• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.1
• /
• pp.199-205
• /
• 2015

Indoor positioning technology has been developed very actively for the smart phone handheld by most users. Especially, many TDOA positioning systems using acoustic signal have been studied, and it estimates the smart phone position by measuring the distance between the smart phone speaker and the microphones which is installed to receive the acoustic signal from the smart phone, and by calculating the hyperbolic equations. But there are always errors for the distance measurements, and furthermore the microphone installation error produces huge position estimation error. In this paper, the position estimation error due to the position error of acoustic sensor in the 3 dimensional TDOA positioning system, is analyzed by PDOP simulation and experiment.

• The Journal of the Acoustical Society of Korea
• /
• v.38 no.6
• /
• pp.630-636
• /
• 2019

Passive Ranging Sonar (PRS) is a type of passive sonar consisting of three sub-array on the port and starboard, and has a characteristic of detecting a target and calculating a bearing and a distance. The bearing and distance calculation requires physical sub-array position information, and the bearing and distance accuracy performance are deteriorated when the position information of the sub-array is inaccurate. In particular, it has a greater impact on distance accuracy performance using plus value of two time-delay than a bearing using average value of two time-delay. In order to improve this, a study on sub-array position error estimation and error compensation is needed. In this paper, We estimate the sub-array position error based on enetic algorithm, an optimization search technique, and propose a method to improve the performance of distance accuracy by compensating the time delay error caused by the position error. In addition, we will verify the proposed algorithm and its performance using the sea-going data.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.14 no.1
• /
• pp.31-36
• /
• 2014

A study on the indoor positioning system has been active recently for the location based service indoors. In the 3 dimensional positioning system based on the acoustic signal and TDOA technology, the error characteristics of the estimated source position would be changed depending on the number of microphones and the pattern of the microphone array. In this paper, the estimated position error according to the measured distance error between the microphones and the signal source is analyzed, and the optimum microphone array is decided considering the estimated position error patterns and the total amount of the estimated position error.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.1
• /
• pp.89-101
• /
• 2015

This paper proposes a statistical model of 3-D positions when tracking moving targets using the uncooled infrared (IR) stereo camera system. The proposed model is derived from two errors. One is the position error which is caused by the sampling pixels in the digital image. The other is the timing jitter which results from the irregular capture-timing in the infrared cameras. The capture-timing in the IR camera is measured using the jitter meter designed in this paper, and the observed jitters are statistically modeled as Gaussian distribution. This paper derives an integrated probability distribution by combining jitter error with pixel position error. The combined error is modeled as the convolution of two error distributions. To verify the proposed statistical position error model, this paper has some experiments in tracking moving objects with IR stereo camera. The 3-D positions of object are accurately measured by the trajectory scanner, and 3-D positions are also estimated by stereo matching from IR stereo camera system. According to the experiments, the positions of moving object are estimated within the statistically reliable range which is derived by convolution of two probability models of pixel position error and timing jitter respectively. It is expected that the proposed statistical model can be applied to estimate the uncertain 3-D positions of moving objects in the diverse fields.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.26 no.4
• /
• pp.397-405
• /
• 2008

The position accuracy is primarily dependent on the satellite position and signal delay caused by several elements. To know the effect of the delay on the estimated positions, we simulated GPS raw data (RINEX) with GPS errors using Bernese ver5.0. GPS errors used in this paper are Ionospheric delay, Cycle slip, Troposphere, DOP and Random error. If the baseline is short, the position error according to TEC is not large, since the ionospheric delay effect can be removed by ion-free combination. However, if the baseline is long, 3 dimensional position error up to 10cm is occurred. The 3D position error of coordinates with cycle slip is hardly ever changed up to 60% of cycle slip. Because the simulated cycle slips are equally distributed on satellites, the positioning was not seriously affected by the cycle slip. Also, if percentage of cycle slip is 60%, three dimensional error is sharply increased over 1m. The position error is calculated by using the observation data (2 hours) which was selected by DOP less than 3. And its accuracy is more improved about $3{\sim}4cm$.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1155-1160
• /
• 2007

This paper presents position error for the robot localization system using the ultrasonic wave. The distance between the receiver and a beacon can be computed by using the difference between times of flight. The distance information measured by ultrasonic wave has errors. The position is calculated by distances, and this error is caused by distance errors. The position error is different from receiver¡s position. And the position is also calculated by beacon location. This paper calculates worst case position error within measuring area, and finds beacons location to reduce the position error.

• Journal of Advanced Navigation Technology
• /
• v.8 no.1
• /
• pp.26-37
• /
• 2004

Consistent and realistic error covariance information is important for position estimation, error analysis, fault detection, and integer ambiguity resolution for differential GNSS. In designing a position domain carrier-smoothed-code filter where incremental carrier phases are used for time-propagation, formulation of consistent error covariance information is not easy due to being bounded and temporal correlation of propagation noises. To provide consistent and correct error covariance information, this paper proposes two recursive filter algorithms based on carrier-smoothed-code techniques: (a) the stepwise optimal position projection filter and (b) the stepwise unbiased position projection filter. A Monte-Carlo simulation result shows that the proposed filter algorithms actually generate consistent error covariance information and the neglection of carrier phase noise induces optimistic error covariance information. It is also shown that the stepwise unbiased position projection filter is attractive since its performance is good and its computational burden is moderate.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.41 no.3
• /
• pp.17-24
• /
• 2004

We present a P-type iterative learning control(ILC) scheme for uncertain robotic systems that perform the same tasks repetitively. The proposed ILC scheme comprises a linear feedback controller consisting of position error, and a feedforward and feedback teaming controller updated by current velocity error. As the learning iteration proceeds, the joint position and velocity mrs converge uniformly to zero. By adopting the learning gain dependent on the iteration number, we present joint position and velocity error bounds which converge at the arbitrarily tuned rate, and the joint position and velocity errors converge to zero in the iteration domain within the adopted error bounds. In contrast to other existing P-type ILC schemes, the proposed ILC scheme enables analysis and tuning of the convergence rate in the iteration domain by designing properly the learning gain.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1104-1111
• /
• 1990

A method to identify nonlinear elements position of a nonlinear system is presented. Nonlinear elements position can be identified by an equivalent error damping and stiffness matrices which are based on the equivalent linearization technique. The procedures of this technique are: (1) Obtain input force and system response. (2) Define error between the actual and linearized restoring forces. (3) Calculate linearized damping and stiffness coefficients to minimize the square error sum. Several examples are tested and found that these methods are very effective not only to locate the nonlinear elements position but also to identify the degree of nonlinearity qualitatively. Nonlinear type can be qualitatively identified by examining the plots of restoring force vs equivalent state values.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.2
• /
• pp.221-228
• /
• 2020

A sonobuoy is dropped onto the surface of water to estimate the bearing of an underwater target. A Directional Frequency Analysis and Recording (DIFAR) sonobuoy has an error in the specific angular section due to the method of estimating bearing and noise, which causes an error in target localization using multiple sonobuoys. In addition, the position of the sonobuoy continues to move, but since a sonobuoy with a GPS is intermittently arranged, it is difficult to estimate the exact position of the sonobuoy. This also causes target localization performance degradation. In this paper, we propose a technique to improve the target localization performance by compensating for bearing errors using characteristics of the DIFAR sonobuoy and multiple-sonobuoy position errors based on the intermittently arranged active sonobuoy with a GPS.