheap stainless steel scrubber, which has high conductivity, and Pt/C coated graphite felt as cathode were used for overcoming power overshoot and reducing the cathode potential loss in MFCs. The MFCs used stainless steel scrubber showed no power overshoot even slow catholyte flow rate and produced 29% enhanced maximum current density ($23.9A/m^3$) than MFCs used non-catalyzed graphite felt while the power overshoot phenomenon was existed in Pt/C coated MFCs. Increasing catholyte flow rate resulted in disappearing power overshoot of MFCs used non-catalyzed graphite felt. In addition, maximum power density and current density of both MFCs used non-catalyzed graphite felt and stainless steel scrubber increased by 2-3.5 times. Cathode potential losses in all region of activation loss, ohmic loss, and mass transport loss were reduced according to increase of catholyte flow rate. Therefore, stainless steel scrubber has advantages that are economical materials as electrode and prevents power overshoot, leading to enhance electricity generation. In addition, increasing catholyte flux is one of great solution when power overshoot caused by cathodic overpotential is observed in MFCs.
Journal of the korean academy of Pediatric Dentistry
/
v.34
no.3
/
pp.473-480
/
2007
The dentigerous cyst originates through alteration of stellate reticulum after amelogenesis has completed, with accumulation of fluid between the layers of the reduced enamel epithelium or between this epithelium and the tooth crown. Its incidence is relatively high on 10s or 20s of age and it is always related to the unerupted crown. Generally, it has no symptom, however, if the cyst is large or accompanied with pus formation, swelling and pain may occur. In radiographic findings, it shows impacted crown surrounded by well defined unilocular radiolucent lesion and occasionally displacement of adjacent teeth or root resorption. The goal of treatment is complete elimination of abnormal tissue preserving the tooth involved in the cyst. Enucleation and marsupialization are commonly used for the treatment. Marsupialization is the procedure which removes the partial portion of the cystic wall and connects with the oral mucosa. As the pressure in the cyst decreases, bone regeneration takes place in the defect area and cystic wall converts into normal mucosa. This procedure, however, is the most conservative procedure which allows the protection of adjacent important structures. If the eruption space is sufficient, then inducing the eruption of the permanent tooth in the cyst is also possible. In following cases, dentigerous cyst was diaganosed after clinical and radiographic examination. Marsupialazation was done to remove the cyst and induce the tooth, which was in the cyst, to erupt into the oral cavity.
Journal of Advanced Marine Engineering and Technology
/
v.37
no.8
/
pp.877-885
/
2013
A seawater pipe of the engine room in the ships is being surrounded with severely corrosive environments caused by fast flowing of the seawater, containing aggressive chloride ion and high conductivity etc.. Therefore, the leakage of the seawater from its pipe have been often occurred due to its local corrosion by aggressive chloride ions. Subsequently, its leakage area is usually welded by AC shielded metal arc welding with various electrodes. In this study, when the sea water pipe is welded with several types of electrodes such as E4301, E4311, E4313 and E4316, a difference of the corrosion resistance on the welding metal zones was investigated using an electrochemical method, observing microstructure, measuring polarization behaviors and hardness. The weld metal zone welded with E4313 electrode exhibited the lowest value of hardness compared to other weld metal zones. In addition, its zone indicated also the best corrosion resistance than those of other weld metal zones. Furthermore, all of the weld metal zones revealed a relatively better corrosion resistance than those of the base metal zones. and also showed higher hardness than the base metal zones.
It is very important to analyze the OCV change behavior during the open circuit potential holding (OCV holding) process, which accelerates the evaluation of the electrochemical durability of the PEMFC membrane. In this study, an empirical formula using the experimental data of three MEAs with different durability was created and compared. The durability evaluation time of the reinforced membrane MEA without radical scavenger inside the membrane was 383 h, and the durability evaluation time of the reinforced membrane MEA with radical scavenger inside the membrane was 1,000 and 1,650 h, respectively. The degradation of the membrane was divided into the reversible degradation that can be recovered by activation and the irreversible degradation that is not recovered. The irreversible degradation of the membrane was indicated by an increase in hydrogen permeability, and the change in hydrogen permeability was similar to the irreversible degradation constant c of all three MEAs. The initiation of irreversible deterioration without recovery is indicated by an increase in hydrogen permeability, and the OCV is not recovered due to an increase in hydrogen permeability, so the slope of the OCV recovery line (ORL) decreases, which can be confirmed by an increase in the constant c value of the empirical formula.
Kim Jung-Ho;Yi Myeong-Jong;Song Yoonho;Choi Seong-Jun;Lee Seoung Kon;Son Jeong-Sul;Chung Seung-Hwan
Geophysics and Geophysical Exploration
/
v.5
no.4
/
pp.223-235
/
2002
Since weak Bones or geological lineaments are likely to be eroded, there may develop weak Bones beneath rivers, and a careful evaluation of ground condition is important to construct structures passing through a river. DC resistivity method, however, has seldomly applied to the investigation of water-covered area, possibly because of difficulties in data aquisition and interpretation. The data aquisition having high quality may be the most important factor, and is more difficult than that in land survey, due to the water layer overlying the underground structure to be imaged. Through the numerical modeling and the analysis of a case history, we studied the method of resistivity survey at the water-covered area, starting from the characteristics of measured data, via data acquisition method, to the interpretation method. We unfolded our discussion according to the installed locations of electrodes, ie., floating them on the water surface, and installing them at the water bottom, because the methods of data acquisition and interpretation vary depending on the electrode location. Through this study, we could confirm that the DC resistivity method can provide fairly reasonable subsurface images. It was also shown that installing electrodes at the water bottom can give the subsurface image with much higher resolution than floating them on the water surface. Since the data acquired at the water-covered area have much lower sensitivity to the underground structure than those at the land, and can be contaminated by the higher noise, such as streaming potential, it would be very important to select the acquisition method and electrode array being able to provide the higher signal-to-noise ratio (S/N ratio) data as well as the high resolving power. Some of the modified electrode arrays can provide the data having reasonably high S/N ratio and need not to install remote electrode(s), and thus, they may be suitable to the resistivity survey at the water-covered area.
Kim Jung-Ho;Yi Myeong-Jong;Song Yoonho;Cho Seong-Jun;Lee Seong-Kon;Son Jeongsul
한국지구물리탐사학회:학술대회논문집
/
2002.09a
/
pp.139-162
/
2002
Since weak zones or geological lineaments are likely to be eroded, weak zones may develop beneath rivers, and a careful evaluation of ground condition is important to construct structures passing through a river. Dc resistivity surveys, however, have seldomly applied to the investigation of water-covered area, possibly because of difficulties in data aquisition and interpretation. The data aquisition having high quality may be the most important factor, and is more difficult than that in land survey, due to the water layer overlying the underground structure to be imaged. Through the numerical modeling and the analysis of case histories, we studied the method of resistivity survey at the water-covered area, starting from the characteristics of measured data, via data acquisition method, to the interpretation method. We unfolded our discussion according to the installed locations of electrodes, ie., floating them on the water surface, and installing at the water bottom, since the methods of data acquisition and interpretation vary depending on the electrode location. Through this study, we could confirm that the dc resistivity method can provide the fairly reasonable subsurface images. It was also shown that installing electrodes at the water bottom can give the subsurface image with much higher resolution than floating them on the water surface. Since the data acquired at the water-covered area have much lower sensitivity to the underground structure than those at the land, and can be contaminated by the higher noise, such as streaming potential, it would be very important to select the acquisition method and electrode array being able to provide the higher signal-to-noise ratio data as well as the high resolving power. The method installing electrodes at the water bottom is suitable to the detailed survey because of much higher resolving power, whereas the method floating them, especially streamer dc resistivity survey, is to the reconnaissance survey owing of very high speed of field work.
Koreanishche Zeitschrift fur Deutsche Sprachwissenschaft
/
v.7
/
pp.1-24
/
2003
우리는 지금까지 독일어와 한국어 두 언어간의 오류분석을 논의해 왔다. 특히 언어유형학적인 측면에서 몇 가지 오류유형과 분석을 시도했다. 그 결과는 대체로 다음과 같이 요약될 수 있다. 독일어와 한국어가 서로 근본적으로 상반되는 언어현상과 더불어 약간의 공통성을 나타내며 일정한 유형을 나타낸다. 이는 두로 인간의 언어습득장치에 기인된 언어습득의 결정주의(Determinismus)에서 비롯될 것이다. 언어특성/문제의 체계성/규칙성 또는 일관성은 이를 반영한다. 거대한 언어자료 중에 극히 미미한 일부, 즉 언어최소량를 정복함으로써 그 효용성을 극대화할 수 있는 것은 매우 중요한 의미를 지닌다. 이를 연구 이용하는 경우에는 엄청난 효과와 가능성을 기대할 수 있을 것이다. (1) 독일어와 한국어의 학습 및 오류분석에서 가장 핵심적인 것은 언어유형학적으로 드러난 언어특성, 즉 전치성(독일어/영어)과 후치성(한국어)이다. 이를 토대로 형성된 대립적인 면과 공통적인 문제를 체계화하는 것이 역시 오류분석 문제의 관건이다. 또한 독일어가 아직 후치성 언어(한국어(TXV))에서 출발해서 전치성 언어(영어(SVX))로 발전/변화해 가는 과정, 즉 중간단계인 TVX에 머물고 있다는 사실이 중요한 의미를 지닌다. 즉 그들의 대극성과 유사성을 연결하는 실마리로 볼 수 있기 때문이다. (2) 일치(Kongruenz)/상관(Korrelation) 및 반복(Wiederholung) 현상, 그리고 격변화와 인칭변화 현상은 어순문제와 더불어 형태론적 문제를 통해 문법적인 확인수단으로 작용한다. 이들은 대부분 체계적/구조적으로 나타나기 때문에 학습자는 흔히 같은 유형에서 반복적으로 오류를 범하기 마련이다. 이를 극복하기 위해서 언어 유형학적 오류분석을 이해하고 또한 이를 통해 오류를 줄이거나 예방하는 학습이 필요하다. (3) 명사가 한정사구 안에서 성/수/격에 따라 변화하는 것과 동사가 동사구에서 주어의 인칭/수에 따라 인칭변화 하는 것은 우리 한국인에게는 아주 이색적인 현상이다. 이는 양면적인 수식구조에 대한 확인수단 및 원자가에 의한 강력한 형식위주 언어인 독일어와 전위적인 단일 수식구조와 부정형 동사를 특성으로 형성된 핵/최소문 언어간의 필연적인 적응관계 및 결과라고 볼 수 있다. 이 두 가지 유형 역시 언어특성에 따라 도식화/공식화 할 수 있다. (4) 괄호현상, 즉 으뜸머리(Hauptkopf)가 버금머리(Nebenkopf)와 분리하는 것은 우리 한국인에게는 아주 이색적인 언어현상이다. 한국어에는 머리의 이동이 없기 때문이다. 긴 구문에서 버금머리를 잊어버리거나 실수하는 것은 모든 괄호구문에서 예견되는 결과이다. 그러나 이는 정치성과 후치성 언어간의 전이 과정으로 이해될 수 있다. 으뜸머리가 원래의 자리를 박차고 소속 구/문의 앞자리로 도약한 것처럼 느껴지기 때문이다. (5) 전치 및 후치 수식이 유동적으로 작용하는 독일어는 전치 수식만으로 고정된 한국어보다 복잡하지만 균형적인 언어구조이다. 이러한 수식구조에서 한국인은 흔히 형태 및 어순에서, 그리고 번역에서 오류를 범하고 만다. (6) 그러나 가장 중요한 것은 아는 것을 제대로 이용하는 문제이다. 모국어/L2를 자유로이 말하고 쓸 때까지, 즉 언어습득에는 일체이 문법이나 도표/도식을 이용할 필요가 없다는 사실이다. 이는 17세기 서구의 이성주의 철학자들의 한결같은 경고이다. 오늘날 초고속 과학문명에서 더욱 빛을 발하는 것은 당연한 결과이다. 한 언어 속에 들어있는 문법체계를 익혀 가는 것이 곧 언어습득 과정이지만, 이를 달성하는 가능성 내지 첩경은 실제적인 언어자료와 체험이지 결코 문법이나 추상적인 개념적 접근이 아님을 웅변하고 있기 때문이다. 핵심적인 문제는 모국어교육에서도 최대 장점인 대화를 통한 언어연습/대화 기회를 최대한 보장하는 데 있다. 또한 언어간섭 현상을 조장하는 분위기를 막아야 할 것이다. 이러한 의미에서 교수법 개발이 외국어/L2 성공의 관건일 것이다. (7) 언어학습에서 오류를 극복하는 데는 일차적인 실제 상황에 부합하는 대화적인 연습, 그리고 효과적인 언어자료 접촉, 즉 독서와 모방이 중요하다. 이차적이고 직접적인 것은 통사(Syntax) 및 형태론(Morphologie)를 익힐 수 있는 말/문을 끊임없이 익히는 일이다. 이것이 또한 언어최소량을 충족시켜 언어습득에 이르는 첩경이다. 자연 생태적인 모국어 학습 또는 조정 및 제도적인 언어학습에서도 실제상황에 어긋나는 문법적인 체계에 얽매이는 도식 및 도표 위주의 텟스트는 일시적인 기대일 뿐이다. 인간의 언어습득장치를 이해하지 못한 결과이기 때문이다. 문법적인 개념위주 접근은 상당한 설명이 필요해서 절박한 자료와 체험까지 앗아가기 마련이다. 더구나 이를 위해 수준을 무시하고 모국어로 일관하여 벙어리와 문맹을 자초하는 것은 참으로 어리석은 일이다. 지식 정보화 시대 및 세계화 시대에는 무엇보다도 교육 및 언어정책이 국가 발전의 원동력이다. 특히 영어를 비롯한 외국어 학습능력과 학습방법은 매우 중요하다. 학습자에게 말하고 쓰는 기본 능력을 보장하는 것이 급선무이다. 이를 위한 작업의 하나가 바로 언어간의 오류분석일 것이다. 언어의 습득과 활용이 체계적이듯이 오류분석 역시 상당히 체계적이다. 그래서 인간의 언어습득과 언어습득장치를 두고 결정론(Determinismus)이 지배적이다. 이러한 의미에서 언어습득의 3대 요소, 즉 언어습득장치를 구비한 인간으로 태어나고, 해당 언어를 통한 일관된 언어체험/학습으로 언어최소량을 충족해야 한 언어를 정복할 수 있다는 것은 결정적인 사실이다. 학생고객에게 다가서는 책임교육으로 교육개방에 대비하는 일 역시 시대적인 상황이요 또한 결정적인 단계임엔 틀림이 없을 것이다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.